Transcription
MPI Architectural Painting ManualShort Form Guide SpecificationRevision: June 2004Section 09900PaintingPage 1 of 15PART 1 - GENERALSPEC NOTES:.1Use this guide specification when a “short form” specification is required to specify painting and decorating work on new, previouslyunpainted surfaces.2Refer to the MPI Architectural Manual “long form” painting specification for guidance and spec notes when using this specification.1.1Description:SPEC NOTE:1.2This article (1.1) is not intended to “scope” the work but to serve as a general description. The onus of defining the extent ofthis section of Work remains with the Project General Contractor, who will ensure that the area / scope of responsibility of anyparticular Subcontractor / supplier is set out in full detail when awarding the painting and decorating subcontract. The extent ofthis section of Work is also governed by the limits of local trade agreements and conditions.1Section Includes: All labor, materials, tools and other equipment, services and supervision required to completeall exterior and interior painting and decorating work as indicated on Finish Schedules and to the full extent of thedrawings and specifications.2The Work shall also include, but not necessarily be limited to surface preparation of substrates as required foracceptance of painting, including cleaning, small crack repair, patching, caulking, making good surfaces andareas, pre-treatment, priming and back-priming to the extent / limits defined under MPI preparation requirements.3[Provide Unit, Separate and/or Alternative Prices for items indicated in Section [01215] and/or on Bid Form.]Quality Assurance:.1This Contractor shall have a minimum of five (5) years proven satisfactory experience and shall maintain aqualified crew of painters throughout the duration of the work.2Only qualified journeypersons, as defined by local jurisdiction shall be engaged in painting and decorating work.Apprentices may be employed provided they work under the direct supervision of a qualified journeyperson inaccordance with trade regulations.3All materials, preparation and workmanship shall conform to requirements of the latest edition of the ArchitecturalPainting Specification Manual by the Master Painters Institute (MPI) (hereafter referred to as the MPI PaintingManual) as issued by the local MPI Accredited Quality Assurance Association having jurisdiction.4All paint manufacturers and products used shall be as listed under the Approved Product List section of the MPIPainting Manual.5All painting and decorating work shall be inspected by a Paint Inspection Agency (inspector) acceptable to thespecifying authority and the local MPI Accredited Quality Assurance Association. The painting contractor shallnotify the Paint Inspection Agency a minimum of one week prior to commencement of work and provide a copyof the project painting specification, plans and elevation drawings (including pertinent details) as well as a FinishSchedule.6All surfaces requiring painting shall be inspected by the Paint Inspection Agency who shall notify theConsultant and General Contractor in writing of any defects or problems, prior to commencing painting work, orafter the prime coat shows defects in the substrate.7The painting contractor shall receive written confirmation of the specific surface preparation procedures andprimers used for all fabricated steel items from the fabricator / supplier to ascertain appropriate and manufacturercompatible finish coat materials to be used before painting any such work.The Master Painters Institute1997 - 2004
MPI Architectural Painting ManualShort Form Guide SpecificationRevision: June 20041.3Regulatory Requirements:.11.41.5Section 09900PaintingPage 2 of 15Conform to work place safety regulations and requirements of those authorities having jurisdiction for storage,mixing, application and disposal of all paint and related hazardous materials.Submittals / Mock-Up:.1Submit consent of surety with Bid Submission as proof of ability to supply a 100% two (2) year MaintenanceBond, if an MPI Accredited Quality Assurance Association’s guarantee option is not used.2If requested, submit an invoice list of all painting materials ordered for project work to Paint Inspection Agencyindicating manufacturer, types and quantities for verification and compliance with specification and designrequirements.3Submit two sets of Material Safety Data Sheets (MSDS) prior to commencement of work for review and forposting at job site as required.4At project completion provide an itemized list complete with manufacturer, paint type and color-coding for allcolors used for Owner’s later use in maintenance.5When requested by the Consultant or Paint Inspection Agency, prepare and paint a designated surface, area,room or item (in each color scheme) to requirements specified herein, with specified paint or coating showingselected colors, gloss/sheen, textures and workmanship to MPI Painting Specification Manual standards forreview and approval. When approved, surface, area, room and/or items shall become acceptable standard offinish quality and workmanship for similar on-site work.Product Delivery, Storage, and Handling:.1Deliver and store all painting materials in sealed, original labeled containers bearing manufacturer’s name, brandname, type of paint or coating and color designation, standard compliance, materials content as well as mixingand/or reducing and application requirements in strict accordance with manufacturer and MPI requirements.1.6Environmental, Waste Management and Disposal Requirements:MOVE FROM 1.5.1Perform no painting or decorating work when the ambient air and substrate temperatures, relative humidity anddew point and substrate moisture content is below or above requirements for both interior and exterior work.1.7.2Apply paint only to dry, clean, properly cured and adequately prepared surfaces in areas where dust is no longergenerated by construction activities such that airborne particles will not affect the quality of finished surfaces.3Ensure adequate continuous ventilation and sufficient heating and lighting is in place.4Paint, stain and wood preservative finishes and related materials (thinners, solvents, caulking, empty paint cans,cleaning rags, etc.) shall be regarded as hazardous products. Recycle and dispose of same subject toregulations of applicable authorities having jurisdiction.5To reduce the amount of contaminants entering waterways, sanitary/storm drain systems or into the groundretain cleaning water and filter out and properly dispose of sediments.6Set aside and protect surplus and uncontaminated finish materials not required by the Owner and deliver orarrange collection for verifiable re-use or re-manufacturing.Guarantee:.1Provide and pay for either the local MPI Accredited Quality Assurance Association’s two (2) year guarantee, or,alternatively, a 100% two (2) year Maintenance Bond - both in accordance with MPI Painting Manualrequirements. The Maintenance Bond shall warrant that all painting work has been performed in accordancewith MPI Painting Manual requirements.The Master Painters Institute1997 - 2004
MPI Architectural Painting ManualShort Form Guide SpecificationRevision: June 2004.2Section 09900PaintingPage 3 of 15All surfaces requiring painting shall be inspected by the Paint Inspection Agency who shall notify theConsultant and General Contractor in writing of any defects or problems, prior to commencing painting work, orafter the prime coat shows defects in the substrate.PART 2 - PRODUCTS2.1Materials:SPEC NOTE:2.2.1Only materials (primers, paints, coatings, varnishes, stains, lacquers, fillers, etc.) listed in the latest edition of theMPI Approved Product List (APL) are acceptable for use on this project. All such material shall be from a singlemanufacturer for each system used.2Other materials such as linseed oil, shellac, thinners, solvents, etc. shall be the highest quality product of an MPIlisted manufacturer and shall be compatible with paint materials being used as required.3Where required, use only materials having a minimum MPI “Environmentally Friendly” [E1] [E2] [E3] rating basedon VOC (EPA Method 24) content levels. Where indoor air quality (odour) is an issue, use only MPI listedmaterials having a minimum [E2] [E3] rating.4[Where required to meet LEED (Leadership in Energy and Environmental Design) program requirements, useonly MPI listed materials having an “L” rating designation.]Mixing and Tinting:.12.3Delete, revise or add to the example selections below to suit project requirements.Unless otherwise specified herein or pre-approved, all paint shall be ready-mixed and pre-tinted. Re-mix all paintin containers prior to and during application to ensure break-up of lumps, complete dispersion of settled pigment,and color and gloss uniformity. Where thinner is used, addition shall not exceed paint manufacturer'srecommendations.Finish, Color, Gloss / Sheen:.1Unless otherwise noted, all painting work shall be in accordance with MPI [Custom] [Premium] Grade finishrequirements.2Colors shall be as selected by the Consultant from a manufacturer’s full range of colors. [Refer to FinishSchedule for identification and location of colors] [The schedule will be furnished after award of the Contract,except general requirements shall be as noted herein].SPEC NOTE:Delete, revise or add to the following example selections below to suit project requirements.3Color selection will be based on [five (5)] base colors and [three (3)] accent colors with a maximum of [one (1)]deep or bright color. No more than [eight (8)] colors will be selected for the entire project and no more than[three (3)] colors will be selected in each area. Note that this does not include pre-finished items by others, e.g.flashings, windows, etc.4Gloss level ratings of all painted surfaces shall be as noted on Finish Schedule. Refer to MPI Painting Manual forgloss level definitions and requirements.PART 3 - EXECUTION3.1Condition and Preparation of Surfaces:.1The condition and preparation requirements for all surfaces shall be in accordance with MPI Painting Manualrequirements.The Master Painters Institute1997 - 2004
MPI Architectural Painting ManualShort Form Guide SpecificationRevision: June 20043.2Application:.1Do not paint unless substrates are acceptable and/or until all environmental conditions (heating, ventilation,lighting and completion of other subtrade work) are acceptable for applications of products.2Apply paint or stain in accordance with noted MPI finish Grade requirements.3Painting coats specified are intended to cover surfaces satisfactorily when applied at proper consistency and inaccordance with manufacturer’s recommendations. Apply a minimum of four coats of paint where deep or brightcolors are used to achieve satisfactory results.SPEC NOTE:3.3Section 09900PaintingPage 4 of 15Refer to “long form” specification for spec note information when using the following systems.Exterior Finish / Coating Systems:Paint exterior surfaces in accordance with the following MPI Painting Manual requirements:.1Asphalt Surfaces: (zone / traffic marking for drive and parking areas, etc.)EXT 2.1AEXT 2.1B.2Concrete Vertical Surfaces: (including horizontal soffits)EXT 3.1AEXT 3.1BEXT 3.1CEXT 3.1DEXT 3.1EEXT 3.1FEXT 3.1GEXT 3.1HEXT 3.1JEXT 3.1KEXT 3.1LEXT 3.1MEXT 3.1N.3Latex [insert gloss level] finish.Latex [insert gloss level] finish over latex [insert texture type] aggregate.Waterborne light industrial [insert gloss level] coating.Epoxy finish.Waterborne epoxy finish.Elastomeric coating.Water repellent non-paintable finish.Water repellent paintable finish.Concrete stain finish.Latex [insert gloss level] finish (over alkali resistant primer).High-build latex finish.Pigmented polyurethane finish (over epoxy).Latex [insert gloss level] [insert texture type] aggregate finish.Concrete Horizontal Surfaces: (decks, stairs, driveways, parking and court areas, etc.)EXT 3.2AEXT 3.2BEXT 3.2CEXT 3.2DEXT 3.2EEXT 3.2FEXT 3.2GEXT 3.2HEXT 3.2J.4Latex zone / traffic marking finish.Alkyd zone / traffic marking finish.Latex floor paint [gloss] [low gloss] finish.Latex deck coating.Epoxy non-slip deck coating.Alkyd floor enamel [insert gloss level] finish.Latex zone / traffic marking finish. [for parking lines, etc]Alkyd zone / traffic marking finish. [for parking lines, etc]Clear sealer finish.Clear waterborne sealer finish.Concrete stain finish.Cementitious Composition Board Surfaces: (vertical surfaces, horizontal soffits)EXT 3.3AEXT 3.3BEXT 3.3CEXT 3.3DEXT 3.3ELatex [insert gloss level] finish.Alkyd [insert gloss level] finish.Waterborne light industrial [insert gloss level] coating.Waterborne epoxy finish.Epoxy finish.The Master Painters Institute1997 - 2004
MPI Architectural Painting ManualShort Form Guide SpecificationRevision: June 2004EXT 3.3FEXT 3.3GEXT 3.3HEXT 3.3J.5Latex [insert gloss level] finish.Latex [insert gloss level] [insert texture type] aggregate finish.Waterborne light industrial [insert gloss level] coating. [for moderate chemical resistance]Elastomeric coating.Epoxy finish.Waterborne epoxy finish.Pigmented polyurethane finish (over high build epoxy).Water repellent non-paintable finish. [not for use on light weight block]Water repellent paintable finish. [not for use on light weight block]High-build latex finish.Latex [insert gloss level] finish (over alkali resistant primer).Structural Steel and Metal Fabrications:EXT 5.1AEXT 5.1BEXT 5.1CEXT 5.1DEXT 5.1EEXT 5.1FEXT 5.1GEXT 5.1HEXT 5.1JEXT 5.1KEXT 5.1LEXT 5.1MEXT 5.1NEXT 5.1PEXT 5.1QEXT 5.1REXT 5.1SEXT 5.1T.8Latex [insert gloss level] finish.Latex [insert gloss level] [insert texture type] aggregate finish.Waterborne light industrial [insert gloss level] coating.Epoxy finish. [for smooth brick]Waterborne epoxy finish. [for smooth brick]Water repellent non-paintable finish.Water repellent paintable finish.High-build latex finish.Pigmented polyurethane finish (over epoxy).Concrete Masonry Units: (smooth and split face block and brick).EXT 4.2AEXT 4.2BEXT 4.2CEXT 4.2DEXT 4.2EEXT 4.2FEXT 4.2GEXT 4.2HEXT 4.2JEXT 4.2KEXT 4.2L.7Pigmented polyurethane finish (over epoxy).Latex [insert gloss level] [insert texture type] aggregate finish.High-build latex finish.Latex [insert gloss level] finish (over alkali resistant primer).Clay Masonry Units: (pressed and extruded brick)EXT 4.1AEXT 4.1BEXT 4.1CEXT 4.1DEXT 4.1EEXT 4.1FEXT 4.1GEXT 4.1HEXT 4.1J.6Section 09900PaintingPage 5 of 15Quick dry enamel [insert gloss level] finish.Waterborne light industrial [insert gloss level] coating (over inorganic zinc primer).Waterborne light industrial [insert gloss level] coating (over alkyd primer).Alkyd [insert gloss level] finish (over alkyd primer).Waterborne epoxy finish.Epoxy finish.Pigmented polyurethane finish (over epoxy zinc rich primer and high build epoxy).Pigmented polyurethane finish (over epoxy).Pigmented polyurethane finish (over high build epoxy).Aluminum paint finish.Pigmented polyurethane finish (over inorganic zinc primer and high build epoxy).Waterborne light industrial [insert gloss level] coating (over waterborne primer).Waterborne light industrial [insert gloss level] coating (over epoxy primer).Pigmented polyurethane finish (over epoxy zinc rich primer).Alkyd [insert gloss level] finish (over surface tolerant primer).Waterborne light industrial [insert gloss level] coating (over epoxy).Epoxy (over self-priming epoxy).Pigmented polyurethane finish (over self-priming epoxy).Steel - High Heat: (heat exchangers, breeching, pipes, flues, stacks, etc., with temperature range as noted)EXT 5.2AEXT 5.2BEXT 5.2CEXT 5.2DHeat resistant enamel finish, maximum 400 F (205 C)Heat resistant aluminum enamel finish, maximum 800 F (427 C).Inorganic zinc rich coating, maximum 750 F (400 C).High heat resistant coating, maximum 1100 F (593 C).The Master Painters Institute1997 - 2004
MPI Architectural Painting ManualShort Form Guide SpecificationRevision: June 2004.9Galvanized Metal: (not chromate passivated)For high contact / high traffic areas (doors, frames, railings, misc. steel, pipes, etc.)For low contact / low traffic areas (overhead decking, ducts, gutters, flashing, etc.)EXT 5.3AEXT 5.3BEXT 5.3CEXT 5.3DEXT 5.3EEXT 5.3FEXT 5.3GEXT 5.3HEXT 5.3JEXT 5.3KEXT 5.3L.10Alkyd [insert gloss level] finish (over vinyl wash primer).Pigmented polyurethane finish (over epoxy).Aluminum paint finish.Bituminous finish. [for unexposed copper next to concrete, masonry, etc.]Epoxy finish.Alkyd [insert gloss level] finish (over alkyd primer). [for properly prepared surfaces only]Waterborne light industrial [insert gloss level] coating.Latex [insert gloss level] finish.Stainless Steel: (unpolished)EXT 5.6AEXT 5.6BEXT 5.6CEXT 5.6DEXT 5.6EEXT 5.6FEXT 5.6G.13Alkyd [insert gloss level] finish (over vinyl wash primer and quick dry primer).Pigmented polyurethane finish (over epoxy).Aluminum paint finish.Bituminous finish. [for unexposed aluminum next to concrete, masonry, etc.]Epoxy finish.Alkyd [insert gloss level] finish (over quick dry primer).Waterborne light industrial [insert gloss level] coating.Latex [insert gloss level] finish.Copper: (excluding roofs)EXT 5.5AEXT 5.5BEXT 5.5CEXT 5.5DEXT 5.5EEXT 5.5FEXT 5.5GEXT 5.5H.12Latex [insert gloss level] finish.Alkyd [insert gloss level] finish.Epoxy finish. [for use on high contact / high traffic areas]Pigmented polyurethane finish (over vinyl wash and epoxy primer). [for use on high contact /high traffic areas]Bituminous finish. [for use on low contact / low traffic areas, e.g. unexposed galvanized metalnext to concrete, masonry, etc.]Aluminum paint finish. [for use on low contact / low traffic areas only]Waterborne light industrial [insert gloss level] coating. [for moderate chemical resistance]Latex [insert gloss level] finish (over waterborne primer). [for low contact / low traffic areas - donot use flat finish on doors]Waterborne light industrial [insert gloss level] coating (over waterborne primer). [for moderatechemical resistance]Waterborne light industrial [insert gloss level] coating (over epoxy).Pigmented polyurethane finish (over epoxy primer).Aluminum: (sash, sills and frames, flashing, posts and railings, downpipes, etc.)EXT 5.4AEXT 5.4BEXT 5.4CEXT 5.4DEXT 5.4EEXT 5.4FEXT 5.4GEXT 5.4H.11Section 09900PaintingPage 6 of 15Alkyd [insert gloss level] finish.Pigmented polyurethane finish.Aluminum paint finish.Epoxy finish.Waterborne epoxy finish.Latex [insert gloss level] finish.Waterborne light industrial [insert gloss level] coating.Glue Laminated Beams and Columns:EXT 6.1AEXT 6.1BEXT 6.1CLatex [insert gloss level] finish (over alkyd primer).Alkyd [insert gloss level] finish.Solid color stain finish.The Master Painters Institute1997 - 2004
MPI Architectural Painting ManualShort Form Guide SpecificationRevision: June 2004EXT 6.1DEXT 6.1EEXT 6.1FEXT 6.1GEXT 6.1HEXT 6.1JEXT 6.1KEXT 6.1L.14Latex [insert gloss level] finish. [do not use flat finish on doors]Alkyd [insert gloss level] finish. [do not use flat finish on doors]Solid color stain finish. [do not use on high contact areas or on doors]Semi-transparent stain finish. [do not use on doors]Varnish [gloss] [semi-gloss] finish (over stain).Varnish [gloss] [semi-gloss] finish.Clear (2 component) polyurethane finish.Pigmented polyurethane finish.Waterborne light industrial [gloss] [semi-gloss] coating. [for doors and frames only]Waterborne solid color stain finish. [do not use flat for doors and frames]Latex [insert gloss level] finish (over latex primer). [do not use flat finish on doors]Wood Paneling: (plywood siding, fascias, soffits, etc.)EXT 6.4AEXT 6.4BEXT 6.4CEXT 6.4DEXT 6.4EEXT 6.4FEXT 6.4GEXT 6.4HEXT 6.4JEXT 6.4K.17Latex [insert gloss level] finish (over alkyd primer).Waterborne solid color stain finish.Alkyd [insert gloss level] finish.Solid color stain finish.Varnish [gloss] [semi-gloss] finish (over stain).Pigmented fire retardant [insert gloss level] coating.Clear fire retardant penetrating wood preservative coating.Clear (2 component) polyurethane finish.Pigmented polyurethane finish.Varnish [gloss] [semi-gloss] finish.Semi-transparent stain finish.Latex [insert gloss level] finish (over latex primer).Dressed Lumber: (doors, door and window frames, casings, battens, smooth facias, etc.)EXT 6.3AEXT 6.3BEXT 6.3CEXT 6.3DEXT 6.3EEXT 6.3FEXT 6.3GEXT 6.3HEXT 6.3JEXT 6.3KEXT 6.3L.16Varnish [gloss] [semi-gloss] finish (over stain).Clear (2 component) polyurethane finish (over stain).Pigmented fire retardant coating.Clear fire retardant penetrating wood preservative coating.Clear (2 component) polyurethane finish.Pigmented polyurethane finish.Varnish [gloss] [semi-gloss] finish.Latex [insert gloss level] finish (over latex primer).Dimension Lumber: (columns, beams, exposed joists, underside of decking, siding, fencing, etc.)EXT 6.2AEXT 6.2BEXT 6.2CEXT 6.2DEXT 6.2EEXT 6.2FEXT 6.2GEXT 6.2HEXT 6.2JEXT 6.2KEXT 6.2LEXT 6.2M.15Section 09900PaintingPage 7 of 15Waterborne solid color stain finish.Alkyd [insert gloss level] finish.Solid color stain finish.Semi-transparent stain finish.Pigmented fire retardant coating.Clear fire retardant penetrating wood preservative coating.Latex [insert gloss level] finish (over alkyd primer).Varnish [gloss] [semi-gloss] finish.Varnish [gloss] [semi-gloss] finish (over stain).Latex [insert gloss level] finish (over latex primer).Wood Decks and Stairs / Steps: (using spaced lumber)EXT 6.5AEXT 6.5BEXT 6.5CEXT 6.5DLatex porch and floor [gloss] [low gloss] finish [with anti-skid additive] (over alkyd primer).Alkyd floor enamel [gloss] [low gloss] finish [with anti-skid additive].Alkyd floor enamel [gloss] [low gloss] finish [with anti-skid additive] (over wood preservative).[for untreated wood].Deck stain (over wood preservative).The Master Painters Institute1997 - 2004
MPI Architectural Painting ManualShort Form Guide SpecificationRevision: June 2004EXT 6.5EEXT 6.5FEXT 6.5G.18Latex [insert gloss level] finishWaterborne light industrial [insert gloss level] coating.Elastomeric coating.Epoxy finish.Waterborne epoxy finish.Water repellent non-paintable finish.Water repellent paintable finish.High-build latex finish.Latex [insert gloss level] finish (over alkali resistant primer).Canvas and Cotton Coverings: (pipes, ductwork, etc.)EXT 10.1AEXT 10.1BEXT 10.1CEXT 10.1D.23Latex [insert gloss level] finish.Alkyd [insert gloss level] finish.Waterborne light industrial [insert gloss level] coating.Stucco: (walls and soffits)EXT 9.1AEXT 9.1BEXT 9.1CEXT 9.1DEXT 9.1EEXT 9.1FEXT 9.1GEXT 9.1HEXT 9.1J.22Latex [insert gloss level] finish.Alkyd [insert gloss level] finish.Waterborne light industrial [insert gloss level] coating.Pigmented polyurethane finish (over epoxy).Waterborne epoxy finish.Epoxy finish.Plastic: (vinyl siding and windows including related trims, ABS / PVA / PVC materials, fabrications, etc.)EXT 6.8AEXT 6.8BEXT 6.8C.21Latex [insert gloss level] finish (over alkyd primer).Alkyd [insert gloss level] finish.Solid color stain finish.Waterborne solid color stain finish.Latex [insert gloss level] finish (over latex primer).Semi-transparent stain finish.Fiberglass: (panels, trims, fabrications, etc.)EXT 6.7AEXT 6.7BEXT 6.7CEXT 6.7DEXT 6.7EEXT 6.7F.20Latex porch and floor [gloss] [low gloss] finish [with anti-skid additive] (over latex primer).Deck stain finish.Latex deck coating. [for plywood decks]Wood Shingles and Shakes: (excluding roofs)EXT 6.6AEXT 6.6BEXT 6.6CEXT 6.6DEXT 6.6EEXT 6.6F.19Section 09900PaintingPage 8 of 15Latex [insert gloss level] finish.Waterborne light industrial [insert gloss level] coating.Alkyd [insert gloss level] finish.Aluminum paint finish.Bituminous Coated Surfaces: (cast iron pipe, concrete, etc.)EXT 10.2AEXT 10.2BEXT 10.2CEXT 10.2DLatex [insert gloss level] finish.Latex [insert gloss level] [insert texture type] aggregate finish.Alkyd [insert gloss level] finish.Aluminum paint finish.The Master Painters Institute1997 - 2004
MPI Architectural Painting ManualShort Form Guide SpecificationRevision: June 20043.4Section 09900PaintingPage 9 of 15Interior Paint and Coating Systems:Paint interior surfaces in accordance with the following MPI Painting Manual requirements:.1Asphalt Surfaces: (zone / traffic marking of interior drive and parking areas)INT 2.1AINT 2.1B.2Concrete Vertical Surfaces: (including horizontal soffits)INT 3.1AINT 3.1BINT 3.1CINT 3.1DINT 3.1EINT 3.1FINT 3.1GINT 3.1HINT 3.1JINT 3.1KINT 3.1LINT 3.1MINT 3.1N.3Latex floor enamel [gloss] [low gloss] finish.Alkyd floor enamel [gloss] [low gloss] finish.Epoxy finish.Pigmented polyurethane finish.Concrete stain finish.Concrete floor sealer finish.Waterborne concrete floor sealer finish.Latex zone / traffic marking finish. [for parking lines, etc]Alkyd zone / traffic marking finish. [for parking lines, etc]Clear (2 component) polyurethane finish.Waterborne epoxy floor paint finish.Cementitious Composition Board Surfaces:INT 3.3AINT 3.3BINT 3.3CINT 3.3DINT 3.3EINT 3.3FINT 3.3GINT 3.3H.5Latex [insert gloss level] finish (over sealer).Latex [insert gloss level] finish over [insert texture type] latex aggregate.High performance architectural latex [insert gloss level] finish.Alkyd [insert gloss level] finish.Latex [insert gloss level] finish.Epoxy (tile-like) finish. [for smooth concrete]Waterborne epoxy (tile-like) finish. [for smooth concrete]Multicolor finish.Water repellent paintable finish.Concrete stain finish.Waterborne light industrial [insert gloss level] coating.Institutional low odor / low VOC [insert gloss level] finish.Latex [insert gloss level] [insert texture type] aggregate coating.Concrete Horizontal Surfaces: (floors and stairs)INT 3.2AINT 3.2BINT 3.2CINT 3.2DINT 3.2EINT 3.2FINT 3.2GINT 3.2HINT 3.2JINT 3.2KINT 3.2L.4Latex zone / traffic marking finish.Alkyd zone / traffic marking finish.Latex [insert gloss level] finish.High performance architectural latex [insert gloss level] finish.Alkyd [insert gloss level] finish.Waterborne epoxy (tile like) finish.Epoxy (tile like) finish.Multicolor finish.Institutional low odor / low VOC [insert gloss level] finish.Waterborne light industrial [insert gloss level] coating.Clay Masonry Units: (pressed and extruded brick)INT 4.1AINT 4.1BINT 4.1CINT 4.1DINT 4.1FINT 4.1GLatex [insert gloss level] finish.Latex [insert gloss level] [insert texture type] aggregate coating.Waterborne light industrial [insert gloss level] coating.Alkyd [insert gloss level] finish.Epoxy (tile like) finish. [for smooth brick]Waterborne epoxy (tile-like) finish. [for smooth brick]The Master Painters Institute1997 - 2004
MPI Architectural Painting ManualShort Form Guide SpecificationRevision: June 2004INT 4.1HINT 4.1JINT 4.1KINT 4.1LINT 4.1M.6Latex [insert gloss level] finish.Latex [insert gloss level] [insert texture type] aggregate coating.Alkyd [insert gloss level] finish.High performance architectural latex [insert gloss level] finish.Institutional low odor / low VOC [insert gloss level] finish.Epoxy (tile-like) finish. [for dry environments]Epoxy (tile-like) finish. [for wet environments]Multicolor finish.Waterborne epoxy (tile-like) finish. [for dry environments]Waterborne light industrial [insert gloss level] coating.Water repellent non-paintable finish. [do not use on light weight block]Water repellent paintable finish. [do not use on light weight block]Alkyd [insert gloss level] finish (over latex sealer).Structural Steel and Metal Fabrications: (columns, beams, joists, etc.)INT 5.1AINT 5.1BINT 5.1CINT 5.1CCINT 5.1DINT 5.1DDINT 5.1EINT 5.1FINT 5.1GINT 5.1HINT 5.1JINT 5.1KINT 5.1LINT 5.1MINT 5.1NINT 5.1PINT 5.1QINT 5.1RINT 5.1SINT 5.1TINT 5.1UINT 5.1VINT 5.1WINT 5.1XINT 5.1YINT 5.1Z.8Multicolor finish.Clear water repellent paintable finish.Clear (2 component) polyurethane finish.High performance architectural latex [insert gloss level] finish.Institutional low odor / low VOC [insert gloss level] finish.Concrete Masonry Units: (smooth and split face block and brick)INT 4.2AINT 4.2BINT 4.2CINT 4.2DINT 4.2EINT 4.2FINT 4.2GINT 4.2HINT 4.2JINT 4.2KINT 4.2LINT 4.2MINT 4.2N.7Section 09900PaintingPage 10 of 15Quick dry enamel [gloss] [semi-gloss] finish.Waterborne light industrial [insert gloss level] coating.Waterborne dry fall finish.Waterborne dry fall finish (over quick dry shop primer). [for dry locations only]Alkyd dry fall finish.Alkyd dry fall finish (over quick dry shop primer). [for dry locations only]Alkyd [insert gloss level] finish.Pigmented polyurethane finish (over epoxy primer).Pigmented polyurethane finish (over high-build epoxy).Pigmented polyurethane finish (over inorganic zinc primer and epoxy).Pigmented polyurethane finish (over epoxy zinc rich primer and epoxy).Waterborne epoxy finish.Epoxy finish.Aluminum paint finish.Waterborne light industrial [insert gloss level] coating (over epoxy primer).High build epoxy (over epoxy zinc rich primer).Latex [insert gloss level] finish (over alkyd primer).High performance architectural latex [insert gloss level] finish.Institutional low odor / low VOC [insert gloss level] finish.Alkyd [insert gloss level] finish (over surface tolerant primer).Epoxy finish (over self-priming epoxy).Pigmented polyurethane finish (over self-priming epoxy).Alkyd [insert gloss level] finish (over quick dry shop primer). [for dry locations only]Latex [insert gloss level] finish (over quick dry shop primer). [for dry locations only]Not applicableQuick dry shop paint finish (for dry locations only). [do not topcoat]Steel - High Heat: (boilers, furnaces, heat exchangers, breeching, pipes, flues, stacks, etc., with temperaturerange as noted)INT 5.2AINT 5.2BINT 5.2CINT 5.2DHeat resistant enamel finish, maximum 400 F (205 C).Heat resistant aluminum paint finish, maximum 800 F (427 C).Inorganic zinc rich coating, maximum 750 F (400 C).High heat resistant coating, maximum 1100 F (593 C).The Master Painters Institute1997 - 2004
MPI Architectural Painting ManualShort Fo
PART 1 - GENERAL SPEC NOTES:.1 Use this guide specification when a "short form" specification is required to specify painting and decorating work on new, previously unpainted surfaces.2 Refer to the MPI Architectural Manual "long form" painting specification for guidance and spec notes when using this specification. 1.1 Description:
