Transcription
NS1USER MANUAL
WELCOME2Congratulations on your purchase of the Ventum NS1, your Aero All-RoadPerformance Bike! Get ready to experience a bike that is totally unlike anyother on the road today. Your new Ventum NS1 combines forward thinkingdesign with the most advanced technologies available, to shatter thenotion that a road bike can be either lightweight or aerodynamic.This document will guide you through the process of setting up your newbike and getting out on the road. Of course, if you have any questions or ifwe can be of assistance in any way, please contact the Ventum Conciergeteam at support@ventumracing.com. Before you hit the road, please alsotake a moment to register your bike purchase via our website.3
4CONTENTSFRAME DIAGRAM.6UNBOXING.8WHEEL REMOVAL.10SEAT POST INSTALLATION.12FRAME UNBOXING.16WHEEL INSTALLATION.18FINAL CHECKS & ROAD TEST.225
6FRAME DIAGRAMPlease carefully inspect the image. It gives you a thorough break down ofthe names of the tubes that the frame/ fork consist of and the componentsthat this bike uses. Please refer back to this image as needed.1Top Tube13Handle Bar2Fork14Brake Lever3Head Tube15Rear Derailleur4Down Tube16Cassette5Chain Stay17Chain6Seat Stay18Crank7Seat Tube19Front Derailleur8Seat Post20Brake Caliper9Saddle21Brake Rotor10Seat Post Clamp22Tire11HeadSet 72223
UNBOXINGRemove the parts box and support cover8UNBOXINGRemove the top tube foam blocks and shifter blocks9
WHEEL REMOVALRemove the straps and foam blocks from the wheels10WHEEL REMOVALRemove the wheels from the box and remove the hub guards11
SEAT POST INSTALLATION1. Detach the seat post and remove the protective foam2. Undo the strap around the bottom bracket12SEAT POST INSTALLATION13
SEAT POST INSTALLATION14SEAT POST INSTALLATION1. Plug Di2 cable into seat post battery, you should hear a click.2. Insert the seat post into the frame. Ensure the minimum insertion depthof 10 cm is achieved.3. Torque the seat post clamp bolt to a minimum of 8 N.m. Temperature,moisture, and contaminants can affect the seat post clamp. If necessary,it can be torqued up to 10 N.m.NOTE: To remove or adjust the seat post, loosen the seat post clamp bolt.It is not necessary to remove it from the clamp entirely. Simultaneouslytap the tail and nose of the saddle with your hands to disengage theclamp’s grip on the seat post and permit adjustment. Push or pull theseat post as required to achieve the desired saddle height.WARNINGFAILURE TO FOLLOW THESE INSTRUCTIONS COULD LEAD TO SERIOUS INJURY OR DEATH.STEP 1STEP 315
FRAME UNBOXINGRemove the straps from the handlebar16FRAME UNBOXING1. Lift the frame out of the box2. Detach the strap and foam block from the crank arm17
WHEEL INSTALLATIONUnscrew the thru axles from the frame and fork using a 6mm hex tool18WHEEL INSTALLATIONRemove the spacers from the brake calipers19
WHEEL INSTALLATIONInstall the wheels ensuring the rotor lines up between the brake pads20WHEEL INSTALLATION21Secure the wheels by re-installing the thru axles. Torque to 12 N.m.WARNINGFAILURE TO FOLLOW THESE INSTRUCTIONS COULD LEAD TO SERIOUS INJURY OR DEATH.
FINAL CHECKS & ROAD TEST221. Install your pedals as per the manufacturer’s instructions.2. Check the tire pressure and inflate as per the manufacturer’srecommendation.3. Adjust the saddle height as necessary. Ensure the seat post minimuminsertion depth of 10 cm is achieved.4. Put on your shoes and helmet and take your new bike out for a roadtest. Always wear a helmet when you ride your bicycle.5. Check the operation of the brakes, derailleurs, and steering.WARNINGFAILURE TO FOLLOW THESE INSTRUCTIONS COULD LEAD TO SERIOUS INJURY OR DEATH.23ENJOY YOUR NEW RIDE!
VENTUMRACING.COM
Congratulations on your purchase of the Ventum NS1, your Aero All-Road Performance Bike! Get ready to experience a bike that is totally unlike any other on the road today. Your new Ventum NS1 combines forward thinking design with the most advanced technologies available, to shatter the notion that a road bike can be either lightweight or .
