WIXLIB

SN29402177B TX-RZ810 BAS En 1702xx.book Before start9 ページ２０１７年２月９日 Hookup木曜日午後３時３３分 Setup Playback Part NamesStep2: Connect the Speakersin case of:Pages 3 to 7Connect 123456 for a 5.1-channel system. With a7.1-Channel System (with Surround Back Speakers), alsoconnect 7 and 8. With a 7.1-Channel System (withHeight Speakers), connect 9:. Up to two poweredsubwoofers can be connected. The same signal is outputfrom each of the SUBWOOFER jacks.0 You can also connect both 78 and 9:. However,you can only output audio from one set of 78 or 9:at a time. When you have connected both, you canselect which speakers to prioritize with "SpeakerLayout" (ÄP26) in the Quick Menu.Setup0 Settings for the speaker configuration you haveconnected need to be made in "1. AccuEQ RoomCalibration" (ÄP20) in Initial Setup. Note that if youare using height speakers, set "Speaker Channels"to "5.1.2 ch" in the setting screen. Select "7.1.2 ch"if you have connected both surround backspeakers and height speakers.0 (North American models) If any of the speakershave 4 Ω or more to less than 6 Ω impedance,change "2. Speaker" - "Configuration" - "SpeakerImpedance" in the Setup menu to "4ohms".1/2 (12 mm)12Make sure the exposed wires of the speakers do not stick out ofthe speaker terminals when connecting. If the exposed wires ofthe speakers touch the rear panel or the and – wires touch eachother, the protection circuit will be activated.1 Speaker cable, 2 Subwoofer cable9

SN29402177B TX-RZ810 BAS En 1702xx.book Before start10 ページ２０１７年２月９日 Hookup木曜日 Setup午後３時３３分 Playback Part Namesin case of:Page 8Connect front speakers compatible with Bi-Ampingconnection to the FRONT jacks and the HEIGHT jacks.Make sure you remove the jumper bar fitted between thewoofer jacks and tweeter jacks of the front speakers. Incase of Bi-Amping connection, refer to the instructionmanual of your speakers. Up to two powered subwooferscan be connected. The same signal is output from each ofthe SUBWOOFER jacks.Setup0 Bi-Amping connection requires you to changesome settings. Select "Yes" in "Bi-Amp" in "1.AccuEQ Room Calibration" (ÄP20) in the InitialSetup.0 (North American models) If any of the speakershave 4 Ω or more to less than 6 Ω impedance,change "2. Speaker" - "Configuration" - "SpeakerImpedance" in the Setup menu to "4ohms".1/2 (12 mm)1For highfrequencyFor lowfrequency101 Speaker cable, 2 Subwoofer cable2Make sure the exposed wires of the speakers do not stick out ofthe speaker terminals when connecting. If the exposed wires ofthe speakers touch the rear panel or the and – wires touch eachother, the protection circuit will be activated.

SN29402177B TX-RZ810 BAS En 1702xx.book Before start11 ページ２０１７年２月９日 Hookup木曜日午後３時３３分 Setup Playback Part NamesStep3: Connect the TVif you have:ARC TVThis unit is connected between your TV and AVcomponents. If you connect two or more AV components,you can select the video displayed on the TV and theaudio output from this unit by changing the input selector.Shown here are the connections for a TV that supportsthe ARC (Audio Return Channel) feature. By connectingwith a single HDMI cable, you can not only output thevideo input to this unit to the TV, but you can also play thesound from the TV through this unit.Choose an HDMI IN jack on the TV that supports ARCwhen connecting.Setup0 Settings are required to use the ARC function.Select "Yes" in "5. Audio Return Channel" (ÄP21)in the Initial Setup.0 Please refer to the TV's operation manual fordirections on connections and setup for the TV.HDMI IN (ARC)1Another TV or projector can be connected to the HDMI OUT SUBjack. This jack does not support ARC. For details about how tooutput video from the HDMI OUT SUB jack (ÄP22)TV1 HDMI cable11

SN29402177B TX-RZ810 BAS En 1702xx.book Before start12 ページ２０１７年２月９日 Hookup木曜日 Setup午後３時３３分 Playback Part Namesif you have:Non-ARC TVThis unit is connected between your TV and AVcomponents. If you connect two or more AV components,you can select the video displayed on the TV and theaudio output from this unit by changing the input selector.This describes the connections for a TV that does notsupport the ARC (Audio Return Channel) feature. Byconnecting with both an HDMI cable and a digital opticalcable, you can not only output the video input to this unitto the TV, but you can also play the sound from the TVthrough this unit.If the TV doesn't have a DIGITAL OPTICAL OUT jack, usean analog audio cable and connect the TV's ANALOGAUDIO OUT jack to the AUDIO IN TV jack on this unit.0 Connection with a digital optical cable is not necessaryif you will watch TV through a device such as a cableset-top box (that is, not use a tuner built into the TV)that you have connected to the INPUT jack on this unit.2TV121 HDMI cable, 2 Digital optical cable1Another TV or projector can be connected to the HDMI OUT SUBjack. This jack does not support ARC. For details about how tooutput video from the HDMI OUT SUB jack (ÄP22)

SN29402177B TX-RZ810 BAS En 1702xx.book Before start13 ページ２０１７年２月９日 Hookup木曜日午後３時３３分 Setup Playback Part NamesStep4: Connect the AV Componentsif you have:HDMI AV ComponentsThis is an example of connection with an AV componentthat has an HDMI jack. With connection to an AVcomponent that conforms with the CEC (ConsumerElectronics Control) standard, you can use features suchas the HDMI CEC feature that links with the input selector,and the HDMI Standby Through feature which allows youto play video and audio from AV components on the TVeven when this unit is in standby mode.0 To play 4K or 1080p video, use a high speed HDMIcable. Further, to enjoy HDCP2.2 compatible video,connect to the HDMI IN1 to IN3 jacks.Setup0 HDMI setup (ÄP21) is required to use the HDMICEC and HDMI Standby Through features. Makesettings after all connections are complete.0 To enjoy digital surround sound including DolbyDigital, audio output should be set to "Bitstreamoutput" on the connected Blu-ray Disc player orother device.1You can connect a device such as a video camera to the AUXINPUT HDMI jack on the front panel.BD/DVDCable/Satellite set-topbox1 HDMI cableStreaming mediaplayerGAME13

SN29402177B TX-RZ810 BAS En 1702xx.book Before start14 ページ２０１７年２月９日 Hookup木曜日午後３時３３分 Setup Playback Part Namesif you have:Non-HDMI AV Components2ORBD/DVD141 Component video cable, 2 Digital coaxial cable, 3 Analog audio cable31This is an example of connection with an AV componentthat does not have an HDMI jack. Make the connectionsto the AV component to match the jacks it has. Whenvideo input connection is to the BD/DVD jack, the audioinput connection should also be to the BD/DVD jacks, andso on, so that you connect the video input jacks to thejacks with the same name as the audio input jacks. Notethat video signals input to the VIDEO IN jack or theCOMPONENT VIDEO IN jacks will be converted to HDMIvideo signals and then output from the HDMI OUT jack.0 To enjoy digital surround playback in formats such asDolby Digital, you need to make a connection for audiosignals with a digital coaxial cable or digital opticalcable.0 It is possible to change assignment of the input jacksyou see in the illustration at left, so you can alsoconnect to any jack other than BD/DVD. For details,see the Advanced Manual.Setup0 The COMPONENT VIDEO IN jacks arecompatible only with 480i or 576i resolution. Whenyou input video signals to the COMPONENTVIDEO IN jacks, set the output resolution of theplayer to 480i or 576i. Select interlace if there is nooption for 480i, etc. If your player does not support480i or 576i output, use the VIDEO IN jack.0 To enjoy digital surround sound including DolbyDigital, audio output should be set to "Bitstreamoutput" on the connected Blu-ray Disc Player orother device.

SN29402177B TX-RZ810 BAS En 1702xx.book Before start15 ページ２０１７年２月９日 Hookup木曜日 Setup午後３時３３分 Playback Part Namesif you have:Audio ComponentsExample of a connection with an audio component.Connect a CD player using a digital optical cable oranalog audio cable. You can also connect a turntable thathas an MM-type cartridge to the PHONO jack.0 If the turntable has a built-in audio equalizer, connect itto an AUDIO IN jack other than the PHONO jack.Further, if the turntable uses an MC type cartridge,install an audio equalizer compatible with the MC typecartridge between the unit and the turntable, thenconnect to any AUDIO IN jack other than the PHONOjack.If the turntable has a ground wire, connect it to the GND terminalof this unit.OR12Turntable1 Digital optical cable, 2 Analog audio cableCD15

SN29402177B TX-RZ810 BAS En 1702xx.book Before start16 ページ２０１７年２月９日 Hookup木曜日 Setup午後３時３３分 Playback Part NamesStep5: Multi-zone Connectionif you connect:ZONE 2 TVMAIN ROOMZONE21TV161 HDMI cableYou can enjoy content from a Blu-ray Disc player on a TVequipped with an HDMI input jack in the separate room(ZONE 2) by playing a Blu-ray Disc player in the mainroom (where this unit is located), or play the content fromanother AV component. Only the video from devicesconnected to the HDMI IN1 to IN3 jacks can be played onthe TV in the separate room.Setup0 Settings are required in Initial Setup, "4. MultiZone Setup" (ÄP21) to enjoy this feature.0 The audio from externally connected AVcomponents can only be output when the audio isanalog or 2ch PCM audio signals. It may also benecessary to convert the audio output of the AVcomponent to PCM output.

SN29402177B TX-RZ810 BAS En 1702xx.book Before start17 ページ２０１７年２月９日 Hookup木曜日 Setup午後３時３３分 Playback Part Namesif you connect:ZONE 2/3 PRE/LINE OUTYou can enjoy 2ch audio in the separate room throughspeakers connected to a pre-main amplifier or poweramplifier by, for example, playing a Blu-ray Disc player inthe main room (where this unit is located) and listening tointernet radio in the separate room (ZONE 2/ZONE 3).ZONE 2Connect with HDMI IN 1 to 3 if you want to output anexternal AV component to ZONE 2. If the AV componentdoesn't have an HDMI jack, connect using a digital opticalcable, digital coaxial cable, or analog audio cable. If anyof these are already used, you do not have to connectusing any of the others.MAIN ROOMZONE2LINEIN1Necessary for ZONE 3LINEINZONE 3To output the audio of an external AV component to ZONE3, connect using an analog audio cable. Output to ZONE3 is not possible when you connect with an HDMI cable ordigital optical/coaxial cable.Setup0 Settings are required in Initial Setup, "4. MultiZone Setup" (ÄP21) to enjoy this feature.0 The audio from externally connected AVcomponents can only be output when the audio isanalog or 2ch PCM audio signals. If you haveconnected to this unit with an HDMI cable or digitaloptical/coaxial cable, may be necessary to convertthe audio output of the AV component to PCMoutput.BD/DVDZONE31 Analog audio cable17

SN29402177B TX-RZ810 BAS En 1702xx.book Before start18 ページ２０１７年２月９日 Hookup木曜日 Setup午後３時３３分 Playback Part Namesif you connect:ZONE 2 SPEAKER(ZONE 2A for NorthAmerican models)You can enjoy 2ch audio in the separate room by, for example,playing a Blu-ray Disc player in the main room (where this unitis located) and listening to internet radio through the speakersin the separate room (ZONE 2). This feature is not available ifyou have connected the front speakers using Bi-Ampingconnection. You can play through a maximum of 5.1 channelsin the main room during ZONE 2 playback. Listening modessuch as Dolby Atmos cannot be selected.MAIN ROOM1ZONE 2(ZONE 2A for NorthAmerican models)ZONE 2B(North American models)181 Speaker cableZONE 2 (ZONE 2A for North American models)Connect with HDMI IN 1 to 3 if you want to output anexternal AV component to ZONE 2. If the AV componentdoesn't have an HDMI jack, connect using a digital opticalcable, digital coaxial cable, or analog audio cable. If anyof these are already used, you do not have to connectusing any of the others.(North American models) ZONE 2BYou can output the same audio as described in ZONE 2Awith another set of speakers to output as ZONE 2B. In thiscase, connect speakers with 8 Ω to 16 Ω impedance forZONE 2 A/B. These cannot be connected when heightspeakers are connected.Setup0 Settings are required in Initial Setup, "4. MultiZone Setup" (ÄP21) to enjoy this feature.0 To use the ZONE 2A B output, set "ZoneSpeaker" in "1. AccuEQ Room Calibration" in InitialSetup to "Zone 2 A B" (ÄP20).0 The audio from externally connected AVcomponents can only be output when the audio isanalog or 2ch PCM audio signals. If you haveconnected to this unit with an HDMI cable or digitaloptical/coaxial cable, may be necessary to convertthe audio output of the AV component to PCMoutput.

SN29402177B TX-RZ810 BAS En 1702xx.book Before start19 ページ２０１７年２月９日 Hookup木曜日 Setup午後３時３３分 Playback Part NamesStep6: Connect Other CablesAMAntenna HookupNetwork HookupMove the antenna around while playing the radio to findthe position with the best reception. Use a thumb tack orsimilar to attach the indoor FM antenna to a wall.Connect this unit to the network using wired LAN or Wi-Fi(wireless LAN). You can enjoy network features such asinternet radio, Music Server, and AirPlay by connecting theunit to the network.If you connect by wired LAN, connect with an Ethernetcable to the ETHERNET port as shown in the illustration.To connect by Wi-Fi, then after selecting "Wireless" in "3.Network Connection" (ÄP21) in Initial Setup, select thedesired setting method and follow the onscreeninstructions to configure the connection.FMAM loop antennaIndoor FM antenna(North American models)Power Cord Hookup(European, Australian and Asian models)This unit includes a removable power cord. Connect thepower cord to the power outlet after completing all otherconnections. Connect the power cord to AC INLET of theunit and then connect to the outlet. Always disconnect theoutlet side first when disconnecting the power cord.19

SN29402177B TX-RZ810 BAS En 1702xx.book Before start20 ページ２０１７年２月９日 Hookup木曜日 Setup午後３時３３分 Playback Part NamesStep7: Power On & Initial SetupInitial Setup starts automaticallyOnce all connections are complete, change the TV's inputto the input for this unit, inset batteries in the remotecontroller, and press Í to turn the power on. When youturn the unit on for the first time, Initial Setup isautomatically shown on the TV to enable you to makesettings required for startup using simple operationsfollowing onscreen guidance.These instructions will guide you through some items thatyou need to check beforehand. Read beforehand so thesetup goes smoothly.1. AccuEQ Room CalibrationPlace the supplied speaker setup microphone in thelistening position, measure the test tones emitted by thespeakers, then the unit automatically sets the optimumvolume level for each speaker, the crossover frequencies,and the distance from the listening position. This alsoenables correction of distortion caused by the acousticenvironment of the room.Initial SetupLanguage landsSETUP MICSvenskaExitabOperationSelect the item with the cursors of the remote controllerand press ENTER (a). To return to the previous screen,press(b).To redo the Initial SetupIf you terminate the procedure on the way or want tochange a setting made during Initial Setup, pressonthe remote controller, select "7. Miscellaneous" – "InitialSetup", and press ENTER.200 When putting the speaker setup microphone on a tripod,refer to the illustration when putting it in place.0 The subwoofer sound may not be detected since it isextremely low frequencies. Set the subwoofer volume tomore than halfway.0 Calibration takes several minutes to be completed. Thespeakers emit the test tone at high volume duringmeasurement, so be careful of your surroundings. Keepthe room as quiet as possible during measurement. Ifthe measurement is interrupted, turn off the householdappliances.0 When using THX certified speakers, THX recommendssetting the crossover frequency to "80Hz(THX)". It isalso recommended to manually adjust the settings foreach speaker to suit the specific characteristics of eachroom.

SN29402177B TX-RZ810 BAS En 1702xx.book Before start21 ページ２０１７年２月９日 Hookup木曜日 Setup午後３時３３分 Playback Part NamesHDMI Setup2. Source ConnectionCheck that each input source is connected correctly. Followthe guidance, select the input you want to confirm, startplay of the selected player, and confirm that the imagesappear on the TV and that sound is played.3. Network ConnectionSet up Wi-Fi connection with an access point such as awireless LAN router. There are the following two methods ofconnecting by Wi-Fi:"Scan Networks": Search for an access point from thisunit. Find out the SSID of the access point beforehand."Use iOS Device (iOS7 or later)": Share the iOS device'sWi-Fi settings with this unit.If you select "Scan Networks", there are a further twochoices of connection method. Check the following.0 "Enter Password": Enter the password (or key) of theaccess point to connect.0 "Push Button": If the access point has an automaticconnection button, you can connect without entering apassword.0 If the SSID of the access point is not displayed, then inthe screen listing the SSIDs, select "Other." with the Xcursor on the remote controller and press ENTER, thenfollow the onscreen instructions.Keyboard inputWi-Fi SetupSSIDabcdefghijklmnopqrstuvwxyz1234567890- \,./;:@[]A/aƟOKơTo switch between upper and lower case, select "A/a" onthe screen and press ENTER. To select whether to maskthe password with " ＊ " or display it in plain text, pressMEMORY on the remote controller. Press CLEAR to deleteall the input characters.0 A confirmation screen asking you to agree to the privacypolicy is displayed during network setting. Select "Yes"and press ENTER to indicate agreement.4. Multi Zone SetupHDMI CECMake this setting to enable the control feature for devicescomplying with the CEC standard. This is set to onautomatically if you have selected "Yes" in "5. Audio ReturnChannel" in the Initial Setup.Press thebutton on the remo

For 5.1-Channel System This is a 5.1-channel system that is the basic surround system. Front speakers output front stereo sound and a center speaker outputs center sound such as dialogs and vocals. Surround speakers create back sound field. Powered subwoofer reproduces bass sounds and creates rich sound field. The front speakers should be .