Transcription
DESCRIPTION/SUGGESTED SPECIFICATIONSSammyX-Press Installs intoMetal Deck,Purlin, orTubular SteelSammy X-Press Revolutionizes The PipeHanding Trades—The Sammy X-Press System is designed to provide direct attachment of threaded rod in metal deck(22-16 gauge) and thin gauge purlin (18-16 gauge), while providing reduced installation costs in termsof time and materials. The X-Press Anchors eliminate the need for costly “armovers” in pipe hanginginstallations. Current methods offered for thin gauge purlin require use of a time-consuming retainingnut on the threaded portion of the fastener to prevent pulloutand are not designed for use in metal deck. In many instances,access to the backside of the installed fastener is prohibitedby panel liner or roofing insulation. Sammy X-Press anchorsdeliver the performance installers require without the use of aretaining nut!The patent-pending X-Press Anchors consist of a threadedfastener and expandable sleeve. The X-Press System featuresan easy-to-install anchor with expanding anchoring strips that collapse to prevent pullout after installation.The Sammy X-Press It Installation Tool assures a perfect installation every time offering the added convenienceof one-tool efficiency – just drill and drive in seconds! SECONDS!Sammy X-PressADVANTAGESn Installs in seconds, saving time &installation costs.n Less jobsite material needed.n No retaining nut required.n Use in applications where access to the back ofthe installed fastener is prohibited. ie. metalroof deck, tubular steel, or vapor barrier fabric.n Provides design flexibility.Sammy’s X-Press, Swivel and SidewinderThe Sammy X-Press expands to providedirect vertical attachment in:- Metal Deck (22-16 gauge)(XP)Patent No.6,935,821- Z-Purlin (18-16 gauge)The Sammy X-Press Swivel allows you tohang plumb in extreme roof pitches:(SWXP)Patent Pending(SXP)Patent PendingCall our toll free number 800-387-9692 or visit www.itwconstruction.ca for general information.- 89 in Z-Purlin- 45 in metal deck for 12/12 pitchThe Sammy X-Press Sidewinder expandsto provide horizontal attachment in:- 16 ga - 3/16" steel - purlin, tubular steel.
Sammy X-PressAPPROVALSAPPLICATIONSSprinkler SystemsThe X-Press System has earned the 9R21 and 25ES UL Listing.Pipes/PlumbingElectrical Lighting and FixturesHVAC Equipment and FixturesINSTALLATION TOOLINSTALLATION INSTRUCTIONSSAMMY X-PRESS IT INSTALLATION TOOLUXPITPatent Pending1. Pre-Drill.2. I nsert Anchor.3. PIT*Universal X-Press It Tool18152910XPDB25/64" Drill Bit1*Tool Includes: Sleeve, Bit Receiver, Hex Wrench, and 25/64” Drill Bit.Call our toll free number 800-387-9692 or visit www.itwconstruction.ca for general information.
Sammy X-PressSELECTION CHARTSAMMYS X-Press Vertical MountULTIMATEROD PARTSIZE NUMBER MODEL DESCRIPTION PULLOUT(LBS)1/4"8181922XP 200X-Press 2001146(22 ga)3/8"8150922XP 20X-Press 201146(22 ga)3/8"8153922XP 35X-Press 351783(16 ga)3/8"8150922XP 20X-Press 201146(22 ga)(XP)Patent No.6,935,821TESTMINLOAD UL(LBS) THICK185 (Luminaire)250 (Luminaire)850 (2½" Pipe)185 (Luminaire)250 (Luminaire)283 (Conduit & Cable)1500 (4" Pipe)85 (Luminaire)250 (Luminaire)416 (Conduit & Cable)TESTMIN MAXLOAD FM(LBS) THICK 29”.056”.059”940 (2" Pipe)1475 (4” Pipe)940 (2" Pipe)1475 (4” Pipe)BOXQTYCASEQTYAPPLICATION.125”25125Metal Deck.029”.104”.125”25125Metal Deck.029”.104”.125”25125Purlin25125Metal Deck(Pre-Pour)Metal Deck(Post-Pour)Pre-Pour Structural Concrete@ 3000 psiPost-Pour Range II LWC 35 PCF (lbs/ ft³)850 (2½ Pipe)Pre-Pour Structural Concrete @ 3000 psiPost-Pour Range II LWC 35 PCF (lbs/ ft³)SAMMYS X-Press Swivel Head ULTIMATEPULLOUT(LBS)ROD PARTSIZE NUMBER MODEL DESCRIPTION(SXP)3/8"Patent Pending8295922SXP 35SwivelX-Press 35TESTMINLOAD UL(LBS) THICK1250 (3-1/2" Pipe)250 vertical (Luminaire)167580 @ 90 (Luminaire)(16 ga Vertical)500 vertical1558(Conduit & Cable)(89 Off Vertical)333 @ 89 (Conduit & Cable).059”TESTMIN MAXLOAD FM(LBS) THICK THICK635 (2" Pipe).029".125”BOX CASE APPLICATIONQTY QTY25125PurlinSAMMYS X-Press Horizontal MountRODPARTSIZE NUMBER MODELPatent Pending3/8"8293957SWXP 35DESCRIPTIONSidewinderX-Press 35(SWXP)Call our toll free number 800-387-9692 or visit www.itwconstruction.ca for general information.ULTIMATEPULLOUT(LBS)1798 (16 ga)TESTLOAD(LBS)1250 (3½" Pipe)80 (Luminaire)416 (Conduit & Cable)TEST MINLOAD 125”25125Purlin
SAMMYS X-Pressfor SeismicRestraintDESCRIPTIONFEATURESn Structural attachment andrestraint component combined;ready for selected rod.n Access to the back of fastenernot required.n Does not require use of aretaining nut.n Quick and easy installation.FOR 3/8" AND 1/2" RODSBENEFITSn Reduced installation cost.n Design flexibility.n Less on site material (GO GREEN).n Less material coordination.n Aesthetically pleasing.SPECIFICATIONSSXP 35 FOR 3/8" RODStructural attachment for installation of branch/end of line restraint using3/8" all thread (.299” OD) or end thread rod (.374” OD).SXP 35 for 3/8" Rod: Designed for use in steel purlin ranging from 16 ga.through 1/8" in low slope or pitched roof designs (12/12).The Swivels may be used to attach short length of rod to eliminate lateralsway bracing per NFPA 13, 9.3.5.3.8, (2007).FOR 3/8" RODRestrained Pipe Size: Up to Schedule 40 pipe 2" or lessMax Length ofSee Maximum Horizontal Load Tables below.Restraint Material:Maximum Angle:45 from horizontalCarbon SteelMaterial:1/4"-20 x 1-1/8" with expandable sleeveScrew Description:Finish:Electro-ZincTested to GR-63-CORE Standard for performance inTesting:structural steel in seismic restraint applications as outlined for use in NFPA 13 (2007),9.3 at an independent test lab. The calculated force used for the testing was equal tothat found in a Zone 4 and an 8.4 Richter scale seismic event.Listing for 3/8" Rod:UL 203 listed as pipe hanger File EX 5098- SXP 35 (16 ga.) 0-90 from horizontal - 3-1/2" Schedule 40 pipeUL 203A File EX 15565SELECTION CHARTSAMMYS X-Press Swivels – Seismic RestraintRODSIZEPARTNUMBERMODEL3/8"8295922SXP 35MINTHICKNESS16 gaMAXTHICKNESSAPPLICATIONBOXQTYCASEQTYINSTALLATION TOOLPurlin25125The SWXP 35 must be installedwith UXPIT Tool (Part No. 8194910);pre-drilling required.1/8"PERFORMANCE TABLESMaximum Rod Length for l/r 100, 200, 300, and 400RESTRAINT SHAPE AND SIZERods (all thread)Rods (threaded at ends only)Reference: NFPA 13, (2007)NOMINAL DIAMETER3/8 in.1/2 in.3/8 in.1/2 in.* Reference: NFPA 13, (2010)AREA (in.2)LEAST RADIUS OFGYRATION, r (in.)0.070.1290.110.1960.0750.1010.0940.125MAXIMUM ROD LENGTH FOR l/r (ft)l/r 1000.60.80.81.0l/r 2001.31.71.62.1l/r 3001.92.52.43.1l/r 400*2.53.43.14.2Call our toll free number 800-387-9692 or visit www.itwconstruction.ca for general information.
SAMMYS X-Press for Seismic RestraintDESCRIPTION (SIDEWINDER)SWXP 35 FOR 3/8" RODStructural attachment for installation of branch/end of line restraint using3/8" threaded rod. Used primarily in purlin, bar joist, or other steel structuralmembers. These fastening systems provide a secure and economical attachmentto the structure.The SWXP 35 model provides upper structural attachment in a range of steelthicknesses, from 16 ga. through 1/8". An expandable sleeve is included witheach fastener, eliminating need for retaining nut.SPECIFICATIONSRestrained Pipe Size:Up to Schedule 40 pipe 2" or lessMax Length ofRestraint Material:See Maximum Horizontal Load Tables below.Maximum Angle:45 from horizontalMaterial:Carbon SteelScrew Description:1/4"-20 X 1-1/8" with expandable sleeveFinish:Electro-Zinc (cap & screw)Testing:BX Report # R-1362Listing:UL 203 as a pipe hangerUL 203A pendingSELECTION CHARTSAMMYS Sidewindersfor Steel – Seismic ODELSWXP 3516 ATION TOOLSteel Purlin or Bar Joist25125The SWXP 35 must be installedwith UXPIT Tool (Part No. 8194910);pre-drilling required.PERFORMANCE TABLESMaximum Horizontal Loads forRestraint with l/r 100, 200, 300, and 400RESTRAINT SHAPE AND SIZERods (all thread)Rods (threaded at ends only)Reference: NFPA 13, (2007)NOMINALDIAMETERAREA (in.2)LEAST RADIUS OFGYRATION, r (in.)3/8 in.1/2 in.3/8 in.1/2 in.0.070.1290.110.1960.0750.1010.0940.125* Reference: NFPA 13, (2010)Call our toll free number 800-387-9692 or visit www.itwconstruction.ca for general information.l/r 1000.60.80.81.0MAXIMUM ROD LENGTH FOR l/r (ft)l/r 200l/r 300l/r 400*1.31.92.51.72.53.41.62.43.12.13.14.2
Sammy X-Press Sammy's X-Press, Swivel and Sidewinder (XP) Patent No. 6,935,821 (SXP) Patent Pending (SWXP) Patent Pending The Sammy X-Press expands to provide direct vertical attachment in: - Metal Deck (22-16 gauge) - Z-Purlin (18-16 gauge) The Sammy X-Press Swivel allows you to hang plumb in extreme roof pitches: - 89 in Z-Purlin
