WIXLIB

QuickSpecsHP rp5700 Point of Sale (POS) SystemAfter-Market OptionsSecuritySoftwareHP L1940T 19-inch TFT Flat Panel Display – Analog/DigitalEM869AAHP L1955 19-inch TFT Flat Panel Display – Analog/DigitalPD974AAHP LP2065 20-inch TFT Flat Panel Display – Analog/DigitalEF227A4HP L5006tm 15-inch LCD Touchscreen MonitorRB146AAHP s7540 17-inch (16.0 vis) CRT MonitorPF997AAHP v7650 17-inch (16.0 vis) Flat-face CRT MonitorPF996AAKensington Security Lock KitPC766AHP Business PC Security Lock KitPV606AAHP ProtectTools (1 user)RG984AADA – 12703 North America — Version 4 — August 19, 2007Page 9

QuickSpecsHP rp5700 Point of Sale (POS) SystemTechnical SpecificationsUnit Environment and Operating ConditionsGeneral Unit Operating Guidelines Keep the computer away from excessive moisture, direct moisture and the extremes of heat and cold, to ensure thatunit is operated within the specified operating range.Leave a 10.2-cm (4-in) clearance on front side and power supply side of the computer to permit the requiredairflow.If within an enclosure, the front side should be 100% open. The clearance between the system and the cabinet mustbe at least 10 mm (0.4 inch) on the sides and top and at least 50-mm (2-inch) clearance in the rear with powersupply venting area 100% open per the above bullet.Never restrict airflow into the computer by blocking any vents or air intakes.Do not stack computers on top of each other or place computers so near each other that they are subject to eachother's re-circulated or preheated air.Occasionally clean the air vents on the front, back, and any other vented side of the computer. Lint, dust and otherforeign matter can block the vents and limit the airflow.Temperature RangeRelative HumidityOperating: 50 to 104 F (10 to 40 C)*Non-operating: -22 to 140 F(-30 to 60 C)Operating: 20% to 85% (non-condensing at ambient)Non-operating: 5% to 90% (non-condensing at ambient)Operating: 10,000 ft (3048 m)Non-operating: 30,000 ft (9144 m)Maximum Altitude(unpressurized)*NOTE: Operating temperature is de-rated 1.0 deg C per 300 m (1000 ft) to 3000 m (10,000 ft) above sea level, nodirect sustained sunlight. Maximum rate of change is 10 deg C/Hr. The upper limit may be limited by the type and numberof options installed.Power Supply240-watt – 80Plus* power supply – Active PFC*This alternate 80% efficient power supply is a requirement for US Energy Star 4.0compliance in conjunction with a select range of processors and modules.Operating Voltage Range90 to 264 VACRated Voltage Range100 to 240VACRated Line Frequency50/60 HzOperating Line Frequency Range47 – 63 HzRated Input Current5 A @ 90 VAC (3.5 A @ 90 VAC with 80% efficient power supply*)Heat DissipationStandard power supply:Typical 340 btu/hr (86 kg-cal/hr)Maximum 1260 btu/hr (397 kg-cal/hr)80% efficient power supply:Typical 273 btu/hr (69 kg-cal/hr)Maximum 1024 btu/hr (258 kg-cal/hr)Power Supply Fan80 mm variable speed fanEnergy Star 3.0 CompliantYesEnergy Star 4.0 CompliantYesFEMP Standby Power CompliantYes( 2W in S5 – Power Off)**Power Consumption in ES Mode 3WDA – 12703 North America — Version 4 — August 19, 2007Page 10

QuickSpecsHP rp5700 Point of Sale (POS) SystemTechnical Specifications– Suspend to RAM (S3)(Instantly Available PC)Processor/Cache Memory Power 3W-Down (S3)Optical Drive Spins Down WhenTBDNot In UseEnvironmental and SC/default.htmEngineering Support Center(EMESC) - Intranet Web Site onlyNOTES:* This 80% efficient power supply is a requirement for US Energy Star 4.0 compliance in conjunction with a select range ofprocessors and modules.** Power consumption in the Off/Apparent Off mode is measured and reported with the network interface controller"Wake on LAN" feature disabled in F10 Setup (default is "enabled").ROM BIOS InformationKey features of the HP BIOS in the rp5700 include: Deployment and manageability – HP BIOS provides several technologies that help integrate the HP POS system intothe enterprise, such as PXE, remote configuration, remote control, and F10 Setup support for 12 languages.Stability – HP BIOS supports the HP stable product roadmap by releasing only critical BIOS changes to the factoryand advanced change notification.Security – HP BIOS offers a robust and flexible set of security features to help the system administrator secure theirsystems from removal of sensitive data, and help prevent access by unauthorized users, subversion of OS securitypolicies, removal of hardware, flash of rogue BIOS images, and attacks on BIOS settings.Thermal and power management – The HP BIOS provides and enables thermal and power managementtechnologies to assist in operating the HP POS system in any enterprise environment.Serviceability – HP BIOS provides diagnostic and detailed service information.Upgrades and recovery – HP BIOS provides numerous ways to upgrade HP POS system, including BIOS updatesfrom within DOS (Flashlite), BIOS updates from within Windows (HPQFlash, SSM), HP Client Manager, and failsafe recovery. In addition, the HP POS system BIOS Utilities tool enables replicated BIOS setup throughout theEnterprise; it is available from within the BIOS software and from the support website.Additional HP BIOS Features Administrator password – Also known as the setup password, this helps prevent unauthorized changes to the systemconfiguration. If the administrator password is not known, the BIOS version cannot be changed and changescannot be made to BIOS settings using F10 setup or under the OS.Advanced Configuration and Power Interface (ACPI) – Represents a significant innovation in power andconfiguration management, allowing operating systems and applications to manage power based on activity andusage. Provides power conservation features under Windows XP.Ability to disable the internal speakerOther FeaturesACPI-Ready HardwareDescriptionAdvanced Configuration and Power Management Interface (ACPI).DA – 12703 North America — Version 4 — August 19, 2007Page 11

QuickSpecsHP rp5700 Point of Sale (POS) SystemTechnical Specifications SMBIOS Ver. 2.4Wired for Management SupportDual-State Power ButtonAllows the system to wake from a low power mode.Controls system power consumption, making it possible to place individual cardsand peripherals in a low-power or powered-off state without affecting otherelements of the system.System Management BIOS, previously known as DMI BIOS, for system managementinformationIntel-driven, industry-wide initiative to make Intel architecture-based PCs, servers andmobile computers more inherently manageable right out of the box and over the networkPower button acts as both an on/off button and suspend-to-sleep buttonServiceability Features of SystemDual Color Power LED on Front of Computer (Indicates Normal Operations and Fault Conditions)Diagnostic LED Explanation TableNumber of 1-second red LED blinks followed by 2-second pause, then repeats:2-processor thermal protection activated3-processor not installed4-power supply failure5-memory error6-video error7-PCA failure (ROM detected failure prior to video)8-invalid ROM, bootblock recover mode System/Emergency ROM Flash ROM CMOS Battery Holder for easyReplacement Flash Recovery with Video 3.3V Aux Power LED on SystemPCA Processor ZIF Socket for easyUpgrade Over-Temp Warning on Screen(Requires IM Agents) Clear Password Jumper DIMM Connectors for easyUpgrade Restore CD Clear CMOS Jumper NIC LEDs (integrated) (Green &Amber) Color coordinated cables andconnectors Tool-less removal of hood powersupply, slot cover, hard driveand optical drive System memory can beupgraded without removing anyinternal componentsServiceability Features of Chassis Dual Color Power LED – Toindicate normal operations andfault conditions Front power switchFeatureDescriptionDA – 12703 North America — Version 4 — August 19, 2007Page 12

QuickSpecsHP rp5700 Point of Sale (POS) SystemTechnical SpecificationsASF 2.0 support (Alert StandardFormat)TowerableDrive Self Tests (DPS)DPS Access through F10 Setupduring BootIndustry-standard specification for network alerting and remote control in operatingsystem-absent environmentsProduct can be oriented as a tower (in addition to desktop orientation) Drive Protection System A diagnostic hard drive self test. It scans critical physical components and everysector of the hard drive for physical faults and then reports any faults to the user. Running independently of the operating system, it can be accessed through aWindows-based diagnostics utility or through the computer's setup procedure. Itproduces an evaluation on whether the hard drive is the source of the problemand needs to be replaced. The system expands on the Self-Monitoring, Analysis, and Reporting Technology(SMART), a continuously running systems diagnostic that alerts the user to certaintypes of failures.SMART TechnologyAllows hard drives to monitor their own health and to raise flags if imminent failures werepredicted(Self-Monitoring, Analysis andReporting Technology) Predicts failures before they occur. Tracks fault prediction and failure indicationSMART I – Drive Failureparameters such as re-allocated sector count, spin retry count, calibration retryPredictioncountSMART II – Off-Line Data By avoiding actual hard drive failures, SMART hard drives act as "insurance"Collectionagainst unplanned user downtime and potential data loss from hard drive failureSMART III – Off-Line ReadScanning with Defect ReallocationDA – 12703 North America — Version 4 — August 19, 2007Page 13

QuickSpecsHP rp5700 Point of Sale (POS) SystemTechnical Specifications - AudioHigh DefinitionAudioTypeHigh DefinitionStereo CodecAudio JacksIntegratedYes – Realtek ALC262 codecLine-In (64-K ohm Input Impedance)Line-Out * (200 ohms Output Impedance, expects at least a 10-K ohmload)NOTE: *Internal speaker amplifier is for internal speaker only. External speakers need to bepowered externally.8 kHz – 192 kHzSamplingYes - Uses OS soft wavetableWavetableSyntheses (software)YesAnalog AudioNumber of Channels Stereo (Left & Right channels)on Line-Out(mono/stereo)1.5 WInternal AudioSpeaker PowerRatingYesInternal SpeakerYesExternal SpeakerJack(Line-Out)DA – 12703 North America — Version 4 — August 19, 2007Page 14

QuickSpecsHP rp5700 Point of Sale (POS) SystemTechnical Specifications - CommunicationsSerial PortsAll serial (COM) ports can be custom configured in either standard mode or powered mode. Byrepositioning the jumpers (provided) on the system board and on the COM port PCI add-in card(some models), each COM power can achieve power on pin 1 or pin 9. The illustration and tablebelow indicate the COM port assignments and voltage supported for each COM port.COM port assignmentDescriptionStandard Mode1COM1 (yellow)Yes2COM2Yes3COM3 (some models)Yes4COM4 (some models)Yes 5VYesYesYesYes 9VYesNoNoNo 12VYesYesYesYesThe following illustrations show how to position the jumpers on the system board and on the COMport PCI add-in card (available on some models) to achieve power on pin 1 or pin 9.P16 and P127 are located on the system board behind the COM1 port.DA – 12703 North America — Version 4 — August 19, 2007Page 15

QuickSpecsHP rp5700 Point of Sale (POS) SystemTechnical Specifications - CommunicationsP17 and J4 are located on the optional COM port cardDA – 12703 North America — Version 4 — August 19, 2007Page 16

QuickSpecsHP rp5700 Point of Sale (POS) SystemTechnical Specifications - CommunicationsIntegratedBroadcom 5755Gigabit EthernetConnectorRJ-45ControllerBroadcom 5755 PCI-Express LAN ControllerMemoryIntegrated 96Kb frame buffer memoryData ratessupported10/100/1000 MbpsComplianceIEEE 802.1P, 802.1Q, 802.2, 802.3, 802.3AB and 802.3ucompliant, 802.3x flow controlBus architecturePCI-EData path widthSingle channel, PCI-EData transfer modeBus-master DMAHardwarecertificationsFCC, B, CE, TUV- cTUVus Mark Canada and United States, TUV- GSMark for European UnionPower requirement1.33 watts @ 3.3V AUX supply with 5V toleranceBoot ROM supportYesNetwork transfermodeFull-duplexHalf-duplex (not available for the 1000BASE-T transceiver)Network transferrate10BASE-T (half-duplex) 10 Mbps10BASE-T (full-duplex) 20 Mbps100BASE-TX (half-duplex) 100 Mbps100BASE-TX (full-duplex) 200 Mbps1000BASE-T (full-duplex) 2000 MbpsDA – 12703 North America — Version 4 — August 19, 2007Page 17

QuickSpecsHP rp5700 Point of Sale (POS) SystemTechnical Specifications - CommunicationsEnvironmental2006 Agere PCI56K InternationalSoftModemOperatingtemperature32 to 131 F (0 to 55 C)Operating humidity85% at 131 F (55 C)ManagementcapabilitiesASF 2.0, ACPI, WOL and DMI 2.0, PXE 2.0, WfM 2.0, Broadcommgmt utilityAlertingASF 2.0Data TransmissionTechnology speeds: 56,000 Kbps maximum downstream data,controllerlessNOTE: 56 Kbps technology refers to download speeds only and requirescompatible modems at server sites. Other conditions may limit modemspeed. FCC limitations allow a maximum of 53 Kbps during downloadtransmissions.Data Speeds(Upload only) 4,400/12,000/9,600/7,200/4,800/2,400/1,200/300Data StandardsITU-T V.90, ITU-T, ITU-T V.34, V.44, V.42, V.42bis21, V.32bis, Bell212A, and Bell 103Fax 300 b/sFax ModeCapabilitiesITU-T T.31 class 1 FAX, V. 17, V.29, V.27ter, and V.21 Channel 2Error Correctionand DataCompressionV.44, 42bis, V.42 and MNP2-5PowerManagementACPI; PPMI 1.1 and wake support with PME and Vaux; meets PCI 2.3requirements and PC 2001 requirementsUpgradeabilityDriver upgradeable for future enhancementsVideoITU-T V.80 video ready interfaceOtherTIA/EIA 602 standard AT command setIntegrated DTE interface with speeds of up to 115.2 Kbps, parallel16550a UART-compatible interfaceOptional ring wakeup signalOperatingTemperature32 to 158 F (0 to 70 C)Operating Humidity 20% to 90%, non-condensingPowerRequires a 3.3-V auxiliary power rail on PCI busUses only one PCI load (i.e., one grant/request pair), one shared IRQ,one electrical loadChipsetAgere Systems SV92PL – Integrated PCI interface with 5-V tolerant buffersand CardBus supportDimensions (L X H)Complies with PCI low profile specifications–6.7 x 2.3 in (17.0 x 5.8 cm)and supports high- and low-profile bracketsConnectionSingle RJ-11 connectorDA – 12703 North America — Version 4 — August 19, 2007Page 18

QuickSpecsHP rp5700 Point of Sale (POS) SystemTechnical Specifications - CommunicationsOther FeaturesDigital line protection, call progress monitoring via on-board piezodevice, support for high profile and low profile brackets, PnP ID supportSafetyUL recognized to UL 1950, 3rd edition (U.S. and Canada); IEC 950(TUV, NEMKO, DEMKO, SEMKO); CE Mark, EC 950 (TUV, NEMKO,DEMKO, SEMKO, CE markEMCFCC Part 15, IC ES003, EN 55022, 3rd edition, EN 55024, annex A,EN 61000-4-6, EN 61000-4-8TelecomFCC Part 68, IC-CS-03 (Canada); Worldwide PTT approvalsNot available in Korea or the Republic of South Africa.OtherBare PCB material compliant to 94V-0 or better (marked as such)PC 2001 compliant, PCI version 2.3, WHQL approved; ACPI compliantDA – 12703 North America — Version 4 — August 19, 2007Page 19

QuickSpecsHP rp5700 Point of Sale (POS) SystemTechnical Specifications - GraphicsIntegrated Graphics Graphic ControllerMedia Accelerator Bus type3000RAMDACIntegrated GMA 3000IntegratedSingle 400 MHz integratedMemoryUMA with DVMT 4.0 support for frame buffer sizes 8-256 MBController clockspeed667 MHzOverlay planesOne 16-bit video overlay planeMaximum ColorDepth32 bppMaximum verticalrefresh rate85 HzMulti-displaySupportOne VGA and one DVI-D in conjunction with an ADD2 card, clone andextended desktop modes are enabled by the addition of the HP ADD2DVI-D AdapterGraphics/Video API DirectX 9.0c, WGF 1.0, DirectX VA 2.0, Shader Model 3.0, OpenGL1.5SupportResolutionsSupported1Resolution640 x 480800 x 6001024 x 7681280 x 10241600 x 12001920 x 10801920 x 12001920 x 1440Maximum Refresh Rate (Hz)Analog MonitorDigital S:Modes listed are supported with a single active display. The supported mode list for multipleactive displays is a subset of this list. Not all modes will support video playback and somesupported modes may use software MC (motion compensation) rather than hardware MC. Not allmodes will support 3D acceleration depending on the system configuration (e.g., resolutionselected, size of frame buffer, number of installed memory modules, etc.).2-R denotes reduced blanking timings (some digital monitors may not support reduced blankingtimings).Other resolutions and refresh rates may be selectable but are not recommended.1ADD2 SDVO DVII/TV-Out AdapterForm FactorLow-profile card (full-height (ATX) and low-profile brackets included inkit)Dual head supportYesHost InterfaceConnector Mechanically compliant with PCI-e standardComplies with the Intel ADD2 and Intel Serial Digital VideoOutput (SDVO) specificationsDA – 12703 North America — Version 4 — August 19, 2007Page 20

QuickSpecsHP rp5700 Point of Sale (POS) SystemTechnical Specifications - GraphicsDot Clock165 MHz maximumDisplay ModesSupports display modes that require up to 165-MHz bandwidth on thelink, as shown in the following table.ResolutionsSupportedResolutionsBlanking640 x 480 VGA800 x 600 SVGA1024 x 768 XGA1280 x 1024 SXGA1600 x 1200 UXGAColor NoAll modes support 8-bpp, 16-bpp, and 24-bpp color depths (up to 16.7million colors)DA – 12703 North America — Version 4 — August 19, 2007Page 21

QuickSpecsHP rp5700 Point of Sale (POS) SystemTechnical Specifications - Hard DrivesSerial ATA 1.5-Gb/s 250 GBHard Drives (7200rpm)Capacity250,059,350,016 bytesHeight1 in (2.6 cm)WidthMedia diameter: 3.5 in (8.9 cm)Physical size: 4 in (10.2 cm)InterfaceSerial ATA (3.0 Gb/s)SynchronousTransfer Rate(Maximum)Up to 3 Gb/sBuffer8 MBSingle TrackSeek Time (typicalreads, includes controller Averageoverhead, includingFull-Strokesettling)160-GB1.0 ms8.5 ms18 msRotational Speed7,2

Microsoft Dynamics - Point of Sale 2.0* DA - 12703 North America — Version 4 — August 19, 2007 Page 3. QuickSpecs HP rp5700 Point of Sale (POS) System Standard and Configurable Components DA - 12703 North America — Version 4 — August 19, 2007 Page 4 * Sold separately.