Transcription
Designedaround your life
ContentsImportant InformationProduct Information/RegistrationSafety WarningsCar Seat Use after a CrashVehicle CompatibilityWARNING: Carefully read and understandall instructions and warnings in this manual,and those labeled on your Child Restraint.Failure to do so can result in the SERIOUSINJURY or DEATH of your child. Store manualin pocket at rear of base for future use.2RAVA instructions4689Child Restraint OverviewFeatures OverviewFeatures UsageChild Usage Requirements161840Rear Facing InstallationRear Facing SetupUsing Vehicle Lap/Shoulder BeltUsing Lower Anchor BeltUsing Vehicle Lap Belt42444648Forward Facing InstallationForward Facing SetupUsing Vehicle Lap/Shoulder BeltUsing Lower Anchor BeltUsing Vehicle Lap Belt50525456Securing Child in Child Restraint58Aircraft Installation61Cleaning and Maintenance62RAVA instructions3
Product Information/RegistrationModel Number:Manufactured in (date):Product RegistrationPlease fill in the above information. The modelnumber and the manufactured in date are located ona label on the bottom of your child restraint. Fill outthe prepaid registration postcard attached to theseat pad and mail it today.Child restraints could be recalled for safety reasons.You must register this restraint to be reached in arecall. Send your name, address, e-mail address ifavailable and the Child Restraint’s model numberand manufacturing date to:Nuna Baby Essentials Inc.70 Thousand Oaks Blvd.Morgantown, PA 19543WarrantyWe have purposely designed our high-qualityproducts so that they can grow with both your childand your family. Because we stand by our product,our gear is covered by a custom warranty perproduct, starting from the day it was purchased.Please have the proof of purchase, model numberand manufactured in date available when youcontact us.For warranty information please visit:www.nunababy.com/warrantyContactFor replacement parts, service, or additionalwarranty questions, please contact our customerservice department.In the .USAor call 1.855.NUNA.USAor register online at:www.nunababy.comClick on the “Register Car Seat” link on the homepage.Recall InformationFor recall information, call the U.S. Government’sVehicle Safety Hotline at: 1.888.327.4236(TTY: 1.800.424.9153) or go tohttp://www.NHTSA.gov4RAVA instructionsRAVA instructions5
WARNINGDEATH OR SERIOUS INJURY CAN OCCUR,Never leave child unattended in this ChildRestraint.Do not allow anyone who has not read theInstructions to install or use this ChildRestraint.Never leave Child Restraint unsecured inyour vehicle even when it is unoccupied. Ina crash, it could become a projectile andinjure other vehicle occupants.To avoid strangulation, do not allowchildren to play with vehicle or ChildRestraint belts or straps. If possible, moveunused belts out of reach.Cover the Child Restraint when yourvehicle is parked in sunlight. Parts of aChild Restraint can become very hot ifleft in the sun, and can burn a child’s skin.Check for hot parts before putting yourchild in the Child Restraint.6RAVA instructionsDo not use any products or accessorieswith this Child Restraint unless they areapproved by Nuna USA for use with thisChild Restraint. Doing so may be unsafeand may void the warranty.Do not use Child Restraint if it has frayedor cut harness straps, or is damaged inany way. To find out if damaged parts arereplaceable, call 1-855-NUNA-USA.Never modify any part of the ChildRestraint.NEVER use a car seat that has beeninvolved in a moderate to severe crash.See page 8 to learn the differencebetween a minor and moderate to severecrash.Do not use Child Restraint if it is more than10 years old. Check the manufacturer slabel or stamped ‘do not use after’ date onthe bottom of the Child Restraint Base.RAVA instructions7
Car Seat Use after a CrashThe National Highway Traffic Safety Administration(NHTSA) recommends that car seats be replacedfollowing a moderate or severe crash. Car seatsdo not automatically need to be replaced followinga minor crash.A minor crash is one in which ALL of these apply: The vehicle was able to be driven away fromthe crash site. The vehicle door nearest to the car seat wasnot damaged. None of the passengers in the vehiclesustained any injuries in the crash. If the vehicle has air bags, none of the air bagsdeployed during the crash; and There is no visible damage to the car seat.Vehicle CompatibilityWARNING: You MUST read and understandALL Child Restraint related instructions andwarnings in your vehicle owner’s manual tocorrectly and safely use this Child Restraint inyour vehicle.This Child Restraint can ONLY be installed onvehicle seats that face forward. DO NOT install inseats that face to the sides or rear of the vehicle.Any crash that does not meet all of the abovecriteria for a minor crash is considered a moderateto severe crash. NEVER use a car seat that hasbeen involved in a moderate to severe crash.Information from nhtsa.govWARNING: SERIOUS INJURYOR DEATH MAY OCCUR.NEVER install this Child Restraintrear facing in a vehicle seatingposition with a frontal air bag unlessit is turned off. If your vehicle isequipped with front passenger side air bags,check your vehicle owner's manual for ChildRestraint installation instructions.8RAVA instructionsRAVA instructions9
IMPORTANT: According to accident statistics,children are safer when properly restrainedin the rear seating positions than in the frontseating positions.11”This Child Restraint can be installed without vehiclebelts, by connecting the Restraint’s Lower AnchorBelts to the lower anchorages in your vehicle.LATCH (Lower Anchors and Tether for CHildren) isa system for installing a Child Restraint in a vehiclewithout using the vehicle belts. Refer to yourvehicle owner’s manual to determine if your vehicleis equipped with LATCH, and how to correctly useLATCH to install this Child Restraint in your vehicle.Lower Anchor andTop Tether AnchorLocationsVehicle Top TetherAnchor PointsWARNING: DO NOT USE the LATCH loweranchor belts to attach this Child Restraintrear facing when restraining a child weighingover 35 lb (15.8 kg) or forward facing whenrestraining a child weighing over 40 lb(18.1 kg). Check your vehicle owner’s manualfor Tether Anchor weight limits.The Restraint’s Tether Strap should be used forALL Forward Facing Installations, as it provides amore secure installation.Rear ShelfVehicle LowerAnchor PointsThis Child Restraint is designed to be used withlower LATCH anchors at the standard spacing of11 inches (28 cm). LATCH lower vehicle anchorpoints are defined as 11 inches (28 cm) from thecenter of one LATCH anchor to the center ofanother LATCH anchor.10RAVA instructionsBack WallBack of SeatVehicle FloorWARNING: NEVER use a Child Restraintin a vehicle seating position where it cannot becorrectly secured. An incorrectly installed ChildRestraint will not protect your child in a crash.RAVA instructions11
The following types of vehicle belts CAN BE USEDto install this Child Restraint.121 - Lap/Shoulder Belt2 - Lap Belt OnlyBelts MUST be able to be locked.Refer to vehicle owner's manual to determine if thebelts in your vehicle lock by switching the seatbelt's retractor or they have a locking latch platethat locks the vehicle's seat belts so they will notmove freely.If the belt cannot be locked using one of thesemethods, contact Nuna Customer Service for alocking clip.12RAVA instructionsRAVA instructions13
Vehicle belts that CANNOT BE USED with yourchild restraint:142536The following types of vehicle belts MUST NOTbe used to install this Child Restraint. They will notprovide a secure, safe installation. Refer to yourvehicle owner’s manual for which seating positionsin your vehicle can be used to install this ChildRestraint using vehicle belts or LATCH.1 - Motorized Belts (Automatic)2-3-456-14These should not be used unless the shoulderbelt can be removed, the lap belt is locked anduse is allowed by the vehicle manufacturer.Dual Retractor Lap/Shoulder BeltsIf allowed by the manufacturer, the lap belt onlymay be used to secure the child restraint inaccordance with this manual and the vehicle’smanual.Non-Locking (ELR) Lap BeltsThis belt locks in a crash or sudden stop andshould only be used with a belt shortening clip.Contact your vehicle manufacturer if needed.Airbag/Inflatable BeltsThis belt cannot be used to install this childrestraint.Door Mounted BeltsThis belt cannot be used to install this childrestraint.Lap Belts forward of Seat BightThis belt (where the seat bottom and backmeet) cannot be used to install this childrestraint.RAVA instructionsRAVA instructions15
Features Overview1234567891011121314Shoulder HarnessPadsHarness BuckleCrotch PadHarness ReleaseButtonHarness Adjuster StrapCalf SupportCup HolderHip Harness PadsBuckle Tongue HolderChest ClipInfant InsertHead InsertHead SupportHarness Strap1211123109251315 Seat Cover16 Lower Anchor BeltStorage(underneath door)17 Recline PositionIndicator18 Recline Button19 Rear Facing TrueTension Door20 Crotch Belt Plate21 Rear Facing TrueTension Button22 Forward Facing TrueTension Button23 Forward Facing TrueTension Door27824 Side ImpactProtection (SIP)pods25 Head SupportButton26 Tether StrapAdjuster27 Tether Strap28 Tether Hook29 Lower Anchor Belt30 Lower AnchorConnectors31 Instruction ManualStorage32 Lower AnchorAdjuster2642875142461523222116182016RAVA instructions19322930301731RAVA instructions17
Feature Usage1425Harness Use1 - To Loosen HarnessPress on Harness Release Button while pullingforward on the Harness Straps.2 - To Open Chest ClipPress button on front of Clip and pull Clipapart.3 - To Open Harness BucklePress red button on front of Buckle and pull outBuckle Tongues.4 - To Use Buckle Tongue HoldersLoosen and unfasten harness. Place BuckleTongues in Holders.1125 - To Fasten Chest ClipPush Chest Clip halves together until they click.Pull to check. (1)To Fasten BuckleInsert Buckle Tongues firmly into Buckle untilthey click. Pull up on Tongues to ensure theyare locked. (2)366 - To Tighten HarnessPull on Harness Adjuster Strap.18RAVA instructionsRAVA instructions19
Head Insert Use1 - The Head Insert may be used or removed for1improved comfort or fit of any child.Harness & Crotch Pad Use2 - The Harness Pads are a comfort feature thatmay be used or removed for any child. Smallinfants may have better fit to Harness withShoulder Pads removed.Head Support Adjustment3 - With Harness loose (p.18), squeeze Head2Support Button and move Head Support up ordown to desired position.Release button and slide Head Support slightlyup or down to lock into appropriate useposition.320 RAVA instructionsRAVA instructions21
Infant Insert UseThe infant insert can be used for a child that isbetween 5–11 lb to improve the harness fit andrecline angle for smaller infants.1324You MUST use the infant insert if the harnessstraps are positioned ABOVE the child’s shouldersand child weighs between 5–11 lb. The harnessMUST be positioned AT or JUST BELOW the child’sshoulders.The head insert may be used or removed forimproved comfort to child at any time.To Install Infant Insert1 - Pull Harness Buckle through slot in the bottomof Infant Insert.2 - Route Harness Straps through gaps in sides ofInfant Insert.3 - Push Infant Insert firmly into Child Restraint.4 - Make sure insert is properly positioned.When properly installed, the Infant Insert willnot interfere with Harness Straps or CrotchBelt. Crotch Belt must be locked in innerposition when Infant Insert is used.22 RAVA instructionsRAVA instructions 23
True Tension Door Use1324This Child Restraint has 2 True Tension Doorsthat aid in a simple and secure installation of theChild Restraint in your vehicle. They are locatedunderneath the Seat Cover. The upper Door (RED)is for forward facing use, and the lower Door(BLUE) is for rear facing use.Remove Infant Insert, loosen and unfasten Harness(p.18), and retain with Buckle Tongue Holders (p.18).1 - Adjust Head Support to highest position,unsnap Seat Cover and pull to front of seat.2 - Squeeze Door release button for theappropriate True Tension Door.3 - Lift open True Tension Door.4 - Close True Tension Door by pressing downfirmly on Door until both latches lock in place.Replace Seat Cover and reinstall Infant Insert ifused (p.22).24 RAVA instructionsRAVA instructions 25
Crotch Belt Adjustment12The Crotch Belt has two positions. Use the positionthat is closest to, but not under your child.Remove Infant Insert (p.22) and loosen andunbuckle Harness (p.18).1 - Unsnap Seat Cover and pull forward whilepush & slidepulling crotch buckle through slot in SeatCover.2 - Depress and slide Crotch Belt plate forward orbackward and lock in desired position. Placebuckle back through correct slot in Seat Coverand replace Seat Cover and Infant Insert (ifusing).26 RAVA instructionsRAVA instructions27
Lower Anchor Belt Storage and UseThe Lower Anchor Belt, located in StorageCompartment under the Rear Facing True TensionDoor, can be used instead of a vehicle belt to installthis Child Restraint. The Lower Anchor Beltmust not be used rear facing if your child weighsmore than 35 lb (15.8 kg), or forward facing if yourchild weighs more than 40 lb (18.1 kg).13241 - To use Lower Anchor Belt, open Rear FacingTrue Tension Door (p.24), remove LowerAnchor Belt, and lengthen by pressing adjusterbutton while pulling on Belt.2 - To connect Lower Anchor Belt to lower anchorsin vehicle, press Connector firmly onto loweranchor and pull to check.3 - To release Lower Anchor Belt, press red buttonon end of Connector while pulling on Belt.4 - To store, fold Lower Anchor Adjuster andLower Anchor Belt, and place in StorageCompartment. Store other Lower Anchor Beltin adjacent Storage Compartment. Tuck excesswebbing.When not in use, the Lower Anchor Belt MUSTbe properly stored in Lower Anchor StorageCompartment under Rear Facing True TensionDoor, and MUST NOT interfere with latching ofDoor.28 RAVA instructionsRAVA instructions 29
Cup Holder Use1 - Pivot Cup Holder up and lock in use position.2 - Push center of Cup Holder down to extend to1324opened position.3 - While in the opened position, pull up on theCup Holder to remove for washing OR removefor easier Rear Facing Belt Installation.4 - To store, collapse Cup Holder and pivot down.Cup Holders must be opened to access BeltPath during Rear Facing Installation of ChildRestraint. Cup Holders may be collapsed downagainst vehicle belt after belt installation.DO NOT place glass or metal containers or hardor sharp objects in Cup Holder. In a crash theycould cause serious injury.30 RAVA instructionsRAVA instructions31
Side Impact Protection (SIP) UseSIP pods should only be used on the door side ofthe child restraint. If the child restraint is installedin the middle seat position the SIP pods should notbe used.121 - Pull out SIP Pod from corner of stored positionuntil it locks into position.2 - To store, press button and push SIP Pod intostored position.32 RAVA instructionsRAVA instructions 33
Calf Support UseThe Calf Support may be used to give your childmore leg room or improve installation when rearfacing and provide improved comfort when forwardfacing. It is designed to change position withoutdamage if excessive force is applied.11 2 3 4 55 4 3 2 11 - Recline Child Restraint to rear facing position 1(BLUE).2 - Move Calf Support to USE position by reachingunder front of Child Restraint and rotating CalfSupport down and forward.3 - Move Calf Support to STORAGE position by2pulling down on Calf Support to unlock, androtating it to storage position.When used rear facing for children over 40 lb,Calf Support should be in the use position.2131234 RAVA instructionsRAVA instructions 35
Tether Use1 - To use, remove Tether by loosening strap and1unclipping from storage anchor.2 - To extend Tether for use, tilt Tether Adjusterand pull to lengthen.3 - To store, attach Tether to storage anchor andremove slack in strap by pulling on free end ofstrap. Loose strap should be stored in providedtether cover. When not in use, Tether MUST beproperly stored.WARNING: ALWAYS USE TETHER forforward facing installation if vehicle is equippedwith a Tether Anchor point and vehiclerequirements are met (see vehicle owner'smanual). NEVER USE IN REAR FACINGINSTALLATION.2336 RAVA instructionsRAVA instructions37
Recline UseThis Child Restraint has 10 recline positions.Recline can be changed for child's comfort or toimprove installation of Child Restraint.11 - Positions 1–5 (BLUE) are for rear facing usewith children 5–50 lb.1 2 3 4 5If infant’s head falls forward, Child Restraintmust be reclined more. Use Infant Insert withinfants 5–11 lb (2.3–5 kg) to improve the reclineangle for smaller infants.2 - Positions 1–5 (RED) are for forward facing use5 4 3 2 12with children 25–65 lb.To Adjust Recline3 - Press Recline Button (1) on either side of the1 2 3 4 5Child Restraint and move seat to desiredrecline position. (2)5 4 3 2 1Release Recline Button, and check that ChildRestraint is locked in desired recline position.To change recline position after installation,uninstall Child Restraint, select new reclineposition, and reinstall Child Restraint.32138 RAVA instructionsRAVA instructions 39
Child Usage RequirementsTo use this Child Restraint, your child mustmeet ALL of the following weight and heightrequirements below:Height: 49 in (124 cm) or lessThe Infant Insert (p.22) is only for use with infantswho weigh between 5–11 lb (2.3–5 kg).Rear Facing Installationrecommended up to 2 years (5–50 lb)vehicle beltORlower anchor belt50 lb(22.6 kg)recommended up to 2 years or older (5–50 lb)vehicle beltORlower anchor beltWeight: 5-65 lb (2.3–29.4 kg)infantinsert5 lb11 lb 25 lb35 lb40 lb(2.3 kg) (5 kg) (11.3 kg) (15.8 kg) (18.1 kg)Rear Facing Installationinfantinsert5 lb11 lb 25 lb35 lb(2.3 kg) (5 kg) (11.3 kg) (15.8 kg)50 lb(22.6 kg)65 lb(29.4 kg)The American Academy of Pediatricsrecommends children should ride rear facingfor as long as possible up to 2 years in age, oruntil they reach maximum height and weight fortheir seat.65 lb(29.4 kg)lower anchor beltORvehicle belt & tether strapTether strap should always beused in Forward Facing Installation.Forward Facing Installationrecommended 2 years or older (25–65 lb)WARNING: Use either vehicle seat belt orLower Anchors. Never use both methods toinstall Child Restraint.40 RAVA instructionsRAVA instructions41
Rear Facing SetupBefore install, store tether strap.1Move Calf Support to desired installation position(p.34).1 - Place Child Restraint rear facing in acompatible vehicle seat (p.8).2 - Select desired rear facing recline position 1–5(BLUE) (p.38).If infant’s head falls forward, Child Restraintmust be reclined more. Use Infant Insert withinfants 5–11 lb (2.3–5 kg) to improve the reclineangle for smaller infants.2Loosen and unbuckle Harness and retain withBuckle Tongue Holders (p.18).1 2 3 4 55 4 3 2 1Pivot Cup Holders to USE position to accessRear Facing Belt Path (p.30). If desired, cupholderscan be removed for easier access to Rear FacingBelt Path.3 - Remove Infant Insert, lift lower Seat Cover, andopen Rear Facing True Tension Door (p.24).Complete installation using your vehicle’s Lap/Shoulder Belt (p.44), the Lower Anchor Belt (p.46),or a compatible vehicle Lap Belt (p.48).42 RAVA instructions3RAVA instructions 43
Using Vehicle Lap/Shoulder Belt(preferred installation method)1 - Route vehicle Lap/Shoulder belt through BLUERear Facing Belt Path and buckle vehicle Lap/Shoulder Belt. Vehicle belt must be routedunder True Tension Door. (1)1221Remove all slack from the vehicle belt system toproperly secure this child restraint. (2) Lockvehicle belt (refer to vehicle owner's manual).2 Close True Tension Door and replace SeatCover and Infant Insert (if used).Test by pulling on shoulder belt to ensure it islocked.To open True Tension Door, unbuckle vehicle beltand push down slightly on door to release tension.WARNING: Check that Child Restraint issecurely installed before each use.Check InstallationSeat is in appropriate rear facing recline position.Seat is securely installed. Hold seat near rearfacing belt path and move seat side to side, frontto back, and up and down. Seat should moveless than 1 inch.Tether strap is not used for Rear FacingInstallation and must be secured in storagelocation on back of Child Restraint.Cup Holders may be placed in any position afterinstallation.44 RAVA instructionsRAVA instructions 45
Using Lower Anchor Belt1324WARNING: Do not install by this method fora child weighing more than 35 lb (15.8 kg).1 - Remove Lower Anchor Belt from StorageCompartment (p.28) and route through BLUERear Facing Belt Path under Cup Holder.2 - Lengthen Lower Anchor Belt as necessary (p.28)and attach to Lower Anchor points in vehicle.3 - Remove all slack from Lower Anchor Belt bypulling loop at end of Belt.4 - Close True Tension Door and replace SeatCover and Infant Insert (if used). Pull crotchbelt through slot.To open True Tension Door, unbuckle vehicle beltand push down slightly on door to release tension.WARNING: Check that Child Restraint issecurely installed before each use.Check InstallationSeat is in appropriate rear facing reclineposition.Seat is securely installed. Hold seat near rearfacing belt path and move seat side to side, frontto back, and up and down. Seat should moveless than 1 inch.Tether strap is not used for Rear FacingInstallation and must be secured in storagelocation on back of Child Restraint.Cup Holders may be placed in any position afterinstallation.46 RAVA instructionsRAVA instructions47
Using Vehicle Lap Belt1 - Route vehicle Lap belt through BLUE Rear21Facing Belt Path and buckle vehicle Lap Belt. (1)2Remove all slack from vehicle Lap Belt. (2)Lock vehicle belt (refer to vehicle owner'smanual).2 - Close True Tension Door and replace SeatCover and Infant Insert (if used).1To open True Tension Door, unbuckle vehicle beltand push down slightly on door to release tension.WARNING: Check that Child Restraint issecurely installed before each use.Check InstallationSeat is in appropriate rear facing reclineposition.Seat is securely installed. Hold seat near rearfacing belt path and move seat side to side, frontto back, and up and down. Seat should moveless than 1 inch.Tether strap is not used for Rear FacingInstallation and must be secured in storagelocation on back of Child Restraint.Cup Holders may be placed in any position afterinstallation.48 RAVA instructionsRAVA instructions 49
Forward Facing Installationrecommended 2 years or older (25–65 lb)5 lb11 lb 25 lb35 lb40 lb(2.3 kg) (5 kg) (11.3 kg) (15.8 kg) (18.1 kg)50 lb(22.6 kg)165 lb(29.4 kg)lower anchor beltORvehicle belt & tether strapTether strap should always beused in Forward Facing Installation.Forward Facing SetupRemove Tether from storage location and lengthenfor use (p.36).1Place Child Restraint forward facing in acompatible vehicle seat (p.8).21 2 3 4 55 4 3 2 12 Select desired forward facing recline position1–5 (RED) (p.38).Loosen and unbuckle harness and retain withBuckle Tongue Holders (p.18).3 Fully raise Head Support, lift Seat Cover, andopen Forward Facing True Tension Door (p.24).3Complete installation using your vehicle’s Lap/Shoulder Belt (p.52), the Lower Anchor Belt (p.54),or a compatible vehicle Lap Belt (p.56).50 RAVA instructionsRAVA instructions51
Using Vehicle Lap/Shoulder Belt(preferred installation method)13241 - Route vehicle Lap/Shoulder belt through REDForward Facing Belt Path and buckle vehicleLap/Shoulder Belt.2 - Remove all slack from the vehicle belt systemto properly secure this child restraint. (1) Lockvehicle belt (refer to vehicle owner's manual).Close True Tension Door and replace Seat Cover.Test by pulling on shoulder belt to ensure it islocked.3 - Attach Tether Hook to Tether Anchor on vehicleand tighten (p.36).4 - Tuck excess webbing behind Child Restraint.To open True Tension Door, unbuckle vehicle beltand push down slightly on door to release tension.21WARNING: Check that Child Restraint issecurely installed before each use.Check InstallationSeat is in appropriate forward facing reclineposition.Seat is securely installed. Hold seat nearforward facing Belt Path and move seat sideto side, front to back, and up and down. Seatshould move less than 1 inch.Tether is properly used and attached to vehicleTether Anchor.52 RAVA instructionsRAVA instructions 53
Using Lower Anchor Belt1324WARNING: Do not install by this method fora child weighing more than 40 lb (18.1 kg).1 - Remove Lower Anchor Belt from StorageCompartment (p.28), move along metal rod,and route through RED Forward Facing BeltPath.2 - Lengthen Lower Anchor Belt as necessary (p.28)and attach to Lower Anchor points in vehicle.3 - Remove all slack from Lower Anchor Belt bypulling loop at end of Belt straight back fromLatch Connector. Close True Tension Door andreplace Seat Cover.4 - Attach Tether Hook to Tether Anchor on vehicleand tighten (p.36). Tuck excess webbingbehind Child Restraint.To open True Tension Door, unbuckle vehicle beltand push down slightly on door to release tension.WARNING: Check that Child Restraint issecurely installed before each use.Check InstallationSeat is in appropriate forward facing reclineposition.Seat is securely installed. Hold seat nearforward facing Belt Path and move seat sideto side, front to back, and up and down. Seatshould move less than 1 inch.Tether is properly used and attached to vehicleTether Anchor.54 RAVA instructionsRAVA instructions55
Using Vehicle Lap Belt1 - Route vehicle Lap Belt through RED Forward-1Facing Belt Path and buckle vehicle Lap belt.2 - Remove all slack from vehicle Lap Belt. (1) Lockvehicle belt (refer to vehicle owner's manual).Close True Tension Door and replace Seat Cover.3 - Attach Tether Hook to Tether Anchor on vehicleand tighten (p.36). Tuck excess webbingbehind Child Restraint.To open True Tension Door, unbuckle vehicle beltand push down slightly on door to release tension.2WARNING: Check that Child Restraint issecurely installed before each use.Check InstallationSeat is in appropriate forward facing reclineposition.Seat is securely installed. Hold seat nearforward facing Belt Path and move seat sideto side, front to back, and up and down. Seatshould move less than 1 inch.Tether is properly used and attached to vehicleTether Anchor.56 RAVA instructions3RAVA instructions57
Securing Child inChild Restraint1WARNING: If your child is not properlysecured in the Child Restraint, they may beejected in a crash, resulting in serious injury ordeath.Loosen and unfasten Harness. Retain with BuckleTongue Holders (p.18).1 - Place child in Child Restraint with child’s backflat against Child Restraint seat back.2DO NOT allow child to slouch.2 - For rear facing use, adjust Head Support (p.20)to position harness AT or just below shoulders.For forward facing use, adjust Head Support(p.20) to position harness AT or just aboveshoulders.Rear Facing:Harness AT or justbelow shouldersBottom of Head Support should be close to, butnot compressing, child's shoulders.Adjust Crotch Belt to fit child (p.26). Crotch Beltshould be close to, but not under child.Position harness over child’s shoulders and aroundchild’s waist, and buckle harness.3 - Tighten harness (p.18) to fit snugly on child’sForward Facing:Harness AT orjust above shoulders312shoulders and thighs. It is snug if you cannotpinch a fold in the strap (1).Fasten and position Chest Clip (p.18) level withchild’s armpits (2).58 RAVA instructionsRAVA instructions 59
Secure Child ChecklistWARNING: Before securing child in therestraint, always check that Child Restraint isproperly installed.Harness straps are at correct height.Rear Facing: AT or just below child’s shouldersForward Facing: AT or just above child’sshouldersUse Infant Insert with infants 5–11 lb (2.3-5kg) to improve fit to seat and harness and toimprove the recline angle for smaller infants.Recline angle is appropriate for Child.If infant’s head falls forward, Child Restraintmust be reclined more. Use Infant Insertwith infants 5–11 lb (2.3–5 kg) to improve therecline angle for smaller infants.Aircraft InstallationThe FAA recommends that children up to 40 lb(18.1 kg) use a Child Restraint while travellingon an aircraft.This Child Restraint is certified for use on aircraft.Contact your airline about their policies prior totravel.Install Child Restraint rear facing orforward facing in a forward facing aircraftseat following “Using Vehicle Lap Belt”instructions, but install aircraft belt on topof closed True Tension Door and underSeat Cover.Head Support is locked in one of the 10 positions.Harness Buckle is securely fastened. Pull to check!Harness Straps are snug and flat on shouldersand thighs.A snug strap should not allow any slack. It liesin a relatively straight line without sagging. Itdoes not press on the child's flesh or push thechild's body into an unnatural position.WARNING: Child cannot be properlysecured in Child Restraint when wearingbulky clothing or wrapped in a blanket. Forwarmth, add blanket after properly securingChild in the Child Restraint.Chest Clip is fastened and at Child’s armpit level.60 RAVA instructionsRAVA instructions61
Cleaning and MaintenanceWARNING: Do not attempt to disassemblethe Child Restraint. Only perform steps shownin this manual.1bcedSeat Cover Removal1 - To remove seat pad:a Recline Child Restraint to rear facing position1 (BLUE).b Set Head Support in highest position.c Loosen and unbuckle Harness and Chest Clip.d Fully extend Calf Support.e Remove Tether from Storage Anchor.aRemove Harness/Buckle Pads as well as Infantand Head Inserts.Take care when removing Head Support Coverso as not to damage the energy absorbingfoam.62 RAVA instructionsRAVA instructions 63
1 - Remove Head Support Cover.a Grasp Head Support Cover at top behindHead Support Button.1a4b Peel Cover off
1 - Lap/Shoulder Belt 2 - Lap Belt Only Belts MUSTbe able to be locked. Refer to vehicle owner's manual to determine if the belts in your vehicle lock by switching the seat belt's retractor or they have a locking latch plate that loc
