Transcription
Parker Indirect Fired Hot Water BoilerMfg: ParkerModel: WH-970Stock No. CGCB074.1Serial No.Parker Indirect Fired Hot Water Boiler. Model: WH-970. MAWP: 125 psi., heating surface: 103.5 sq. ft.Horse power input: 29 hp (boiler) (BTU input: 970,000), Horse power output: 23.2 hp (BTU output:776,000). Output 60 F rise: 1550 gph , Output 100 F rise: 930 gph.Recommended flow rate: 54 gpm. Alternating current motor, ½ hp, 1725 rpm, 115/230 V, 5.2/2.6 amps,60 Hz, 1 phase. Pump. (32) Burners: 5-1/2 in. L x 2 in. W. Honeywell gas modutrol motor, 120 V, 0.36amps 50 & 60 Hz, 27 watts. Parker electrical control panel. Temp/press. gauge: 60-320 F, 0-250psi. Steam outlet: 14 in. dia. Parker steel tank-100 gallons, manway: 22 in. L x 12 in. H (oval). Maximumtemperature: 450 F; thermometer: 30-230 F. Boiler inlet/outlet: 2-1/2 in. insulated pipe, pump pipe: 2 in.dia., gas pipe: ¾ in. dia., tank inlet/outlet: (2) 2-1/2 in. threaded female. Overall dimensions (boiler): 75 in.L x 45 in. W x 53 in. H. Overall dimensions (tank): 53 in. L x 40 in. W x 115 in. H.Parker electrical control panel, (2) switches: 1st boiler control, 2nd main burner, indicator light: controlpower, pilot on, level safe, limit safe, burner on.
INDIRECT HOT WATER SYSTEMHot WaterAssures Rust Free Hot Water, Economical & Reliablefor Low and High Temperature ApplicationsGas, Propane or Low NOx Fired Models 300,000 to 3,000,000 BTU Input209-11 Water HeatersIndirect Hot Water Heater System300,000 to 3,000,000 BTU InputTHE COMPLETE HOT WATERSYSTEM INCLUDES:The Parker Hot Water StorageTank is of quality construction built inaccordance with the ASME Code. Tanksare available vertical or horizontal ina wide range of sizes and include anattractive, durable exterior paintedfinish and an internal phenolic coating.Special warrantied internal tank liningsare available at nominal cost. A combination temperature-pressure gaugeand safety relief valve are furnishedwith the system.209-11 Water HeatersThe Parker Indirect Fired WaterHeater is an industrial quality unitdesigned for economically heatinglarge volumes of domestic or processwater for commercial and industrialapplications. The all bronze and copperheat transfer coil eliminates the possibility of rust throughout the water passages. The indirect principle of heatingthe process water with sealed-in primary water combined with controlledcirculation minimizes the possibility ofscaling within the heat transfer coil forlow or high temperature applications.The High Duty Circulator hasbronze-fitted construction, balancedcentrifugal impeller and mechanicalseal selected for each specific heatersize.PARKERB O I L E R C O.NEVER A COMPROMISE FOR QUALITY OR SAFETYA Packaged Piping Kit is alsoavailable and includes all the pipingand valves shown above to easily connect the heater to the storage tank.Stainless Steel Option is availableon the heater with 316 stainless steeltubes and all stainless waterwaysfor deionized or pure process waterapplications. Note: unit outputs arereduced, consult factory.5930 Bandini BoulevardLos Angeles CA 90040Fax (323) 722-2848www.parkerboiler.comPhone (323) 727-9800BROCHURE 209-11 0C2
PARKER INDIRECT HEATERSNatural Thermal CirculationGeneral InformationHot Water209-11 Water HeatersINDIRECT FIRED WATER HEATERSThe Parker WH Model Indirect FiredWater Heater is an excellent choice forLow or High Temperature applications.Typical Parker Indirect Hot Water Heater System for Hot Water ServiceExpansion Tank(If Required)Cold WaterStorage TankPressure & Temperature Relief ValveHot Water SupplyReturn Water Circulator209-11 Water HeatersTemp & PressureGagePressure &TemperatureRelief ValveIndirect Water HeaterCirculating PumpIndirect Heating PrincipleHotCirculating Process WaterColdBoiler TubesBoiler WaterUpper HeaderHeat Transfer CoilUses Include:LaundriesHotelsApartmentsFood ProcessingHospitalsSchoolsSwimming PoolsWater Source Heat PumpsLow Temperature ProcessWater ApplicationsPond HeatingFish FarmsRadiant HeatingThe Basic Principle of indirect heatingis accomplished by circulating the lowtemperature (or circulating process water)water through a copper tube heat transfercoil which is mounted internally andimmersed in the primary Boiler water. Theprimary Boiler water is contained ina Bent Steel Tube Bundle and is heatedin the furnace area, it rises to the upperheader where the heat transfer into thesecondary water occurs. The colder secondary water does not come into contactwith high furnace temperatures or intocontact with the flue gas at all.This eliminates any possibilityof flue gas condensation which will occuron Direct Fired Heaters. Sweating andexternal corrosion of the Boiler Structureand tubes is essentially eliminated. Thepossibilities of scale, rust and corrosion areminimized by the indirect design principle.The furnace remains at a steadyuniform temperature which results inhigh combustion efficiency and lower fuelconsumption. This principle has provenmore efficient and provides for a longerlife as opposed to a direct system.Burners5930 Bandini BoulevardLos Angeles CA 90040Fax (323) 722-2848www.parkerboiler.comPhone (323) 727-9800BROCHURE 209-11 0C2PARKERB O I L E R C O.
PARKER INDIRECT FIRED WATER HEATERWH300 TO WH 1410 - ATMOSPHERIC GAS FIREDNO.ABCDE1WA1WB2LA2LB3HA3HB3HC4A4B7A / 7A17A27B7B17H15&16SPEC. SHEET D-210-I7DMODEL NO. WH300 WH395 WH490 WH600 WH730 WH970 WH1210 WH14101000's BTU/HR. 300395490600730970121014101000's BTU/HR. 2403163924805847769681128SQ. FT. 41.5555566.577103.5127.5160G.P.H. 4806327839581167155019352253G.P.H. 39IN.4141414141414242IN.7173737575778282Height Overall Inclu. Baro. Damper (Vert. Outlet/Horizont. Outlet) - (Spec.Order)IN. 57/54 60/58 60/58 60/58 63/60 67/6368/6470/68Vent Stack Diameter with Draft Hood-(Standard)IN.810101212141616Vent Stack Diameter with Barometric DamperIN.688810121214Std. Nat. Gas Inlet Size/Supply Press; Max: 14" WC; Min.:7” WCIN.3/43/41111-1/21-1/21-1/2Nat. Gas Manifold Pressure at BurnerIN. WC44444444Hi Press. Nat. & Propane Gas Inlet Size/(Supply Press. 1-5 PSI)IN.3/43/43/43/43/41-1/21-1/21-1/2Propane Manifold Pressure at BurnerIN. WC1818181818181818Gas Inlet Height From FloorIN.55555566Exchanger Water Outlet and Inlet SizeIN. 1-1/21-1/21-1/21-1/21-1/222215H&16H Exchanger Water Outlet and Inlet Height From FloorIN.343434343434353515&16CS Outlet & Inlet Size for Closed System HeatingIN.2222222-1/22-1/218AHP Safety Relief Valve Drain Size- 125 PSIOUTLET IN.3/43/43/43/43/43/43/43/418ALPSafety Relief Valve Drain Size- 30 PSIOUTLET IN.3/411111¼1¼1½JWater CapacityGAL.8.511111315192125KNet Weight of BoilerLBS. 62579079010951360159017802100LDomestic Crated Shipping Weight of BoilerLBS. 71588589512051485172019202250MINIMUM LISTED CLEARANCES TO12"48"6"12"COMBUSTIBLE CONSTRUCTION:Cabinet Sides & RearCabinet TopDraft Hood Vent ConnectorBaro. Damper Chimney ConnectorRecommended Clearances for Access: Inspection Doors 18";Front (Cabinet Width 1WA 10” For Exchanger Removal); Controls 24"; ElectricalPanel 30"; Additional Space may be required by Local CodesNote: All of the above dimensions are for a standard trim model. Due to continuous improvements, specifications are subject to change without notice.BTU InputBTU OutputHeating SurfaceOutput - 60 Degree RiseOutput - 100 Degree RiseWidth of Cabinet OnlyWidth Overall Including ControlsLength of Cabinet OnlyLength OverallHeight of Cabinet OnlyHeight Overall Including Draft Hood - (Standard)D-210-i.DOC
SPEC. SHEET D-210-17DPARKER INDIRECT FIRED WATER HEATERWH1900 TO WH3000 - ATMOSPHERICNO.ABCDE1WA1WB2LA2LB3HA3HB3HC4A4B7A/ 7A17A27B7B17H15&16MODEL NO. WH1900WH2270WH2650WH3000BTU Input1000's BTU/HR.1900227026503000BTU Output1000's BTU/HR.1520181621202400Heating SurfaceSQ. FT.208251287331Output - 60 Degree RiseG.P.H.3037362842374797Output - 100 Degree RiseG.P.H.1822217725422878Width of Cabinet OnlyIN.40465259Width Overall Including ControlsIN.63717582Length of Cabinet OnlyIN.54545454Length OverallIN.54545454Height of Cabinet OnlyIN.53535353Height Overall Including Draft Hood - (Standard)IN.979999101Height Overall Including Baro. Damper (Vert. Outlet/Horizont. Outlet) - (Special Order)IN. 83 / 8283 / 8287 / 8487 / 84Vent Stack Diameter with Draft Hood - (Standard)IN.20222224Vent Stack Diameter with Barometric DamperIN.16161818Std. Nat. Gas Inlet Size / Supply Press; Max: 14" WC; Min.: 7” WCIN.2222Nat. Gas Manifold Pressure at BurnerIN. WC4444Hi Press. Nat. & Propane Gas Inlet Size (Supply Press. 1-5 PSI)IN.1-1/21-1/21-1/21-1/2Propane Manifold Pressure at Burner:IN. WC18181818Gas Inlet Height From FloorIN.5555Exchanger Water Outlet and Inlet SizeIN.2-1/22-1/22-1/22-1/215H&16HExchanger Water Outlet and Inlet Height From FloorIN.4444444415&16CSOutlet & Inlet Size for Closed System HeatingIN.333317DDrain OpeningIN.1-1/41-1/21-1/21-1/218AHPSafety Relief Valve Drain Size- 125 PSIOUTLET IN.1111-1/418ALPSafety Relief Valve Drain Size- 30 PSIOUTLET IN.1-1/2222JWater CapacityGAL.30354050KNet Weight of BoilerLBS.2695315035753940LDomestic Crated Shipping Weight of BoilerLBS.2945345039254380MINIMUM LISTED CLEARANCES TO12"48"6"12"COMBUSTIBLE CONSTRUCTION:Cabinet Sides & RearCabinet TopDraft Hood Vent ConnectorBaro. Damper Chimney ConnectorRecommended Clearances for Access: Inspection Doors 18"; Front (Cabinet Width 1WA 10” For Exchanger Removal); Controls 24"; ElectricalPanel 30"; Additional Space may be required by Local CodesNote: All of the above dimensions are for a standard trim model. Due to continuous improvement, specifications are subject to change without noticeD-210-i.DOC
PARKER BOILER CO. 5930 Bandini Boulevard Los Angeles CA 90040 Fax (323) 722-2848 www.parkerboiler.com Phone (323) 727-9800 BROCHURE 209-11 0C2!FK08K I 209-11 Water Heaters Indirect Hot Water Heater System 300,000 to 3,000,000 BTU Input THE COMPLETE HOT WATER SYSTEM INCLUDES: The Parker Indirect Fired Water Heater is an industrial quality unit
