WIXLIB

R&S FPC1000Spectrum AnalyzerSpecificationsData Sheet Version 01.00 year

Version 01.00, December 2016CONTENTSDefinitions . 3Specifications . 4Frequency . 4Sweep time. 4Bandwidth. 4Level. 5Trigger functions . 6Inputs and outputs . 6General data. 7Ordering information . 8Options . 8Accessories . 8Service options . 82Rohde & Schwarz R&S FPC1000 Spectrum Analyzer

Version 01.00, December 2016DefinitionsGeneralProduct data applies under the following conditions: Three hours storage at ambient temperature followed by 30 minutes warm-up operationSpecified environmental conditions metRecommended calibration interval adhered toAll internal automatic adjustments performed, if applicableSpecifications with limitsRepresent warranted product performance by means of a range of values for the specified parameter. These specifications aremarked with limiting symbols such as , , , , , or descriptions such as maximum, limit of, minimum. Compliance is ensured bytesting or is derived from the design. Test limits are narrowed by guard bands to take into account measurement uncertainties, driftand aging, if applicable.Specifications without limitsRepresent warranted product performance for the specified parameter. These specifications are not specially marked and representvalues with no or negligible deviations from the given value (e.g. dimensions or resolution of a setting parameter). Compliance isensured by design.Typical data (typ.)Characterizes product performance by means of representative information for the given parameter. When marked with , or as arange, it represents the performance met by approximately 80 % of the instruments at production time. Otherwise, it represents themean value.Nominal values (nom.)Characterize product performance by means of a representative value for the given parameter (e.g. nominal impedance). In contrast totypical data, a statistical evaluation does not take place and the parameter is not tested during production.Measured values (meas.)Characterize expected product performance by means of measurement results gained from individual samples.UncertaintiesRepresent limits of measurement uncertainty for a given measurand. Uncertainty is defined with a coverage factor of 2 and has beencalculated in line with the rules of the Guide to the Expression of Uncertainty in Measurement (GUM), taking into accountenvironmental conditions, aging, wear and tear.Device settings and GUI parameters are indicated as follows: “parameter: value”.Typical data as well as nominal and measured values are not warranted by Rohde & Schwarz.In line with the 3GPP/3GPP2 standard, chip rates are specified in Mcps (million chips per second), whereas bit rates and symbol ratesare specified in Mbps (million bits per second), kbps (thousand bits per second) or ksps (thousand symbols per second), and samplerates are specified in Msample/s (million samples per second). Mcps, kbps, ksps and Msample/s are not SI units.Rohde & Schwarz R&S FPC1000 Spectrum Analyzer3

Version 01.00, December 2016SpecificationsSpecifications apply under the following conditions:15 minutes warm-up time at ambient temperature, specified environmental conditions met, calibration cycle adhered to.Data without tolerances: typical values only. Data designated as “nominal” applies to design parameters and is not tested. Datawithout tolerance limits is not binding.FrequencyFrequency rangeR&S FPC1000with R&S FPC-B2 optionwith R&S FPC-B3 optionFrequency resolutionReference frequency, internalAging per yearTemperature drift0 C to 30 C 30 C to 50 CAchievable initial calibration accuracyTotal reference uncertaintyFrequency readoutMarker resolutionUncertaintyNumber of sweep (trace) pointsMarker tuning frequency step sizeFrequency counter resolutionCount uncertaintySNR 25 dBFrequency spanwith R&S FPC-B2 optionwith R&S FPC-B3 optionSpan uncertaintySpectral purity SSB phase noiseCarrier offset5 kHz to 1 GHz5 kHz to 2 GHz5 kHz to 3 GHz1 Hz1 10–61 10–63 10–65 10–7(time since last adjustment aging rate) temperature drift calibration accuracy0.1 Hz (marker frequency referenceuncertainty 10 % resolution bandwidth ½ (span / (sweep points – 1)) 1 Hz)1183span/11820.1 Hz (frequency reference uncertainty ½ (last digit))0 Hz, 10 Hz to 1 GHz0 Hz, 10 Hz to 2 GHz0 Hz, 10 Hz to 3 GHznominal 1 %30 kHz100 kHz1 MHzf 500 MHz –88 dBc (1 Hz), –92 dBc (1 Hz) (typ.) –98 dBc (1 Hz), –103 dBc (1 Hz) (typ.) –120 dBc (1 Hz), –125 dBc (1 Hz) (typ.)span 0 Hz10 Hz span 600 MHzspan 600 MHzspan 0 Hzspan 10 Hz100 µs to 100 s10 ms to 1000 s10 ms span/600 MHz to 1000 snominal 1 %nominal 3 %–3 dB bandwidth1 Hz RBW 300 kHz300 kHz RBW 1 MHz1 Hz to 3 MHz in 1/3 sequencenominal 5 %nominal 10 %nominal 5 (Gaussian type filters)–3 dB bandwidth1 Hz to 3 MHz in 1/3 sequenceSweep timeSweep timeUncertaintyBandwidthResolution bandwidthsRangeBandwidth accuracySelectivity 60 dB:3 dBVideo filtersRange4Rohde & Schwarz R&S FPC1000 Spectrum Analyzer

Version 01.00, December 2016LevelDisplay rangeMaximum rated input levelDC voltageCW RF powerPeak RF powerMax. pulse voltageMax. pulse energyIntermodulationThird-order intercept (TOI),Second harmonic intercept (SHI)displayed noise floor to 30 dBm50 V33 dBm ( 2 W)36 dBm ( 4 W)150 V10 mWsduration 3 spulse width 10 µsintermodulation-free dynamic range, signal level 2 –20 dBm, RF attenuation 0 dB,RF preamplifier offfin 1 GHz 7 dBm (meas.)fin 2.4 GHz 10 dBm (meas.)RF attenuation 0 dB, RF preamplifier off, signal level –40dBmfin 20 MHz to 1.5 GHz–60 dBc (nom.)Displayed average noise level0 dB RF attenuation, termination 50 Ω, RBW 100 Hz, VBW 10 Hz,sample detector, log scaling, normalized to 1 Hzfrequencypreamplifier R&S FPC1000 off1 MHz to 10 MHz –127 dBm,–135 dBm (typ.)10 MHz to 1 GHz –142 dBm, –146 dBm (typ.)1 GHz to 3 GHz –140 dBm, –144 dBm (typ.)frequencypreamplifier R&S FPC1000 on(requires R&S FPC-B22 option)1 MHz to 10 MHz –147 dBm, –157 dBm (typ.)10 MHz to 3 GHz –158 dBm, –163 dBm (typ.)Immunity to interference, nominal valuesImage frequenciesfin – 2 30.15 MHzfin – 2 830.15 MHzfin – 2 4042.65 MHzIntermediate frequencies30.25 MHz, 830.25 MHz, 4042.65 MHzOther interfering signals,spurious at fin – 2021.325 MHzsignal level – RF attenuation –30 dBmOther interfering signals, related to local f 300 kHzoscillatorsf receive frequencyResidual spurious responseinput matched with 50 Ω,without input signal, RBW 30 kHz,f 3 MHz, RF attenuation 0 dB,Wifi function disabledLevel displayLogarithmic level axisLinear level axisNumber of tracesTrace detectorsTrace functionsSetting range of reference levelUnits of level axisLevel measurement uncertaintyAbsolute level uncertainty at 100 MHzFrequency response ( 20 C to 30 C)Attenuator uncertaintyUncertainty of reference level settingDisplay nonlinearityBandwidth switching uncertaintyTotal measurement uncertainty 20 C to 30 C100 kHz f 10 MHz10 MHz f 3 GHz –70 dBc (nom.) –65 dBc (nom.)–60 dBc (nom.) –70 dBc (nom.) –60 dBc (nom.) –60 dBc (nom.) –90 dBm (nom.)1/2/5/10/20/50/100 dB, 10 divisions0 % to 100 %, 10 divisions2max. peak, min. peak, auto peak, sample,RMSclearWrite, max hold, min hold, average,view–130 dBm to 30 dBmdBm, dBmV, dBµV, V, W 0.3 dB 1.5 dB (nom.) 1 dB 0.3 dB 0.1 dB (nom.) 0.3 dBSNR 16 dB, 0 dB to –50 dB,logarithmic level displayreference: RBW 10 kHz 0.1 dB (nom.)95 % confidence level, 20 C to 30 C,SNR 16 dB, 0 dB to –50 dB below reference level, RF attenuation auto10 MHz f 3 GHz 1.25 dB, typ. 0.5 dBRohde & Schwarz R&S FPC1000 Spectrum Analyzer5

Version 01.00, December 2016Trigger functionsTriggerTrigger sourceExternal trigger level thresholdlow high transitionhigh low transitionmaximumfree run, video, external2.4 V0.7 V3.0 V5 kHz f 1 GHz1 GHz f 3 GHzRF input only50 Ω (nom.)N female 1.5 (nom.) 2 (nom.)0 dB to 40 dB in 5 dB stepsInputs and outputsRF inputImpedanceConnectorVSWRInput attenuatorAF outputAF demodulation typesConnectorOutput impedanceVoltage (open circuit)External reference, external triggerConnectorModeExternal referenceExternal trigger threshold6AM and FM3.5 mm mini jack32 Ω (nom.)VRMS adjustable from 0 V to 100 mVrequired levelfrequencylow high transitionhigh low transitionRohde & Schwarz R&S FPC1000 Spectrum AnalyzerBNC, 50 Ωext. reference, ext. trigger0 dBm10 MHz2.4 V0.7 V

Version 01.00, December 2016General dataPower supplyAC supplyinput specifications100 V AC to 240 V AC, 50 Hz to 60 Hz,0.6 A to 0.4 A14 W (nom.)IEC 61010-1, EN 61010-1, UL 61010-1,CAN/CSA-C22.2 No. 61010.1VDE, GS, CSAPower consumptionSafetyTest markManual operationLanguagesChinese, English, French, German, Italian,Hungarian, Japanese, Korean,Portuguese, Russian, SpanishRemote controlCommand setLAN interfaceUSBDisplaySizeResolutionPixel errorsAudioSpeakerUSB interfaceSCPI 1997.010/100BASE-T, RJ-45type B plug, version 2.010.1"1366 768 pixel 2 pixelnumber of interfacesinternaltype A plug, version 2.02internalon memory stick, 1 Gbytememory stick (not supplied),size 4 Gbyte, USB version 1.1 or 2.0 256 instrument settings and traces 5000 instrument settings and tracesMass memoryMass memoryData storageEnvironmental conditionsTemperatureClimatic loadingMechanical resistanceVibrationoperating temperature rangestorage temperature rangerelative humidity 10 C to 40 C–20 C to 70 C 25/ 40 C at 85 % relative humidity(EN 60068-2-30)sinusoidalrandomEN 60068-2-6EN 60068-2-6440 g shock spectrum,in line with MIL-STD-810F, method 516.4procedure 1, EN 60068-2-27in line with European EMC Directive2004/108/EC includingCISPR 11/EN 55011/group 1class A (emission)EN 61326 table 2(immunity, industrial)396 mm 178 mm 147 mm(15.6 in 7 in 5.8 in)396 mm 185 mm 156 mm(15.6 in 7.3 in 6.1 in)3 kg (6.61 lb)1 yearShockEMCDimensions (W H D)without feetincluding feetWeightRecommended calibration intervalRohde & Schwarz R&S FPC1000 Spectrum Analyzer7

Version 01.00, December 2016Ordering informationDesignationSpectrum Analyzer, 9 kHz to 1 GHzAccessories suppliedPower cable, USB cable for connection to PCTypeR&S FPC1000Order No.1328.6660.02TypeR&S FPC-B2R&S FPC-B3R&S FPC-B22R&S FPC-K7R&S FPC-K43R&S FPC-K53R&S FPC-K55R&S FPC-B200Order ypeOrder gnationSpectrum Analyzer Frequency Upgrade to 2 GHzSpectrum Analyzer Frequency Upgrade to 3 GHzSpectrum Analyzer PreamplifierAnalog Modulation Analysis for AM, FM, ASK, FSKReceiver ModeAnalog Modulation Analysis for ASK, FSKAdvanced MeasurementsWiFi- SupportAccessoriesDesignation19" Rack Mount KitSoft Carrying BagCarrying CaseR&S ZZA-FPC1R&S RTM-Z3R&S RTB-Z3Service optionsWarrantyBase unitAll other items 1OptionsExtended Warranty, one yearExtended Warranty, two yearsExtended Warranty with Calibration Coverage, one yearExtended Warranty with Calibration Coverage, two years3 years1 yearR&S WE1R&S WE2R&S CW1R&S CW2Please contact your local Rohde& Schwarz sales office.Extended warranty with a term of one and two years (WE1 and WE2)Repairs carried out during the contract term are free of charge 2. Necessary calibration and adjustments carried out during repairs arealso covered.Extended warranty with calibration coverage (CW1 and CW2)Enhance your extended warranty by adding calibration coverage at a package price. This package ensures that yourRohde & Schwarz product is regularly calibrated, inspected and maintained during the term of the contract. It includes all repairs 2 andcalibration at the recommended intervals as well as any calibration carried out during repairs or option upgrades.For product brochure, see PD 5214.7112.12 and www.rohde-schwarz.com128For options that are installed, the remaining base unit warranty applies if longer than 1 year. Exception: all batteries have a 1 year warranty.Excluding defects caused by incorrect operation or handling and force majeure. Wear-and-tear parts are not included.Rohde & Schwarz R&S FPC1000 Spectrum Analyzer

Version 01.00, December 2016Rohde & Schwarz R&S FPC1000 Spectrum Analyzer9

Version 01.00, December 201610Rohde & Schwarz R&S FPC1000 Spectrum Analyzer