Transcription
REd Dot ScopeViper red dot
VIPER RED DOTThe Viper Red Dot combines speed and simplicityin a tiny, powerful package. The 6 MOA dotdiameter gets you on target fast.Down ArrowPower On/OffDecrease BrightnessUp ArrowPower OnIncrease Brightness2Anti-reflective lens coating on lenssurface for brighter viewsArmorTek protects exterior lens fromscratches, oil, and dirt.ElevationAdjustmentDialO-ring sealed for waterproofperformance.Windage and ElevationAdjustment Lock ScrewsWindageAdjustmentDialShockproof construction withstandsimpact.13
VIPER RED DOTProtective CoverBatteryRemove cover when using or adjusting Viper red dot.Please note that installing the cover does NOT shutthe Viper off.To install, place the battery in the circular slot withnumbers facing outward. Attach the body to thebase using the two attachment screws.CR 2032BatteryProtective CoverBaseBattery Compartment4235
VIPER RED DOTPowering UpWindage and Elevation AdjustmentTo turn the Viper on, press either the up or downarrow. To turn off, press and hold the down arrow forfive seconds.The Viper features adjustable elevation and windagedials with 1 MOA marks.Power OnPress the up ordown arrow.Note: The adjustments are protected by lock screwswhich must be loosened with thesmall screwdriver before anyadjustments are made.Elevation DialPower OffPress and holdthe down arrow.Brightness AdjustmentsAdjust the illumination instensity using theappropriate arrow button: Tap the up arrow to increase brightness. Tap the down arrow to decrease brightness.Lock ScrewsWindage DialOne dial mark yields one MOA of adjustment.One MOA 1.05 inches @100 yards.To adjust the elevation and windage settings:1. Loosen the Adjustment Lock Screws 1½ turns.2. Adjust dials up or down or left or right asindicated by arrows.3. Re-tighten lock screws after making adjustments.6457
VIPER RED DOTMOUNTINGTHEVIPERThe Viper red dot is shipped from the factory witha low rail mount that clamps to both a Weaver orPicatinny rail.Mounting OptionsIn addition to the supplied low rail mount, anoptional riser mount places the Viper red dot atcorrect height for AR-15 rifles.Note: If your firearm isnot already equippedwith a base rail, it maybe purchased from manyfirearms dealers.1. Attach the low railmount to the Viper usingthe included screws.2. Attach the Viper to thePicatinny base rail, makingsure the recoil lug is solidlyseated in the base groove.3. Check to see that the clamp is fully down andhooked around the outside of the base.4. Press the Viper down and forward towardthe muzzle and, using the supplied hex wrench,firmly tighten down the clamp screw.86Check www.vortexoptics.com for other mount options.79
VIPER RED DOTSighting InAfter mounting, an initial sight-in of the Viper reddot at 25 yards will be helpful. Final sight-in shouldbe done at the desired distance (typically 25-50yards).1. Be sure the windage and elevation lock screwsare tight before firing. Fire a three-shot group asprecisely as possible at 25 yards. Loosen the Windage and Elevation AdjustmentLock Screws before adjusting. Using the center of the three-shot group as areference, make the necessary adjustments forwindage and elevation correction. Using arrowsfor reference, adjust dials in the direction youwish the group to move. At 25 yards, each dialmark will yield about ¼ inch of adjustment. Re-tighten the lock screws.2. Fire a three-shot group at final preferred sight-indistance (25-50 yards). Loosen windage and elevation lock screwsbefore adjusting. Using the center of the three-shot group asa reference, make necessary adjustments forwindage and elevation correction. Using arrowsfor reference, adjust dials in the direction youwish the group to move. At 50 yards, each dialmark will yield about ½ inch of adjustment. After achieving satisfactory zero, re-tightenlock screws.3. Fire a final three-shot group to confirm properadjustment. Repeat as necessary. Confirm that all mounting screws and lockscrews are snug and tight.101189
VIPER RED DOTMaintenanceTroubleshootingCleaningThe Viper red dot will require very little routinemaintenance other than periodically cleaning theexterior lenses. If desired, the exterior lens may becleaned by wiping with a soft, dry cloth.When cleaning the lenses, be sure to use productsthat are specifically designed for use on coatedoptical lenses such as the Vortex Lens Pen andFogFree Cleaning Kits.If the red dot does not illuminate, please check thefollowing before returning the red dot for service: Is the battery oriented correctly? Be sure thebattery is installed with the side facing upwards. Is the battery dead? If so, replace the battery. Be sure to blow away any dust or grit on the lensprior to wiping the surface. Using your breath, or a very small amount ofwater or pure alcohol, can help remove stubbornthings like dried water spots.12131011
VIPER RED DOTVIP WarrantyWe build optics based on our commitment to yourabsolute satisfaction. That’s why Vortex products areunconditionally guaranteed and we make this VeryImportant Promise to you—a Very Important Person.Rest assured that in the event your optic becomesdamaged or defective, Vortex Optics will repair orreplace it at no charge to you. If we cannot repairyour riflescope, we will replace it with a riflescope inperfect working order and in equal or better physicalcondition. Call Vortex Optics at 800-426-0048 forprompt, professional, and friendly service.Vortex Optics2120 West Greenview DriveMiddleton, WI 53562service@vortexoptics.comVisit www.vortexoptics.com for more information.Canadian customers may visit www.vortexcanada.netfor customer service information.Note: The VIP Warranty does not cover loss, theft,deliberate damage, or cosmetic damage that doesnot hinder the performance of the product.Dual Use: Shooting Tactical / Hunting141215
REd Dot ScopeManual #VRD-RD-15A Vortex Optics USA
VIPER RED DOT 8 9 MOUNTING THE VIPER In addition to the supplied low rail mount, an optional riser mount places the Viper red dot at correct height for AR-15 rifl es. Mounting Options 6 7 The Viper red dot is shipped from the factory with a low rail mount that clamps to both a Weaver or Picatinny rail. Note: If your fi rearm is not already equipped
