WIXLIB

162970 SHEET 01 OF 09GENERAL NOTESTHESE INSTALLATION INSTRUCTIONS ARE A SUPPLEMENT TOTHE APPROVED SHOP DRAWINGS. USE IN CONJUNCTION WITHTHOSE DRAWINGS.HANDLING, STORING AND PROTECTINGALUMINUM MATERIALG)H)CHECK ALL MATERIAL ON ARRIVAL FOR QUANTITY.K)BE SURE TO HAVE ALL THE MATERIALS AND TOOLSNEEDED TO BEGIN THE INSTALLATION.1.2.3.4.APPROVED SHOP DRAWINGS.LEVEL AND PLUMB (TRANSIT).FASTENERS AND REQUIRED DRIVERS.PERIMETERS AND ACCESSORIES SUCH AS ANCHORS,FASTENERS, SLEEVES AND/OR SPLICE CAPS.5. SEALING MATERIALS.6. GLAZING MATERIALS.HANDLE CAREFULLY - DO NOT DROP FROM THE TRUCK.STACK WITH ADEQUATE SEPARATION SO MATERIAL WILLNOT RUB TOGETHER. STORE OFF THE GROUND.PROTECT AGAINST ELEMENTS AND OTHERCONSTRUCTION TRADES.L)B)KEEP MATERIAL AWAY FROM WATER, MUD AND SPRAY PREVENT CEMENT, PLASTER AND OTHER MATERIALSFROM DAMAGING THE FINISH.C)PROTECT THE MATERIALS AFTER ERECTION, BYWRAPPING WITH KRAFT PAPER - OR BY ERECTINGVISQUEEN/CANVAS SPLATTER SCREENS. CEMENT,PLASTER, TERRAZZO AND OTHER ALKALINE MATERIALSARE VERY HARMFUL TO THE FINISH AND SHOULD BEREMOVED WITH WATER AND MILD SOAP BEFORESETTING OCCURS. UNDER NO CIRCUMSTANCES ALLOWTHESE MATERIALS TO TO DRY OR PERMANENT STAININGWILL OCCUR.GENERAL RULESTHE FOLLOWING PRACTICES ARE RECOMMENDED FOR ALLWALL INSTALLATIONS.A)READ COMPLETE INSTRUCTIONS BEFORE ORDERINGGLASS OR FABRICATING MATERIAL.B)CHECK SHOP DRAWINGS TO BECOME THOROUGHLYFAMILIAR WITH THE JOB.C)ALL MATERIALS ARE TO BE INSTALLED PLUMB, LEVELAND TRUE.D)ALL WORK SHOULD START FROM ESTABLISHED BENCHMARKS AND COLUMN CENTER LINES ESTABLISHED BYTHE ARCHITECTURAL DRAWINGS AND THE GENERALCONTRACTOR.E)F)THE SEQUENCE OF ERECTION SHOULD BECOORDINATED WITH THE JOB SUPERINTENDENT SODELAYS ARE PREVENTED AND RISK OF MATERIALDAMAGE IS MINIMIZED. IF PRESETTING OF ANCHORAGEIS REQUIRED, COORDINATE WITH GENERALCONTRACTOR AND SUPERVISE LOCATION.MAKE CERTAIN CONSTRUCTION WHICH WILL RECEIVEYOUR MATERIALS IS ACCORDING TO THE CONTRACTDOCUMENTS. IF NOT, NOTIFY THE GENERALCONTRACTOR IN WRITING AND RESOLVE DIFFERENCESBEFORE PROCEEDING WITH YOUR WORK.FOLLOW KAWNEER INSTALLATION AND GLAZINGINSTRUCTIONS.J)THE FOLLOWING PRECAUTIONS ARE RECOMMENDED TOASSURE EARLY ACCEPTANCE OF YOUR PRODUCTS ANDWORKMANSHIP.A)INSULATE ALL ALUMINUM TO BE PLACED DIRECTLY INCONTACT WITH THE MASONRY OR INCOMPATIBLEMATERIALS WITH A HEAVY COAT OF ZINC CHROMATE ORBITUMINOUS PAINT.FOLLOW SEALANT MANUFACTURER'SRECOMMENDATIONS FOR PROPER SEALANT ANDAPPLICATION. ALL SEALANTS AND MASTICS MUST BECOMPATIBLE WITH ALL SURFACES INCLUDING OTHERSEALANT SURFACES. WHERE REQUIRED ALL SEALANTSMUST ADHERE TO ALL SURFACES INCLUDING OTHERSEALANT SURFACES.REFERENCEINSTRUCTIONS162983 FOREXTERIOR FRAMEPERIMETERSOPENSIDEUPCONFIDENTIAL AND PROPRIETARY INFORMATIONKAWNEER COMPANY INC.THESE DRAWINGS ARE THE SOLE AND EXCLUSIVE PROPERTY OF KAWNEER AND CONTAINSENSITIVE, PRIVILEGED OR CONFIDENTIAL INFORMATION WHICH MAY BE USED ONLY FOR ITSBENEFIT. THE DISCLOSURE OF THESE DRAWINGS TO UNAUTHORIZED PERSONS IS STRICTLYPROHIBITED. THIS DOCUMENT AND ALL COPIES MUST BE RETURNED UPON DEMAND.COPYRIGHT KAWNEER COMPANY, INC., 2013HEAD OPENSIDEDOWNSTOOLINTERMEDIATEHORIZONTALSSILL CONDITIONOPENSIDEDOWNSHEARBLOCKSECTION A-AASILL HORIZONTALSMUST BE SHIMMEDTHE OPEN SIDE OF THE OPEN BACK HORIZONTAL IS TO BEPOSITIONED AS SHOWN BELOW. THE INTERMEDIATEHORIZONTAL IS POSITIONED OPEN SIDE DOWN FOR DEAD LOADSUPPORT.WHICH ACCEPT BOTH 1" AND 1/4" INFILLS. ALSO 1/4" FRAMINGMEMBERS WHICH ACCEPT 1/4" INFILLS ONLY ARE AVAILABLE.GLASS BITE IS 1/2" AT VERTICALS AND HORIZONTALS. GLASSSIZES MUST BE CALCULATED FROM APPROVED SHOPDRAWINGS.WHEN THE OPEN SIDE OF THE OPEN BACK HORIZONTAL ISEXPOSED AND AT EYE LEVEL A SNAP-IN FILLER IS AVAILABLE.OPENSIDEUPUNLESS OTHERWISE SPECIFIED, IT IS RECOMMENDED THATSILICONE SEALANT BE USED FOR ALL INTERNAL SEALS.SEALANT MUST BE APPLIED PER THE SEALANTMANUFACTURER'S RECOMMENDATIONS AND PASS ALLADHESION AND COMPATIBILITY TESTING. AT ALL JOINT SEALS,SEALANT MUST ADHERE TO METAL, GASKETS, THERMALSEPARATOR AND JOINT PLUG MATERIALS. CLEAN ALLSURFACES PRIOR TO APPLICATION OF SEALANT AND PRIMEWHERE NECESSARY TO ACHIEVE PROPER ADHESION.SHIM ALL SILL HORIZONTALS AT SETTING BLOCK LOCATIONS.WHEN THE SNAP-IN FILLER IS NOT USED, AND DUE TOSTANDARD COMMERCIAL EXTRUDING TOLERANCES, IT MAYBE REQUIRED TO USE A 4" PIECE OF THE FILLER AT EACH ENDOF A HORIZONTAL.USE PART 162316 FOR THE 6" DEEP SYSTEMUSE PART 162317 FOR THE 7 1/2" DEEP SYSTEMHEAD CONDITIONOPENSIDEDOWNALL INTERMEDIATEHORIZONTALSOPENSIDEDOWNSILL CONDITIONOPEN BACK HORIZONTAL NOTESTHE OPEN BACK HORIZONTAL IS TO BE TYPICALLY USED FORALL HEAD/SILL AND LAST BAY INTERMEDIATE HORIZONTALS.THE OPEN BACK HORIZONTAL CAN BE USED AT OTHERCONDITIONS IF IT IS AN ADVANTAGE TO THE JOB DESIGN.THE SHEAR BLOCK AT ALL OPEN BACK INTERMEDIATEHORIZONTALS HAS THE OPTION TO BE PRE-INSTALLED INTOTHE HORIZONTAL BEFORE HORIZONTALS ARE INSTALLEDOPEN BACK HORIZONTALSWHENEVER POSSIBLE AVOID USING OPEN BACK HORIZONTALSHORIZONTAL BECOMES ABSOLUTELY NECESSARY THE SHEARBLOCK CONNECTION WILL BE AS SHOWN BELOW.ALSO REFER TO CORNER INSTRUCTIONS 162972CURTAIN WALLINSTALLATIONProduct Engineering & Development INSTRUCTIONS95449-11504/21/17162970 SHEET 01 OF 09

162970 SHEET 02 OF 09STEP 1 - CHECK OPENINGSSTEP 4 - FRAME ASSEMBLYSTEP 4 - FRAME ASSEMBLYELEVATIONS AND SLABS MUST BE WITHIN ADJUSTMENT OFANCHORING SYSTEM. SEE APPROVED SHOP DRAWINGS FORALLOWABLE ADJUSTMENT.ATTACH ANCHORS TO MULLIONS WHERE APPLICABLE.ATTACH SHEAR BLOCKSANCHORING SURFACES OF PERIMETER CONSTRUCTIONMUST BE LEVEL AND PLUMB WITHIN THE ADJUSTMENTLIMITS OF THE HEAD, SILL AND JAMB. SEE APPROVED SHOPDRAWINGS FOR ALLOWABLE ADJUSTMENT.STEP 2 - LAY OUT ANCHOR ANDMULLION CENTERLINESANCHOR PREP MAY BE FABRICATED IN THE FIELDOR FACTORY. CONSULT APPROVED SHOPDRAWINGS FOR CORRECT METHOD.027477SEPARATORBETWEEN ANCHORAND MULLIONHEAD/SILL SHEAR BLOCK/ANCHORWHERE APPLICABLE AND SHOWN BELOW.THERMAL BREAKTO BE SAMELENGTH ASVERTICALMULLIONS162314 (6" SYSTEM AT JAMBS)162315 (7-1/2" SYSTEM AT JAMBS)162342 (6" SYSTEM AT MULLIONS)162343 (7-1/2" SYSTEM AT MULLIONS)WELD PLATESIZE AND SPACING OFWELD PER APPROVEDSHOP DRAWINGSVARIES WITHJOB CONDITIONSOPTION TOINSTALL THERMALBREAK AFTERVERTICALS ANDHORIZONTALSARE INSTALLEDWHEN WELDING ANCHORS, PROTECT INSTALLED GLASSAND METAL FROM WELD SPLATTER.USE COLUMN CENTER LINES ESTABLISHED BY THEGENERAL CONTRACTOR. ON EACH FLOOR LAY OUT MULLIONCENTER LINES AND ANCHOR CENTER LINES.EXTERIORFACE OFBEAM ORFLOOR SLAB162310THERMAL BREAK128394 SCREWS#12 x 1-7/8"PAN HEADTYPE BSTANDARD ANCHOR PREP IS THRU-BOLTED ATINTERMEDIATE VERTICALS AND TAPPING PLATES ARE USEDAT JAMB VERTICALS. REFER TO APPROVED SHOPDRAWINGS FOR CORRECT METHOD.USE WALL LINES ESTABLISHED BY THE GENERALCONTRACTOR. ON EACH FLOOR LAY OUT A REFERENCE LINETO ESTABLISH IN AND OUT WALL LOCATIONS.C/L OF MULLIONSTEP 5 - INSTALL THERMAL BREAKSTRUCTURAL INTEGRITY OFANCHOR AND FASTENERS MUST BECHECKED BY FACTORY ENGINEERS.ANCHOR FASTENERLOCATIONS PERAPPROVED SHOPDRAWINGSDO NOT OVER TIGHTEN ANCHOR CONNECTIONS.TIGHTEN TO A "SNUG TIGHT" POSITION WITHPARTS BROUGHT INTO GOOD CONTACT. BESURE ANY SPRING TYPE LOCK WASHERS ARECOMPRESSED. THEN TIGHTEN APPROXIMATELY1/2 MORE TURN.THERMAL BREAKTO BE 1/4"SHORT AT EACHEND OFHORIZONTALS1/4"INSTALL HEAD AND SILL END CAPS162388 (1" FRAMING)162389 (1/4" FRAMING)SET IN SEALANTSHEAR BLOCK/ANCHOR128396 SCREWS#12 x 7/16"PAN HEAD TYPE BATTACH SHEAR BLOCKS.TYPICALMULLIONTYPICAL INTERMEDIATE SHEAR BLOCKS162377 (6" SYSTEM)162378 (7-1/2" SYSTEM)STEP 5 - INSTALL THERMAL BREAKSEE APPROVED SHOPDRAWINGS FORANCHOR LAYOUTSHEAD AND SILL SHEAR BLOCKS162331 (6" SYSTEM)162332 (7-1/2" SYSTEM)STEP 3 - INSTALL PRESET ANCHORS IFAPPLICABLEUSING LOCATION LINES PREVIOUSLY ESTABLISHED INSTALLPRESET ANCHORS IN PLACE PER APPROVED SHOPDRAWINGS.REFERENCE INSTRUCTIONS 162983FOR EXTERIOR FRAME PERIMETERSHEAD AND SILL SHEAR BLOCKS162384 (6" SYSTEM)162385 (7-1/2" SYSTEM)162310NOT REQUIRED AT EXTERIORFRAME PERIMETERS SHOWN ININSTRUCTIONS 162983 AND ATOPTIONAL PERIMETER FILLERS 162022AND 162023DO NOT STRETCHWHEN REMOVINGFROM COIL ANDCARTONDO NOTSTRETCHDURINGINSTALLATIONCURTAIN WALLINSTALLATIONProduct Engineering & Development INSTRUCTIONS162310THERMAL BREAK95449-11504/21/17162970 SHEET 02 OF 09

162970 SHEET 03 OF 09STEP 6 - PERIMETERS WHEREAPPLICABLESTEP 7 - INSTALL VERTICAL MULLIONS"F" OR "T" ANCHORSWHERE APPLICABLEINSTALL PERIMETER MEMBERS PER APPROVEDSHOP DRAWINGS. PERIMETER MEMBERS CANOCCUR AT HEAD, SILL OR JAMB CONDITIONS.BENCHMARK TO FACE OFPERIMETER MEMBERPER APPROVED SHOPDRAWINGS"F" AND "T"ANCHOR FASTENERLOCATIONS PERAPPROVED SHOPDRAWINGSSTEP 7 - INSTALL VERTICAL MULLIONSHEAD/SILL SHEAR BLOCK/ANCHORWHERE APPLICABLE.VERTICAL SPLICEJOINTS WHEREAPPLICABLE.CAN NOT BE USED WITH EXTERIOR FRAMEPERIMETERS SHOWN ON INSTRUCTIONS 162983162314 (6" SYSTEM AT JAMBS)162315 (7-1/2" SYSTEM AT JAMBS)162342 (6" SYSTEM AT MULLIONS)162343 (7-1/2" SYSTEM AT MULLIONS)REFERENCEINSTRUCTIONS162983 FOREXTERIOR FRAMEPERIMETERSCONTINUOUS "F" PERIMETER162017 (1" GLASS)162176 (1/4" GLASS)STEP 7 - INSTALL VERTICAL MULLIONSSLEEVE IS FACTORYTAPED INTO THEBOTTOM OF THETOP VERTICAL128284 SCREWS#12 x 1-1/2FLAT HEADTYPE ABTHESE SHEARBLOCKS MAY NEEDTO BE REMOVED TOINSTALL A ANCHORFASTENER THATMIGHT BE LOCATEDCLOSE TO THEMULLIONREMOVE THE TAPEAND LET THE SLEEVESLIDE DOWN TO THEFACTORY APPLIEDSTOP SCREW128284 SCREWS#12 x 1-1/2FLAT HEADTYPE ABFOR HORIZONTALATTACHMENTFIELD APPLIEDFIXING SCREW128348#10 x 1-1/4"FLAT HEADSELF DRILLINGTHE ABOVE SCREWS ARE ONLY USED AT THEOPTIONAL SHEAR BLOCK/ANCHORS.STRUCTURAL SHIMMING IS REQUIRED ATSILL TO ACCOMPLISH DESIGNEDPERIMETER SEAL WIDTHUSE GLAZING 162350 TEMPORARIESWITH 128406 SCREWSANCHOR FASTENERLOCATIONS PERAPPROVED SHOPDRAWINGSMAXIMUM TEMPORARY SPACING IS 30".IF MORE THAN A 50 MPH WIND ISEXPECTED INSTALL PRESSURE PLATES.STEP 7 - INSTALL VERTICAL MULLIONSDIMENSION BUILD-UP CHECK CHECKOVERALL FRAME DIMENSIONS ABOUT EVERYFIVE MULLIONS ON LONG RUNS. THIS IS TOAVOID DIMENSION BUILD-UP10 UNITS CHECK DIMENSIONSHOP APPLIEDSTOP SCREW128267#12 x 1" PAN HEADTYPE ABUSE TEMPORARYSPACERS FORJOINT DIMENSION"F" AND "T" ANCHORFASTENER LOCATIONSPER APPROVEDSHOP DRAWINGSAT MULLION JAMBSIDE, APPLY (2) 128396SCREWS AS SHOWNTO CENTER F-CLIPS ASREQUIRED.SPLICE JOINTWHEN IT OCCURSAT A HORIZONTAL1 1/4"1/8"5 UNITS CHECK DIM.SILL SHOWNHEAD SIMILARANCHOR FASTENERLOCATIONS PERAPPROVED SHOPDRAWINGSCURTAIN WALLINSTALLATIONProduct Engineering & Development INSTRUCTIONS95449-11504/21/17162970 SHEET 03 OF 09

162970 SHEET 04 OF 09STEP 8 - INSTALL HEAD/SILL ANDINTERMEDIATE HORIZONTALSTUBULAR HORIZONTALS128405 SCREWS#12 X 7/8"FLAT HEADTYPE ABSTEP 8 - INSTALL HEAD/SILL AND INTERMEDIATE HORIZONTALSREFERENCE INSTRUCTIONS 162983 FOREXTERIOR FRAME PERIMETERSINSTALLING CEILING INTERMEDIATEOPEN BACK HORIZONTALAAOPEN BACK HORIZONTALS AND LAST BAY HORIZONTALS.FILLER AVAILABLE WHEN OPEN BACK IS EXPOSED AND ATEYE LEVEL.128405 SCREWS#12 X 7/8"FLAT HEAD TYPE ABINSTALLING STOOL INTERMEDIATEOPEN BACK HORIZONTALHEADJOINT PLUG162321 (1" FRAMING)162322 (1/4" FRAME MEMBERS)STEP 9 - INSTALL JOINT PLUGSCEILINGALL SURFACES AND GROOVES MUST BECLEANED PER THE SEALANT MANUFACTURER'SRECOMMENDATIONS.JUST BEFORE INSTALLING JOINT PLUGSAPPLY SEALANT AS SHOWN FILLINGGASKET POCKET AND ADAPTER GROOVE.SECTION A-ASTOOLTHERMAL BREAKTO BE 1/4"SHORT AT EACHEND OF1/4HORIZONTALS"APPLY SEALANT TO THISFACE OF JOINT PLUGFILLGASKETPOCKETFILLADAPTERGROOVESEAL AROUND JOINT PLUGEDGES AND COMPLETELYOVER JOINT PLUG WITHSEALANT AND TOOLAS SHOWNSEAL AROUND JOINT PLUGEDGES AND COMPLETELYOVER JOINT PLUG WITHSEALANT AND TOOLAS SHOWNSILLREFERENCE INSTRUCTIONS 162983 FOREXTERIOR FRAME PERIMETERSFACE VIEWCURTAIN WALLINSTALLATIONProduct Engineering & Development INSTRUCTIONS95449-11504/21/17162970 SHEET 04 OF 09