Transcription
558 Federal Road, Brookfield, CT 06804O. (203) 885-0627 F. (203) 740-2441sheetmetal@mywinair.com www.mywinair.com2019SHEET METALFABRICATION STANDARDS
558 Federal Road, Brookfield, CT 06804O. (203) 885-0627 F. (203) 740-2441sheetmetal@mywinair.com www.mywinair.com5ft Joints1 in. Wg StaticPos. or Neg.Joints/Reinf.Duct Dimension(in.)Min. GAJointReinf.Mid RN/RN/RN/RJTR2-JTRN/RN/RN/RMPTMPT2-MPTLockMin. GAConnectionJoint ITTSPITTSS&DTDCTDCTDCTDCDuctmate6056565656605ft Coil/Sheet Stock/ (TDC/TDF) Duct Reinforcement ¾ Tie-RodsUSA Steel G90Ductmate connections: Any duct larger than 96”N/RN/AJTRMPT-Not Required-Not Applicable-Joint Tie Rod-Mid Panel Tie Rod(s)
558 Federal Road, Brookfield, CT 06804O. (203) 885-0627 F. (203) 740-2441sheetmetal@mywinair.com www.mywinair.com5ft Joints2 in. Wg StaticPos. or Neg.Joints/Reinf.Duct Dimension(in.)Min. GAJointReinf.Mid MPTLockMin. GAConnectionJoint Reinf.ConnectionSpacingReinf.PITTSPITTSPITTSPITTSL PITTSL PITTSL PITTSS&DTDCTDCTDCTDCTDCDuctmate595656565656605ft Coil/Sheet Stock/ (TDC/TDF) Duct Reinforcement ¾ Tie-RodsUSA Steel G90Ductmate connections: Any duct larger than 96”N/RN/AJTRMPT-Not Required-Not Applicable-Joint Tie Rod-Mid Panel Tie Rod(s)
558 Federal Road, Brookfield, CT 06804O. (203) 885-0627 F. (203) 740-2441sheetmetal@mywinair.com www.mywinair.com5ft Joints4 in. Wg StaticPos. or Neg.Joints/Reinf.Duct Dimension(in.)Min. 20181616N/RN/RN/RN/RN/RJTRJTRMid PanelReinf.N/RN/RN/RMPTMPTMPTMPTLockMin. GAConnectionJoint Reinf.ConnectionSpacingReinf.PITTSPITTSPITTSPITTSL PITTSL PITTSL 5ft Coil/Sheet Stock/ (TDC/TDF) Duct Reinforcement ¾ Tie-RodsUSA Steel G90Ductmate connections: Any duct larger than 96”N/RN/AJTRMPT-Not Required-Not Applicable-Joint Tie Rod-Mid Panel Tie Rod(s)
558 Federal Road, Brookfield, CT 06804O. (203) 885-0627 F. (203) 740-2441sheetmetal@mywinair.com www.mywinair.comInside of DuctPITTSBURGH SEAMLarge: 1-1/4” AllowanceSmall: 1” Allowance
Sheet Metal Fabrication(203)885-0627558 Federal Rd, Brookfield, CT 06804Place orders at sheetmetal@mywinair.comOval Spiral Duct 16 / 617 / 817 / 1018 / 1221 / 1420 / 1625 / 1819 / 620 / 820 / 1022 / 1224 / 1423 / 1628 / 1822 / 624 / 823 / 1025 / 1227 / 1426 / 1631 / 1825 / 627 / 826 / 1028 / 1230 / 1429 / 1634 / 1818 / 630 / 829 / 1031 / 1233 / 1432 / 1637 / 1831 / 633 / 832 / 1034 / 1236 / 1435 / 1640 / 1834 / 637 / 835 / 1037 / 1239 / 1438 / 1643 / 1837 / 640 / 838 / 1041 / 1242 / 1441 / 1646 / 1842 / 643 / 842 / 1044 / 1245 / 1444 / 1645 / 646 / 845 / 1047 / 1249 / 1447 / 1648 / 649 / 848 / 1051 / 1251 / 652 / 851 / 1054 / 6
Danbury WinairSheet Metal Fabrication(203)885-0627558 Federal Rd, Brookfield, CT 06804Place order at sheetmetal@mywinair.comAll Spiral Estimation is based on:4” Ø to 18” ØGasketed20” Ø and AboveAccuflangeGauge:4” Ø to 10” Ø26g12” Ø to 18” Ø24g20” Ø to 30” Ø22g
K-FLEX NBR/PVC Elastomeric Foam29-Jan-15Page 1 of 4SDS01-0115SAFETY DATA SHEETSECTION 1 - IDENTIFICATIONManufacturer’s name and address:Supplier’s name and address:Refer to ManufacturerK-FLEX USA100 Nomaco DrYoungsville, NC 27596USATelephone No.Website AddressProduct IdentifierChemical NameRecommended Use: (800) 765-6475: www.kflexusa.com: K-FLEX Elastomeric Foam; K-FLEX INSUL-TUBE, K-FLEX INSULSHEET, K-FLEX INSUL-LOCK, K-FLEX INSUL-LOCK SEAM SEAL KFLEX ECO, K-FLEX DUCT LINER GRAY, K-FIT, K-TEK K 41-E,ELASTOMERIC TAPE: NBR/PVC Elastomeric Foam: This product is classified as an “article” according to Title 29 ofthe Code of Federal Regulations, OSHA Part 1910.1200C.SECTION 2 – HAZARD(S) IDENTIFICATIONHazardous Ingredient: NoneSECTION 3 – COMPOSITION/INFORMATION OF INGREDIENTSDescription: Elastomeric closed-cell foam comprised of nitrile butadienerubber/polyvinyl chloride (NBR/PVC). Available in rolls andsheets of various dimensions.SECTION 4 – FIRST-AID MEASURESInhalationSkin ContactEye ContactIngestion: Unlikely route of exposure. No measures established.: If rash or irritation develops, wash with soap and water. If rashor irritation persists, consult a physician.: Small particles may cause irritation. Flush with water. Ifirritation persists, consult a physician.: Unlikely route of exposure. No adverse effects anticipated.100 Nomaco DriveYoungsville, NC 27596800-765-6475Fax: 800-765-6471www.kflexusa.com
K-FLEX NBR/PVC Elastomeric Foam29-Jan-15Page 2 of 4SDS01-0115SECTION 5 – FIRE-FIGHTING MEASURESExtinguishing MediaSpecial Firefighting ProceduresDecomposition Products: Water, CO2, Dry Chemical, Foam: Recommend NIOSH/MSHA approved self-contained breathingapparatus and full protective clothing be worn.: Upon combustion, HCI, HCN, and other hazardous gases maybe evolved.SECTION 6 – ACCIDENTAL RELEASE MEASURESPersonal Precautions: Recommend light to medium duty cloth or leather gloves andapproved safety glasses.: None.Emergency ProceduresSECTION 7 – HANDLING AND STORAGEHints for Safe HandlingHints for Fire and Explosion ProtectionHints for Separation of IncompatibleMaterialsStorage Recommendations: None.: None.: None.: Avoid storage in confined areas where temperatures mayexceed 51 C (125 F).SECTION 8 – EXPOSURE CONTROLS/PERSONAL PROTECTIONMedical Conditions Aggravated byExposureCodes UsedGeneral Health MeasuresEngineering Controls::::Not established.N/AN/ALocal exhaust ventilation is recommended for control ofairborne dust, fumes, and vapors in confined areas.SECTION 9 – PHYSICAL AND CHEMICAL PROPERTIESAppearanceColorOdorMelting PointBoiling PointLower Explosion LimitUpper Explosion LimitVapor Pressure @ 20 C::::::::Sheets, rolls, and tubes; some with self-adhesiveBlack, white, or gray.Negligible to no odor.N/AN/AN/AN/A0.1100 Nomaco DriveYoungsville, NC 27596800-765-6475Fax: 800-765-6471www.kflexusa.com
K-FLEX NBR/PVC Elastomeric Foam29-Jan-15Vapor Density (Air 1)SolubilitySpecific Gravity (H2O 1)Flash PointPage 3 of 4SDS01-0115::::N/AInsolubleN/AN/ASECTION 10 – STABILITY AND REACTIVITYStabilityIncompatibilityDecomposition Products: Stable.: N/A: Upon combustion, HCI, HCN, and other hazardous gases maybe evolved.SECTION 11 – TOXICOLOGICAL INFORMATIONEffects on short- and long-termExposure: When used and handled according to specification, theproduct does not have any harmful effect to the best of ourknowledge.SECTION 12 – ECOLOGICAL INFORMATIONClassified as non-hazardous to waters.SECTION 13 – DISPOSAL CONSIDERATIONSDisposal: Not a RCRA hazardous waste. Dispose of in accordance withlocal, state, and federal regulations.SECTION 14 – TRANSPORT INFORMATIONNo hazardous materials.SECTION 15 – REGULATORY INFORMATIONN/A100 Nomaco DriveYoungsville, NC 27596800-765-6475Fax: 800-765-6471www.kflexusa.com
K-FLEX NBR/PVC Elastomeric Foam29-Jan-15Page 4 of 4SDS01-0115SECTION 16 – OTHER INFORMATIONRevised January, 2015. The information and recommendations contained herein are based upon datathat is accurate and reliable, to the best of K-FLEX USA, LLC knowledge and belief. With respect toinformation and recommendations, K-FLEX USA, LLC makes no representations or warranties of any kindor nature, expressed or implied.100 Nomaco DriveYoungsville, NC 27596800-765-6475Fax: 800-765-6471www.kflexusa.com
S A F E T YD A T AS H E E TPage 1Water Based Liner AdhesiveSECTION I - PRODUCT AND COMPANY IDENTIFICATIONPRODUCT NAME:MANUFACTURERS’ADDRESS:EMERGENCY PHONE:BUSINESS HOURS:REVISION DATE:INFORMATION PHONE:REVISION #:PREPARED BY:DOT HAZARD CLASS:Water Based Liner AdhesiveElgen Manufacturing Company INC.10 Railroad Ave, Closter NJ 07624INFOTRAC: (800) 535-50536AM - 6PM04/01/2016(800)503-98053-15IT Department. Supersedes all previousNot Hazardous - UN Number: N/ASECTION II - HAZARDOUS INGREDIENTS / SARA III INFORMATIONHMIS Ratings: Health: 1 Flammability: 0 Reactivity: 0 Personal Protective Equipment: BREPORTABLE COMPONENTSWeight %CAS NUMBERNoneSECTION III – COMPOSITION/INFORMATION ON INGREDIENTSPROPRIETARY COMPONENTCAS NUMBERTrade SecretProprietary BlendCONCENTRATIONSECTION IV – FIRST AID MEASURESINHALATION:Remove to fresh air. If breathing is difficult, administer oxygen. If breathing has stopped, administerartificial respiration. Contact physician or emergency medical facility immediately.SKIN:Remove contaminated clothing and shoes. Wash exposed area thoroughly with soap and water for atleast 15 minutes. Do not rub affected area. If irritation persists, get medical attention. Skin reactionmay take 24 to 48 hours to develop. Wash contaminated clothing before reuse.Immediately flush eyes with large amounts of water for at least 15 minutes while frequently lifting theupper and lower eyelids. If irritation persists, call a physician.EYES:INGESTION:Do not induce vomiting. Contact physician or emergency medical facility immediately. Never giveanything by mouth to an unconscious person.SECTION V - FIRE-FIGHTING MEASURESFLASH POINTNoneFIRE AND EXPLOSION HAZARDClosed containers exposed to extreme heat may rupture due to pressure build upEXTINGUISHING MEDIAThe product will only burn after the water it contains is driven off. Fordried film use water, foam, carbon dioxide or dry chemical.FIRE FIGHTING INSTRUCTIONSWater may be used to cool exposed containers.SECTION VI – ACCIDENTAL RELEASE MEASURESSPILL CLEANUP:Dike, contain, or absorb with inert absorbent material. Collect spilled material in a salvage container.Prevent spill from entering sewers, drains, streams, waterways, or other bodies of water.ACCIDENTAL RELEASE MEASURES:Dispose of in accordance with all local, state and federal regulations.SECTION VII – HANDLING AND STORAGEHANDLING:DO NOT ALLOW TO FREEZE. Store in a cool dry location away from heat. Keep containers tightly closedand store with adequate ventilation.OTHER PRECAUTIONS: DO NOT TAKE INTERNALLY. Avoid inhalation of excess vapors, ingestion, and unnecessary, prolonged, or repeated contact with this and any other chemical. Change soiled work clothes frequently. Clean hands after handling. KEEP OUT OF REACH OF CHILDREN.STORAGE:Keep in a dry, cool place, protect material from freezing.
S A F E T YD A T AS H E E TWater Based Liner AdhesivePage 2SECTION VIII – EXPOSURE CONTROLS/PERSONAL PROTECTIONENGINEERING CONTROLS :Use only in area provided with appropriate exhaust ventilation.EYE PROTECTION :Use chemical splash goggles or OSHA permitted safety glasses.SKIN PROTECTION :Protection glovesRESPIRATORY PROTECTION :Not required under normal conditions. Provide sufficient ventilation to maintain constantfresh air in workspace. If TLV is exceeded, use NIOSH/MSHA approved organic vaporand mist, supplied air, or self-contained breathing apparatus. Avoid breathing sandingdust.SECTION IX - PHYSICAL / CHEMICAL PROPERTIESFORMMobile LiquidSPECIFIC GRAVITY(H20 1) 1.1-1.2COLORWhite or BlackBOILING POINT212 FODORMild, SweetPH8.0-9.5SOLUBILITY IN WATERMisciblePERCENT VOLATILE BY WEIGHT55-65%COATING V.O.C.22 g/lVISCOSITY (CPS)approx. 2,000-3,500WATER SOLUBILITYSolubleFREEZING POINT32 F(0 C)SECTION X – STABILITY AND REACTIVITY DATACONDITIONS TO AVOID :Coagulation may occur after freezing, thawing, or boiling.INCOMPATIBILITY :Metal salts, mineral acids (i.e. sulfuric, phosphoric, etc.) Strong oxidizing agents. Strongreducing agents.DECOMPOSITION :POLYMERIZATION :May form toxic materials on thermal decomposition including Carbon monoxide (CO),Carbon dioxide (CO2), and various hydrocarbons. Under fire conditions, this product willrelease hydrogen chloride gas.Polymerization will not occur.STABILITY :Stable at ambient temperatures.SECTION XI – TOXICOLOGICAL INFORMATIONSKIN :Prolonged and repeated contact with product may cause skin irritation.EYES :Direct contact, may cause irritation.INHALATION :Adverse health effects from vapors or spray mists in poorly ventilated areas may includeirritation of the mucous membranes of the nose, throat, and respiratory tract and symptoms of headache and nausea.SECTION XII – ECOLOGICAL INFORMATIONECOTOXICITY:No ecotoxicity data was found for the productENVIRONMENTAL FATE:No environmental information found for this productSECTION XIII – DISPOSAL CONSIDERATIONSConsult with the US EPA Guidelines listed in 40 CFR Part 261.3 for the classifications of hazardous waste prior to disposal. Furthermore, consult with your state and local waste requirements or guidelines, if applicable, to ensure compliance. Arrange disposal inaccordance to the EPA and/or state and local guidelines.
S A F E T YD A T AS H E E TWater Based Liner AdhesivePage 3SECTION XIV – TRANSPORT INFORMATIONDOT HAZARD CLASSNot HazardousUN NUMBERN/APACKING GROUPN/ASHIPPING NAMEN/ASECTION XV –REGULATORY INFORMATIONThis product is considered non-hazardous under the OSHA Hazard Communication Standard 29 CFR 1910.1200.EMERGENCY PLANNING AND COMMUNITY RIGHT-TO-KNOW (SARA TITLE III):Section 311/312 Categorizations (40 CFR 370): Immediate (Acute) Health Hazard.Section 313 Information (40 CFR 372) – Toxic Chemicals List: This product contains the following substances subject to the reportingrequirements of Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 and 40 CFR 372:Component:none. Toxic Substances Control Act (TSCA): All components of this product are on the TSCA Inventory or are exempt from TSCAInventory requirements.CALIFORNIA PROPOSITION 65 (Safe Drinking Water and Toxic Enforcement Act of 1986): None listed.SECTION XVI –OTHER INFORMATIONCREATION DATE06/10/2009REVISION DATE06/01/2016REVISION NOTESDS - 16 SectionAUTHORIT DepartmentAll the information above is believed to be accurate and represents the best information currently available to us. However, we make no warranty ofmerchantability or any other warranty, express or implied, with respect to such information, and we assume no
558 Federal Road, Brookfield, CT 06804 O. (203) 885-0627 F. (203) 740-2441 sheetmetal@mywinair.com www.mywinair.com. 5ft Coil/Sheet Stock/ (TDC/TDF) Duct Reinforcement ¾ Tie-Rods USA Steel G90.
