Transcription
This is a preview of "ANSI/NACE Standard M.". Click here to purchase the full version from the ANSI store.Item No. 21305International StandardANSI/NACE MR0103/ISO17945:2015Petroleum, petrochemical and naturalgas industries — Metallic materialsresistant to sulfide stress cracking incorrosive petroleum refiningenvironmentsÉlément introductif — Élément central — ÉlémentcomplémentaireAn American National StandardApproved November 23, 2015Reference numberANSI/NACE MR0103/ISO 17945:2015 ANSI/NACE/ISO 2015
This is a preview of "ANSI/NACE Standard M.". Click here to purchase the full version from the ANSI store.
This is a preview of "ANSI/NACE Standard M.". Click here to purchase the full version from the ANSI store.COPYRIGHT PROTECTED DOCUMENTThese materials are subject to copyright claims of ISO and NACE. No part of this publication may be reproduced in anyform, including an electronic retrieval system, without the prior written permission of NACE. All requests pertaining to theANSI/NACE MR0103/ISO 17945 standard should be submitted to NACE. All rights reserved.International Organization for Standardization (ISO)ISO Central SecretariatBIBC IIChemin de Blandonnet 8CP 4011214 Vernier, GenevaSwitzerlandTel. 41 22 749 01 11Fax 41 22 749 09 47Web: www.iso.chNACE International15835 Park Ten PlaceHouston, TX 77084-5145Tel. 1 281-228-6223Fax 1 281-228-6300Web: www.nace.orgPrinted in the U.S.A. by NACE International NACE/ISO 20151
This is a preview of "ANSI/NACE Standard M.". Click here to purchase the full version from the ANSI store.Contents . PageForeword . 5Introduction . 61Scope . 72Normative references . 73Terms and definitions . 74Symbols and abbreviated terms . 955.15.2Responsibilities . 9Responsibilities of the end user. 9Responsibility of the manufacturer. 1066.16.26.36.46.56.6Factors contributing to SSC. 10General parameters affecting SSC . 10Effect of material condition and stress level on susceptibility to SSC . 10Effect of hydrogen permeation flux on SSC . 11Effect of elevated temperature exposure on SSC . 12Factors affecting time to failure due to SSC . 12Bases for establishing whether equipment falls within the scope of this InternationalStandard . 127Materials included in this International Standard . 128Hardness requirements . 1399.19.29.3Procedure for the addition of new materials or processes. 14General balloting requirements . 14Field experience data requirements . 14Laboratory test data requirements . 1410New restrictions and deleted materials. 1411Qualification of unlisted alloys, conditions, and/or processes for specificapplications . 1512Standard road map . 151313.113.1.113.1.2Ferrous materials. 17Carbon and alloy steels . 17Requirements for all carbon and alloy steels . 17Requirements for carbon steels listed as P-No. 1 Group 1 or 2 in Section IX of theASME BPVC. 1713.1.3 Requirements for other carbon steels. 1813.1.4 Requirements for alloy steels listed with P-numbers in Section IX of the ASME BPVC . 182 NACE/ISO 2015
13.1.5 Requirements for other alloy steels . 1813.1.6 Requirements for cold-formed carbon and alloy steels . 18This is 13.1.7a previewof "ANSI/NACEStandardM.".steelsClicklistedhere tofull versionthe ANSI store.Weldingrequirementsfor carbonas purchaseP-No. 1 in theSectionIX of thefromASMEBPVC . 1913.1.8 Welding requirements for alloy steels listed as P-No. 3, 4, or 5A in Section IX of theASME BPVC . 1913.1.9 Corrosion resistant weld overlays, hard facing weld overlays, cladding, and thermalspray coatings on carbon steels and alloy steels. 1913.2 Cast iron and ductile iron . 2013.3 Ferritic stainless steels . 2013.4 Martensitic stainless steels . 2013.4.1 Conventional martensitic stainless steels . 2013.4.2 Low-carbon martensitic stainless steels . 2013.4.3 Welding and overlays on martensitic stainless steels . 2113.5 Austenitic stainless steels. 2113.6 Specific austenitic stainless steel grades . 2213.7 Highly alloyed austenitic stainless steels . 2213.8 Duplex stainless steels . 2313.8.1 General requirements for duplex stainless steels . 2313.8.2 Welding requirements for duplex stainless steels . 2313.9 Precipitation-hardenable stainless steels . 2313.9.1 Austenitic precipitation-hardenable stainless steel . 2313.9.2 Martensitic precipitation-hardenable stainless steels . 2313.9.3 Welding requirements for precipitation-hardenable stainless steels . 241414.114.1.114.1.214.214.314.414.514.6Nonferrous materials . 25Nickel alloys . 25Solid-solution nickel alloys . 25Precipitation-hardenable nickel alloys . 26Cobalt-Nickel-chromium-molybdenum alloys . 26Cobalt-nickel-chromium-tungsten alloys . 27Titanium alloys . 27Aluminium alloys . 28Copper alloys . ation requirements . 28General fabrication requirements. 28Corrosion resistant overlays, hard facing overlays, and cladding . 28Welding . 28Cladding on carbon steels, alloy steels, and martensitic stainless steels. 29Identification stamping . 29Threading . 30Machine-cut threads . 30Cold-formed (rolled) threads . 30Cold-deformation processes . 301616.116.216.3Bolting. 30General bolting requirements . 30Exposed bolting . 30Nonexposed bolting . 3117Plating, coatings, and diffusion processes . 311818.118.218.318.4Special components . 31General requirements for special components . 31Bearings .
23.11.2015 · the first edition of NACE MR0103 was published as a refinery-specific sour service metallic materials standard. This International Standard is based on the good experience gained with NACE MR0175/ISO 15156, but tailored to refinery environments and applications. Other references for this International Standard are NACE SP0296, NACE Publication 8X194, NACE Publication 8X294, and
