Transcription
DESIGNINTENTDRAWINGSNIRPC Unified TrailWayfindingAugust 2016Northwestern IndianaRegional Planning Commision (NIRPC)6100 Southport RoadPortage, Indiana 46368Contact: Mitch Barloga, AICPPhone: 219.763.6060 x133Fax: 219.762.1653TABLE OF CONTENTSThe purpose of these drawings is to illustrate design intent. Drawings are not forconstruction. Written dimensions on these drawings have precedence over scaleddimensions.The further development and engineering of these drawings shall be submitted asshop drawings to the Project Owner. Contractors shall verify and be responsiblefor all final quality, dimensions, materials and conditions on the job.Project owner shall be notified of any variations from the dimensions andconditions shown by these drawings prior to the execution of any work, includingchanges to graphic designs or typography.Drawing scale shown on plans is for full size plans only. Alta shall not beresponsible for scale discrepancies caused by reduced or enlarged drawings.Graphic Standards2System Overview3Welcome Sign4Vehicular Trailhead5Map Kiosk6Pedestrian Directional Sign7Pedestrian Regulatory Sign8Alta Planning DesignMile Marker9800 S Broadway, 2nd Floor FrontBaltimore, MD 21231ph: 443.218.8165
MATERIALS PALETTEContractor shall be responsible for supplying samples for all colors and materials within the palette.ng i seD gn i nna l P a t l A800 S Broadway,Baltimore, MD 21231ph: reenGDark GreenBBlueBDark BlueWr White - ReflectiveWhitePantone: 425 CColor match: CMYK (46%, 0%, 85%, 0%)Color match: CMYK (65%, 23%, 100%, 6%)Color match: CMYK (53%, 1%, 27%, 0%)Color match: CMYK (86%, 34%, 56%, 14%)WhiteMatthews PaintMatthews PaintMatthews PaintMatthews PaintMatthews PaintMatthews Paint3M 3930 High Intensity RetroreflectiveSurface painted, with MatthewsPolyurethane Clear Coat ProtectantSurface painted, with MatthewsPolyurethane Clear Coat ProtectantSurface painted, with MatthewsPolyurethane Clear Coat ProtectantSurface painted, with MatthewsPolyurethane Clear Coat ProtectantSurface painted, with MatthewsPolyurethane Clear Coat ProtectantSurface painted, with MatthewsPolyurethane Clear Coat ProtectantSStoneGENERAL NOTES·These drawings are intended to illustratedesign intent only and are not forconstruction. All final engineering andconditions of the project are theresponsibility of the fabricator. Shopdrawings by the fabricator must besubmitted for approval, prior to proceedingwith fabrication.·The quality of fit and finish on the finalproduct must meet or exceed therequirements of these design intentdocuments. Any variations to design,materials, or fabrication methods must beapproved by the Owner or Representive.·Welds: All welds shall be ground smooth,paint all seams.·Hardware: All exposed hardware shall betamper proof fasteners.·All exposed edges painted to matchadjacent face.·Colors shown are for reference only andare subject to the limitations of the printingprocess. Refer to referenced color systemscontained within these drawings for actualspecifications.·Scaled examples shown are for referenceonly, and do not necessarily reflect actualsite conditions. Detailed site surveys arerequired prior to fabrication and installation.·Messages shown in these drawings are forgeneral reference only. Refer to messageschedules for actual required messages.TYPOGRAPHYFabricator is responsible for acquiring project related fonts.Highway GothicAa Bb Cc Dd Ee Ff Gg Hh Ii Jj Kk Ll Mm Nn Oo Pp Qq Rr Ss Tt Uu Vv Ww Xx Yy Zz 1234567890Highway Gothic WideAa Bb Cc Dd Ee Ff Gg Hh Ii Jj Kk Ll Mm Nn Oo Pp Qq Rr Ss Tt Uu Vv Ww Xx Yy Zz 1234567890ARTWORKAll artwork illustrated on this page shall be provided by Project Owner as electronic vector art.Contractor is responsible formatching all colors and materialsas specified and are required toprovide color and material sampleto the Project Owner for approval.Northwest Indiana Greenways& Blueways LogoPraire Grass SilhouetteCalumet Trail LogoDunes Kankakee Trail LogoGary Green Link LogoChesapeake and Ohio Greenway LogoAll painted surfaces to receive UVand Anti-Graffitti coating. Allretroreflective material to receiveUV/Anti-Graffiti overlaminate, orowner approved equal.American Discovery Trail LogoThe Marquette Greenway LogoOak Savannah Trail LogoNo substitute typefaces will beaccepted. Set kerning tracks tovisually approximate signdrawings. Kerning shown mayvary from exact kerning used tocreate sign drawings. Refer tospecific applications for type sizesand leading requirements.Northwestern IndianaRegional Planning CommissionCLIENTNIRPC Unified Trail WayfindingPROJECT08 August 2016DOCUMENT ISSUEGraphic StandardsSHEET TITLE2Destination Travel Distance & TimesTypical ArrowVeterans Memorial Parkway LogoPrarie Duneland Trail LogoSHEET NUMBER
ng i seD gn i nna l P a t l A800 S Broadway,Baltimore, MD 21231ph: 443.218.8165GENERAL NOTESYCIT GOLOWELCOME TOCITY NAMENAME1NAME2TRAILHEADCross-streetNameTYCI GOLOWelcome toCity NameCity of NameYCITGOLOYCIT GOLO·These drawings are intended to illustratedesign intent only and are not forconstruction. All final engineering andconditions of the project are theresponsibility of the fabricator. Shopdrawings by the fabricator must besubmitted for approval, prior to proceedingwith fabrication.·The quality of fit and finish on the finalproduct must meet or exceed therequirements of these design intentdocuments. Any variations to design,materials, or fabrication methods must beapproved by the Owner or Representive.·Welds: All welds shall be ground smooth,paint all seams.·Hardware: All exposed hardware shall betamper proof fasteners.·All exposed edges painted to matchadjacent face.·Colors shown are for reference only andare subject to the limitations of the printingprocess. Refer to referenced color systemscontained within these drawings for actualspecifications.·Scaled examples shown are for referenceonly, and do not necessarily reflect actualsite conditions. Detailed site surveys arerequired prior to fabrication and installation.·Messages shown in these drawings are forgeneral reference only. Refer to messageschedules for actual required messages.YCIT GOLOWELCOME SIGNVEHICULARTRAILHEADMAP KIOSKPEDESTRIANDIRECTIONALPEDESTRIANREGULATORYMILE MARKERNorthwestern IndianaRegional Planning CommissionCLIENTNIRPC Unified Trail WayfindingPROJECT08 August 2016DOCUMENT ISSUESystem OverviewSHEET TITLE3SHEET NUMBER
KEY NOTESEQEQCLDrill & epoxy1. LIMESTONE SIGN4'-6" L x 2'-4" W x 5" thickMATERIAL: Indiana limestoneASTM C568, Type II, Medium density limstoneSteel dowels, weld toH beam, spacing, length& size per engineer2. STEEL HEADERStructural steel H beam, W 6 X15 lb (5.99" x.230" web x 5.99"). 1/2" fillet on all cornersCL5"1Type: Highway Gothic,4" high21'Spacer materialType: Highway Gothic,6" high4" x 6" steel platewelded to lower halfof H-beam, typ both ends(shown larger for clarity)5"3EQ3EQSign Layout4'-6"110 1/2"CL1'1'B329. CITY LOGOMATERIAL: 8" dia x 1/4" thk. aluminumFABRICATION PROCESS: Router CutEDGES: Routed, finished smoothFASTENER: Pin mountedGRAPHICS/TEXT: digitally printed31'4"1'242'10"2" typ2" typ5YCIT GOLO10. CONCRETE FOOTINGConcrete footing to engineer's specifications11. ENGRAVINGSandblasted 'Prairie Grass' silhouette10·The quality of fit and finish on the finalproduct must meet or exceed therequirements of these design intentdocuments. Any variations to design,materials, or fabrication methods must beapproved by the Owner or Representive.·Welds: All welds shall be ground smooth,paint all seams.·Hardware: All exposed hardware shall betamper proof fasteners.·All exposed edges painted to matchadjacent face.·Colors shown are for reference only andare subject to the limitations of the printingprocess. Refer to referenced color systemscontained within these drawings for actualspecifications.·Scaled examples shown are for referenceonly, and do not necessarily reflect actualsite conditions. Detailed site surveys arerequired prior to fabrication and installation.·Messages shown in these drawings are forgeneral reference only. Refer to messageschedules for actual required messages.8. TRAIL LOGOMATERIAL: 12" dia x 1/4" thick aluminumFABRICATION PROCESS: Router CutEDGES: Routed, finished smoothFASTENER: Pin mountedGRAPHICS/TEXT: digitally printed3BThese drawings are intended to illustratedesign intent only and are not forconstruction. All final engineering andconditions of the project are theresponsibility of the fabricator. Shopdrawings by the fabricator must besubmitted for approval, prior to proceedingwith fabrication.4. LIMESTONE CAPSmooth top and bottom, rock face sides.SIZE: 5'-4" L x 1'-8" W x 4" H7. GREENWAYS & BLUEWAYS LOGOMATERIAL: 8" dia x 1/4" thick aluminumFABRICATION PROCESS: Router CutEDGES: Routed, finished smoothFASTENER: Pin mountedGRAPHICS/TEXT: digitally printed6CITY NAME113. SUPPORT POSTSquare A500 steel tube, 4 x 4 x 3/8" wall.Embedded into monument wall and welded tosteel header·6. LETTERING1/2" thick aluminum letters, pin-mounted 1/2"from face of sign1'2'-4"#GENERAL NOTES5. MONUMENT WALLSIZE: 5-0" L x 1'-4" W x 1'-8" HLimestone natural stone veneer, depth 1-1/4"nominal (3/4" to 1-1/2"), color to match signFABRICATION: Standard masonaryconstructionScale: 3/4" 1'-0"5"WELCOME TO5'-6"Detail - Sectionng i seD gn i nna l P a t l A800 S Broadway,Baltimore, MD 21231ph: 443.218.8165Northwestern IndianaRegional Planning CommissionCLIENTNIRPC Unified Trail WayfindingPROJECT08 August 2016DOCUMENT ISSUE78195'1'-4"Welcome Sign5'-4"1'-8"SHEET TITLEFront ElevationScale: 3/4" 1'-0"2Side Elevation4Scale: 3/4" 1'-0"SHEET NUMBER
KEY NOTES1. ALUMINUM SLEEVE & FRAMEMATERIAL: 1/8" thick aluminumFabricated alumimum sheet sign face andback, fully welded and fabricated sides with alledges and corners neatly finishedFRAME: Fabricated aluminum channel internalstructure to engineer's specification. Frame tobe set inside perimeter of sign sleeve2'EQ2. TRAIL LOGOMATERIAL: 12" dia x 1/4" thick aluminumFABRICATION PROCESS: Router CutEDGES: Routed, finished smoothFASTENER: adhesiveGRAPHICS/TEXT: digitally printed8"CLEQng i seD gn i nna l P a t l A800 S Broadway,Baltimore, MD 21231ph: 443.218.8165GENERAL NOTES·These drawings are intended to illustratedesign intent only and are not forconstruction. All final engineering andconditions of the project are theresponsibility of the fabricator. Shopdrawings by the fabricator must besubmitted for approval, prior to proceedingwith fabrication.·The quality of fit and finish on the finalproduct must meet or exceed therequirements of these design intentdocuments. Any variations to design,materials, or fabrication methods must beapproved by the Owner or Representive.·Welds: All welds shall be ground smooth,paint all seams.·Hardware: All exposed hardware shall betamper proof fasteners.·All exposed edges painted to matchadjacent face.·Colors shown are for reference only andare subject to the limitations of the printingprocess. Refer to referenced color systemscontained within these drawings for actualspecifications.·Scaled examples shown are for referenceonly, and do not necessarily reflect actualsite conditions. Detailed site surveys arerequired prior to fabrication and installation.·Messages shown in these drawings are forgeneral reference only. Refer to messageschedules for actual required messages.11'3. RAISED LETTERINGMATERIAL: 1/2" thick aluminumEDGES: Routed, finished smoothFASTENER: adhesive3'-10"26"7'-8"4NAME1NAME2TRAILHEAD3Type: Highway Gothic,4" high5TYCI GOLOTYCI GOLO5. CITY LOGOMATERIAL: 8" dia x 1/4" thick aluminumFABRICATION PROCESS: Router CutEDGES: Routed, finished smoothFASTENER: adhesiveGRAPHICS/TEXT: digitally printed6. DIGITAL PRINTDigitally printed 'Praire Grass' silhouette andstone texture (not shown)7. CONCRETE FOOTINGConcrete footing to engineer's specifications.Conceal hold down bolts within sign structure10"2'-8"Northwestern IndianaRegional Planning CommissionCLIENTS6NIRPC Unified Trail WayfindingPROJECT708 August 20164"8'6"6"NAME1NAME2TRAILHEADW4. GREENWAYS & BLUEWAYS LOGOMATERIAL: 8" dia x 1/4" thick aluminumFABRICATION PROCESS: Router CutEDGES: Routed, finished smoothFASTENER: adhesiveGRAPHICS/TEXT: digitally printedDOCUMENT ISSUEVehicular Trailhead SignSHEET TITLE1Front ElevationScale: 3/4" 1'-0"2Side ElevationScale: 3/4" 1'-0"3Rear Elevation5Scale: 3/4" 1'-0"SHEET NUMBER
KEY NOTES1. TRAIL LOGOMATERIAL: 12" dia x 1/4" thk. aluminumFABRICATION PROCESS: Router CutEDGES: Routed, finished smoothFASTENER: adhesiveGRAPHICS/TEXT: digitally printed2'-8"EQ2. GREENWAYS & BLUEWAYS LOGOMATERIAL: 6" dia x 1/4" thk. aluminumFABRICATION PROCESS: Router CutEDGES: Routed, finished smoothFASTENER: adhesiveGRAPHICS/TEXT: digitally printed10"EQ3. CITY LOGOMATERIAL: 6" dia x 1/4" thk. aluminumFABRICATION PROCESS: Router CutEDGES: Routed, finished smoothFASTENER: adhesiveGRAPHICS/TEXT: digitally printed8"4"2"15"SYCIT GOLO29YCIT GOLO34555. MAP PANEL:MATERIAL: Non-glare clear acrylic panel, highpressure laminate map panel.ARTWORK: Directory map shown forreference only. Map with all associated textsand pictograms to be provided in digital format.FASTENER: (6) six stainless steel Ø1-1/2" x 1"length stand-offs, tamper-proofInformation(optional)GENERAL NOTES·These drawings are intended to illustratedesign intent only and are not forconstruction. All final engineering andconditions of the project are theresponsibility of the fabricator. Shopdrawings by the fabricator must besubmitted for approval, prior to proceedingwith fabrication.·The quality of fit and finish on the finalproduct must meet or exceed therequirements of these design intentdocuments. Any variations to design,materials, or fabrication methods must beapproved by the Owner or Representive.·Welds: All welds shall be ground smooth,paint all seams.·Hardware: All exposed hardware shall betamper proof fasteners.·All exposed edges painted to matchadjacent face.·Colors shown are for reference only andare subject to the limitations of the printingprocess. Refer to referenced color systemscontained within these drawings for actualspecifications.·Scaled examples shown are for referenceonly, and do not necessarily reflect actualsite conditions. Detailed site surveys arerequired prior to fabrication and installation.·Messages shown in these drawings are forgeneral reference only. Refer to messageschedules for actual required messages.7'6'-8"4'TOP ZONE:Trail map4. ALUMINUM SLEEVE & FRAMEMATERIAL: 1/8" thick aluminumFabricated alumimum sheet sign face andback, fully welded and fabricated sides with alledges and corners neatly finishedFRAME: Fabricated aluminum channel internalstructure to engineer's specification. Frame tobe set inside perimeter of sign sleeveng i seD gn i nna l P a t l A800 S Broadway,Baltimore, MD 21231ph: 443.218.81656. LOCATION PANELMATERIAL: 1/8" thick aluminumEDGES: Routed, finished smoothFASTENER: adhesiveGRAPHICS/TEXT: digitally printed3" margin on both sides2"BOTTOM ZONE:Rules & RegulationsG6Location panel(optional)3"1'-10"City of Name7. DIGITAL PRINTDigitally printed 'Praire Grass' silhouette andstone texture (not shown)1"S8. CONCRETE FOOTINGConcrete footing to engineer's specifications.Conceal hold down bolts within sign structure79. LOGO TOP PANELMATERIAL: 1/8" thick aluminumFASTENER: welded4"8Northwestern IndianaRegional Planning CommissionCLIENTNIRPC Unified Trail WayfindingPROJECT08 August 2016DOCUMENT ISSUEMap KioskSHEET TITLE1Front ElevationScale: 3/4" 1'-0"2Side ElevationScale: 3/4" 1'-0"3Rear Elevation6Scale: 3/4" 1'-0"SHEET NUMBER
1 3/4"KEY NOTES1'-8"CL2 1/2"3/4"4 3/4"2 1/4"10"Type: Highway Gothic Wide,1-1/2" highType: Highway Gothic,3/4" high5 3/4"Destination Panel Layout1'-10"8"4"2"B2"2"Cross-streetNameWelcome toCity Name2"6"6"Destination panel,total of 32. DESTINATION PANELPanel wraps around sleeveMATERIAL: 1/8" thick aluminumFABRICATION PROCESS: Router cutEDGES: Routed, finished smoothFASTENER: adhesiveGRAPHICS/TEXT: digitally printed3. LOCATION PANELPanel wraps around sleeveMATERIAL: 1/8" thick aluminumFABRICATION PROCESS: Router cutEDGES: Routed, finished smoothFASTENER: adhesiveGRAPHICS/TEXT: digitally printed4. WELCOME PANELPanel wraps around sleeveMATERIAL: 1/8" thick aluminumFABRICATION PROCESS: Router cutEDGES: Routed, finished smoothFASTENER: adhesiveGRAPHICS/TEXT: digitally printedGG55. GREENWAYS & BLUEWAYS LOGOMATERIAL: 4" dia x 1/4" thk. aluminumFABRICATION PROCESS: Router CutEDGES: Routed, finished smoothFASTENER: adhesiveGRAPHICS/TEXT: digitally printed34Cross-streetNameLocation Panel(optional)Welcome toCity NameWelcome Panel(optional)61'-8"TYCI GOLO2'-2"22"10"10"10"16'-8"TYCI GOLO7S6. TRAIL LOGOMATERIAL: 4" dia x 1/4" thk. aluminumFABRICATION PROCESS: Router CutEDGES: Routed, finished smoothFASTENER: adhesiveGRAPHICS/TEXT: screen printed7. CITY LOGOMATERIAL: 4" dia x 1/4" thk. aluminumFABRICATION PROCESS: Router CutEDGES: Routed, finished smoothFASTENER: adhesiveGRAPHICS/TEXT: digitally printed88. DIGITAL PRINTDigitally printed 'Praire Grass' silhouette andstone texture (not shown)94"7'2"1. ALUMINUM SLEEVE & FRAMEMATERIAL: 1/8" thick aluminumFabricated alumimum sheet sign face andback, fully welded and fabricated sides with alledges and corners neatly finishedFRAME: Fabricated aluminum channel internalstructure to engineer's specification. Frame tobe set inside perimeter of sign sleeveng i seD gn i nna l P a t l A800 S Broadway,Baltimore, MD 21231ph: 443.218.8165GENERAL NOTES·These drawings are intended to illustratedesign intent only and are not forconstruction. All final engineering andconditions of the project are theresponsibility of the fabricator. Shopdrawings by the fabricator must besubmitted for approval, prior to proceedingwith fabrication.·The quality of fit and finish on the finalproduct must meet or exceed therequirements of these design intentdocuments. Any variations to design,materials, or fabrication methods must beapproved by the Owner or Representive.·Welds: All welds shall be ground smooth,paint all seams.·Hardware: All exposed hardware shall betamper proof fasteners.·All exposed edges painted to matchadjacent face.·Colors shown are for reference only andare subject to the limitations of the printingprocess. Refer to referenced color systemscontained within these drawings for actualspecifications.·Scaled examples shown are for referenceonly, and do not necessarily reflect actualsite conditions. Detailed site surveys arerequired prior to fabrication and installation.·Messages shown in these drawings are forgeneral reference only. Refer to messageschedules for actual required messages.Northwestern IndianaRegional Planning CommissionCLIENTNIRPC Unified Trail WayfindingPROJECT08 August 2016DOCUMENT ISSUE9. CONCRETE FOOTINGConcrete footing to engineer's specifications.Conceal hold down bolts within sign structureNote: Left side similiar but w/osigns wrapped aroundPedestrian Directional SignSHEET TITLE1Front ElevationScale: 3/4" 1'-0"2Right Side ElevationScale: 3/4" 1'-0"3Rear Elevation7Scale: 3/4" 1'-0"SHEET NUMBER
KEY NOTES1. SIGN PANELMATERIAL: 1/8" thick aluminumFABRICATION PROCESS: Router cutEDGES: Routed, finished smoothFASTENER: adhesiveGRAPHICS/TEXT: digitally printedng i seD gn i nna l P a t l A800 S Broadway,Baltimore, MD 21231ph: 443.218.8165GENERAL NOTES·These drawings are intended to illustratedesign intent only and are not forconstruction. All final engineering andconditions of the project are theresponsibility of the fabricator. Shopdrawings by the fabricator must besubmitted for approval, prior to proceedingwith fabrication.·The quality of fit and finish on the finalproduct must meet or exceed therequirements of these design intentdocuments. Any variations to design,materials, or fabrication methods must beapproved by the Owner or Representive.·Welds: All welds shall be ground smooth,paint all seams.·Hardware: All exposed hardware shall betamper proof fasteners.·All exposed edges painted to matchadjacent face.·Colors shown are for reference only andare subject to the limitations of the printingprocess. Refer to referenced color systemscontained within these drawings for actualspecifications.·Scaled examples shown are for referenceonly, and do not necessarily reflect actualsite conditions. Detailed site surveys arerequired prior to fabrication and installation.·Messages shown in these drawings are forgeneral reference only. Refer to messageschedules for actual required messages.2. GREENWAYS & BLUEWAYS LOGOMATERIAL: 8" dia x 1/4" thk. aluminumFABRICATION PROCESS: Router CutEDGES: Routed, finished smoothFASTENER: welded to post cap3. WOOD POSTMATERIAL: 4" x 4" pressure treated woodINSTALLATION: 30" min. bury or surfacemount per engineer's specificationsTypical sign, variesYCIT GOLO1 1/2" min.5 1/2"4. POST BRACKETMATERIAL: steel, design by engineerFABRICATION PROCESS: weldedFASTENER: Per engineer's specifications2p, tyB56"1'-2"6. SIGN FASTENERSPer engineer's specifications"CLR11/25. POST CAPMATERIAL: 1/8" thick aluminumFabricated alumimum sheet top, fully weldedand fabricated sides with all edges and cornersneatly finishedFASTENER: mechanically fasten to wood post615'-6" post height#2'14'-10"YCIT GOLONorthwestern IndianaRegional Planning Commission2'-10"1 1/2" min.3CLIENTNIRPC Unified Trail Wayfinding8"PROJECTB408 August 20163/8" Ø hole, typ of 2DOCUMENT ISSUEPedestrian Regulatory SignSHEET TITLE1Sign LayoutScale: 1 1/2" 1'-0"2Front ElevationScale: 3/4" 1'-0"3Side Elevation8Scale: 3/4" 1'-0"SHEET NUMBER
KEY NOTESCL1. ALUMINUM SLEEVE & FRAMEMATERIAL: 1/8" thick aluminumFabricated alumimum sheet sign face andback, fully welded and fabricated sides with alledges and corners neatly finishedFRAME: Fabricated aluminum channel internalstructure to engineer's specification. Frame tobe set inside perimeter of sign sleeve43 1/2"7"·These drawings are intended to illustratedesign intent only and are not forconstruction. All final engineering andconditions of the project are theresponsibility of the fabricator. Shopdrawings by the fabricator must besubmitted for approval, prior to proceedingwith fabrication.·The quality of fit and finish on the finalproduct must meet or exceed therequirements of these design intentdocuments. Any variations to design,materials, or fabrication methods must beapproved by the Owner or Representive.·Welds: All welds shall be ground smooth,paint all seams.·Hardware: All exposed hardware shall betamper proof fasteners.·All exposed edges painted to matchadjacent face.·Colors shown are for reference only andare subject to the limitations of the printingprocess. Refer to referenced color systemscontained within these drawings for actualspecifications.·Scaled examples shown are for referenceonly, and do not necessarily reflect actualsite conditions. Detailed site surveys arerequired prior to fabrication and installation.·Messages shown in these drawings are forgeneral reference only. Refer to messageschedules for actual required messages.3. CONCRETE FOOTINGConcrete footing to engineer's specifications.Conceal hold down bolts within sign structure54. CUT-OUT TEXTText and numbers cut out of aluminum sleeve.EDGES: Routed, finished smooth5. BACK PANELMATERIAL: 1/8" thick aluminumFASTENER: welded to sleeve3GENERAL NOTES2. DIGITAL PRINTDigitally printed 'Praire Grass' silhouette andstone texture (not shown)Type: Highway Gothic,2" highWng i seD gn i nna l P a t l A800 S Broadway,Baltimore, MD 21231ph: 443.218.8165DetailScale: 1 1/2" 1'-0"10"8"3-Northwestern IndianaRegional Planning Commission2'-6"1CLIENTSNIRPC Unified Trail Wayfinding2PROJECT308 August 20164"2'-10"Sign is double-sidedDOCUMENT ISSUEMile Marker PostSHEET TITLE1Front ElevationScale: 3/4" 1'-0"2Side Elevation9Scale: 3/4" 1'-0"SHEET NUMBER
KEY NOTES1. GREENWAYS & BLUEWAYS LOGOMATERIAL: 1/4" thick aluminumFABRICATION PROCESS: router cutEDGES: routed, finished smoothFASTENER: per engineer's specificationsGRAPHICS/TEXT: digitally printedManufacturer to field verify allwall conditions and specifythe appropriate mechanicalfastener3"6"Street Name1'Mechanical wallfasteners to bespecified by installer343/8" Ø hole, typ of 6Front ViewSide ViewTrail Underpass Sign3GENERAL NOTES·These drawings are intended to illustratedesign intent only and are not forconstruction. All final engineering andconditions of the project are theresponsibility of the fabricator. Shopdrawings by the fabricator must besubmitted for approval, prior to proceedingwith fabrication.·The quality of fit and finish on the finalproduct must meet or exceed therequirements of these design intentdocuments. Any variations to design,materials, or fabrication methods must beapproved by the Owner or Representive.·Welds: All welds shall be ground smooth,paint all seams.·Hardware: All exposed hardware shall betamper proof fasteners.·All exposed edges painted to matchadjacent face.·Colors shown are for reference only andare subject to the limitations of the printingprocess. Refer to referenced color systemscontained within these drawings for actualspecifications.·Scaled examples shown are for referenceonly, and do not necessarily reflect actualsite conditions. Detailed site surveys arerequired prior to fabrication and installation.·Messages shown in these drawings are forgeneral reference only. Refer to messageschedules for actual required messages.2. PAVEMENT MARKINGMATERIAL: Preformed thermoplastic3. UNDERPASS SIGNFinal size of sign dependant on sign placementand at the discretion of the engineer to ensurelegibility for trail users.MATERIAL: 41" thick aluminumFABRICATION PROCESS: router cutEDGES: routed, finished smoothFASTENER: per engineer's specificationsGRAPHICS/TEXT: digitally printed4. DIGITAL PRINTDigitally printed 'Prairie Grass' silhouette andstone texture (not shown)Scale: 1 1/2" 1'-0"1'21'-6 3/4"1" White Border8"13/4"Northwestern IndianaRegional Planning CommissionCLIENT1"8"2"3'ng i seD gn i nna l P a t l A800 S Broadway,Baltimore, MD 21231ph: 443.218.8165Mile2NIRPC Unified Trail WayfindingType: Highway Gothic Wide,2" highPROJECT08 August 2016DOCUMENT ISSUE8"3/8" Ø hole, typ of 2Mile Marker PostSHEET TITLE1Sign BlazeScale: 1 1/2" 1'-0"2Pavement MarkingScale: 1 1/2" 1'-0"10SHEET NUMBER
August 2016 The purpose of these drawings is to illustrate design intent. Drawings are not for construction. Written dimensions on these drawings have precedence over scaled dimensions. The further development and engineering of these drawings shall be submitted as shop drawings to the Project
