WIXLIB

Profile E01PSA Width: 0.070 [1.8]inches rethaneFoamPressure-SensitiveAdhesive (PSA)Dimensions for reference onlyACTUAL SIZETHINK SCHLEGEL FOR SHIELDING.Recommended Minimum Compression: 30% Recommended Maximum Compression: 70%Contact resistance between a shielding gasket and the mating surface is related to applied load andpercent compression of the gasket. This table is intended to assist in defining the optimum designrange for an application. Determined by commonly accepted test procedures under controlledconditions, these values may differ from actual performance under specific operating conditions.Contact a Schlegel EMI representative for design assistance and additional information.EMI ShieldingProductsHBUL 94 HBV-OTest Part: E0113Test Method: LP-3001 UL 94 V-OUL is a registered trademark of Underwriters Laboratories, Inc.See tab 2 (GasketOverview) forThe preceding information is believed accurate by Schlegel EMI. In no event, however, shall Schlegel EMI have any liability whatsoevericon definitions for inaccuracies or omissions contained therein. In all cases, details and values should be verified by the customer. These products arecovered by various U.S. and foreign patents.www.schlegel.com 2004 Schlegel Systems, Inc.

Profile E02PSA Width: 0.250 [6.4]C-Foldinches .9]0.170[4.3]Pressure-SensitiveAdhesive (PSA)0.550[14.0]Dimensions for reference onlyACTUAL SIZETHINK SCHLEGEL FOR SHIELDING.Recommended Minimum Compression: 40% Recommended Maximum Compression: 70%Contact resistance between a shielding gasket and the mating surface is related to applied load andpercent compression of the gasket. This table is intended to assist in defining the optimum designrange for an application. Determined by commonly accepted test procedures under controlledconditions, these values may differ from actual performance under specific operating conditions.Contact a Schlegel EMI representative for design assistance and additional information.UL 94 .040Ohms-InchHBLoad in Lbs/ftContact Resistance and Compression-Load DeflectionEMI on PercentageV-O Test Part: E0219Load forceContact resistanceTest Method: LP-3001UL 94 V-OUL is a registered trademark of Underwriters Laboratories, Inc.See tab 2 (GasketOverview) forThe preceding information is believed accurate by Schlegel EMI. In no event, however, shall Schlegel EMI have any liability whatsoevericon definitions. for inaccuracies or omissions contained therein. In all cases, details and values should be verified by the customer. These products arecovered by various U.S. and foreign patents.www.schlegel.com 2004 Schlegel Systems, Inc.

Profile E03PSA Width: 0.070 [1.8]inches m0.039[1.0]Pressure-SensitiveAdhesive (PSA)Dimensions for reference onlyACTUAL SIZETHINK SCHLEGEL FOR SHIELDING.Recommended Minimum Compression: 20% Recommended Maximum Compression: 70%Contact resistance between a shielding gasket and the mating surface is related to applied load andpercent compression of the gasket. This table is intended to assist in defining the optimum designrange for an application. Determined by commonly accepted test procedures under controlledconditions, these values may differ from actual performance under specific operating conditions.Contact a Schlegel EMI representative for design assistance and additional information.HBEMI ShieldingProductsUL 94 HBV-OTest Part: E0313Test Method: LP-3001 UL 94 V-OUL is a registered trademark of Underwriters Laboratories, Inc.See tab 2 (GasketOverview) forThe preceding information is believed accurate by Schlegel EMI. In no event, however, shall Schlegel EMI have any liability whatsoevericon definitions for inaccuracies or omissions contained therein. In all cases, details and values should be verified by the customer. These products arecovered by various U.S. and foreign patents.www.schlegel.com 2004 Schlegel Systems, Inc.

Profile E04PSA Width: 0.125 [3.2]inches .300[7.6]Pressure-SensitiveAdhesive (PSA)Dimensions for reference onlyACTUAL SIZETHINK SCHLEGEL FOR SHIELDING.Recommended Minimum Compression: 10% Recommended Maximum Compression: 60%Contact resistance between a shielding gasket and the mating surface is related to applied load andpercent compression of the gasket. This table is intended to assist in defining the optimum designrange for an application. Determined by commonly accepted test procedures under controlledconditions, these values may differ from actual performance under specific operating conditions.Contact a Schlegel EMI representative for design assistance and additional information.UL 94 .015Ohms-InchHBLoad in Lbs/ftContact Resistance and Compression-Load Deflection0.010EMI ShieldingProducts020%30%40%50%60%Compression PercentageV-OLoad forceContact resistanceTest Part: E0419Test Method: LP-3001 UL 94 V-OUL is a registered trademark of Underwriters Laboratories, Inc.See tab 2 (GasketOverview forThe preceding information is believed accurate by Schlegel EMI. In no event, however, shall Schlegel EMI have any liability whatsoevericon definitions for inaccuracies or omissions contained therein. In all cases, details and values should be verified by the customer. These products arecovered by various U.S. and foreign patents.www.schlegel.com 2004 Schlegel Systems, Inc.

Profile E05PSA Width: 0.250 [6.4]inches UrethaneFoamPressure-SensitiveAdhesive (PSA)Dimensions for reference onlyACTUAL SIZETHINK SCHLEGEL FOR SHIELDING.Recommended Minimum Compression: 20% Recommended Maximum Compression: 60%Contact resistance between a shielding gasket and the mating surface is related to applied load andpercent compression of the gasket. This table is intended to assist in defining the optimum designrange for an application. Determined by commonly accepted test procedures under controlledconditions, these values may differ from actual performance under specific operating conditions.Contact a Schlegel EMI representative for design assistance and additional information.UL 94 chHBLoad in Lbs/ftContact Resistance and Compression-Load DeflectionEMI ShieldingProductsCompression PercentageTest Part: E0519UL 94 V-OLoad forceContact resistanceTest Method: LP-3001UL is a registered trademark of Underwriters Laboratories, Inc.See tab 2 (GasketOverview) forThe preceding information is believed accurate by Schlegel EMI. In no event, however, shall Schlegel EMI have any liability whatsoevericon definitions for inaccuracies or omissions contained therein. In all cases, details and values should be verified by the customer. These products arecovered by various U.S. and foreign patents. www.schlegel.com 2004 Schlegel Systems, Inc.

Profile E06PSA Width: 0.125 [3.2]inches m0.039[1.0]Pressure-SensitiveAdhesive (PSA)Dimensions for reference onlyACTUAL SIZETHINK SCHLEGEL FOR SHIELDING.Recommended Minimum Compression: 10% Recommended Maximum Compression: 70%Contact resistance between a shielding gasket and the mating surface is related to applied load andpercent compression of the gasket. This table is intended to assist in defining the optimum designrange for an application. Determined by commonly accepted test procedures under controlledconditions, these values may differ from actual performance under specific operating conditions.Contact a Schlegel EMI representative for design assistance and additional information.UL 94 .0080.0060.004020%30%40%50%60%Ohms-InchHBLoad in Lbs/ftContact Resistance and Compression-Load DeflectionEMI ShieldingProducts70%Compression PercentageV-OTest Part: E0619Load forceContact resistance Test Method: LP-3001UL 94 V-OUL is a registered trademark of Underwriters Laboratories, Inc.See tab2 (GasketOverview) foricon definitionsThe preceding information is believed accurate by Schlegel EMI. In no event, however, shall Schlegel EMI have any liability whatsoeverfor inaccuracies or omissions contained therein. In all cases, details and values should be verified by the customer. These products arecovered by various U.S. and foreign patents.www.schlegel.com 2004 Schlegel Systems, Inc.

Profile E07PSA Width: 0.125 [3.2]inches ensitiveAdhesive (PSA)UrethaneFoam0.079[2.0]Dimensions for reference onlyACTUAL SIZETHINK SCHLEGEL FOR SHIELDING.Recommended Minimum Compression: 10% Recommended Maximum Compression: 70%Contact resistance between a shielding gasket and the mating surface is related to applied load andpercent compression of the gasket. This table is intended to assist in defining the optimum designrange for an application. Determined by commonly accepted test procedures under controlledconditions, these values may differ from actual performance under specific operating conditions.Contact a Schlegel EMI representative for design assistance and additional information.I/OHBEMI ShieldingProductsUL 94 HBV-OTest Part: E0713Test Method: LP-3001 UL 94 V-OUL is a registered trademark of Underwriters Laboratories, Inc.See tab 2 (GasketOverview) forThe preceding information is believed accurate by Schlegel EMI. In no event, however, shall Schlegel EMI have any liability whatsoevericon definitions for inaccuracies or omissions contained therein. In all cases, details and values should be verified by the customer. These products arecovered by various U.S. and foreign patents.www.schlegel.com 2004 Schlegel Systems, Inc.

Profile E08PSA Width: 0.125 [3.2]inches am0.079[2.0]Pressure-SensitiveAdhesive (PSA)Dimensions for reference onlyACTUAL SIZETHINK SCHLEGEL FOR SHIELDING.Recommended Minimum Compression: 10% Recommended Maximum Compression: 70%Contact resistance between a shielding gasket and the mating surface is related to applied load andpercent compression of the gasket. This table is intended to assist in defining the optimum designrange for an application. Determined by commonly accepted test procedures under controlledconditions, these values may differ from actual performance under specific operating conditions.Contact a Schlegel EMI representative for design assistance and additional information.I/OHBEMI ShieldingProductsUL 94 HBV-OTest Part: E0813Test Method: LP-3001UL 94 V-O UL is a registered trademark of Underwriters Laboratories, Inc.See tab 2 (GasketOverview) forThe preceding information is believed accurate by Schlegel EMI. In no event, however, shall Schlegel EMI have any liability whatsoevericon definitions for inaccuracies or omissions contained therein. In all cases, details and values should be verified by the customer. These products arecovered by various U.S. and foreign patents.www.schlegel.com 2004 Schlegel Systems, Inc.

Profile E09PSA Width: 0.125 [3.2]inches am0.079[2.0]Pressure-SensitiveAdhesive (PSA)Dimensions for reference onlyACTUAL SIZETHINK SCHLEGEL FOR SHIELDING.Recommended Minimum Compression: 10% Recommended Maximum Compression: 60%Contact resistance between a shielding gasket and the mating surface is related to applied load andpercent compression of the gasket. This table is intended to assist in defining the optimum designrange for an application. Determined by commonly accepted test procedures under controlledconditions, these values may differ from actual performance under specific operating conditions.Contact a Schlegel EMI representative for design assistance and additional information.HBUL 94 .015Ohms-InchI/OLoad in Lbs/ftContact Resistance and Compression-Load Deflection0.010EMI ShieldingProducts020%30%40%50%60%Compression PercentageV-OTest Part: E0919Load forceContact resistanceTest Method: LP-3001 UL 94 V-OUL is a registered trademark of Underwriters Laboratories, Inc.See tab 2 (GasketOverview) forThe preceding information is believed accurate by Schlegel EMI. In no event, however, shall Schlegel EMI have any liability whatsoevericon definitions for inaccuracies or omissions contained therein. In all cases, details and values should be verified by the customer. These products arecovered by various U.S. and foreign patents.www.schlegel.com 2004 Schlegel Systems, Inc.