TANNING BED INSTRUCTION MANUAL

Transcription

16R / 24S / 24SR24R / 32S / 32RTANNING BEDINSTRUCTIONMANUAL

16R / 24S / 24SR24R / 32S / 32RDangerUltraviolet radiation. Follow instructions. Avoid Overexposure. As withnatural sunlight, overexposure can cause eye and skin injury and allergic reactions. Repeatedexposure may cause premature aging of the skin and skin cancer. WEAR PROTECTIVE EYEWEAR;FAILURE TO MAY RESULT IN SEVERE BURNS OR LONG TERM INJURY TO THE EYES. Medicationsor cosmetics may increase your sensitivity to the ultraviolet radiation. Consult physician beforeusing sunlamp if you are using medications or have a history of skin problems or believe yourselfespecially sensitive to sunlight. If you do not tan in the sun, you are unlikely to tan from the useof this product. Children, the elderly, or fair skinned people who always burn easily and eithernever tan or tan minimally should not use this equipment.To use, lie down under canopy and pull down as far as adjustment will allow. Do not use withoutclear plastic panel and wire grill in place. Untanned persons should not tan on consecutive daysduring their first week of tanning. Never tan more than once a day. Tanning normally appearsafter the first few sessions and maximizes after approximately four weeks. Tan once or twice perweek thereafter to maintain appearance. Persons already having a base tan may begin atadvanced levels corresponding to the extent of their base tan.Skin CHEDULEI Sensitive SkinII Light SkinIII Normal SkinIV Dark SkinIIIIIIIVIIIIIIIV(Burns easily and severely and does not tan.)(Burns easily and severely and tans minimally.)(Burns moderately and tans average.)(Burns minimally, tans easily and above average.)SKIN TYPEMAXIMUM EXPOSURE TIME IN MINUTES – 15 MINUTE MODELSWeek 1Week 2Week 3Week 4Sensitive Skin: Burns easily & severelyDoes not tanLight Skin: Burns easily & severelyTans minimallyNormal Skin: Burns moderatelyTans moderatelyDark Skin: Burns minimallyTans well/above averageTanning Not Advised468106810138101215SKIN TYPEMAXIMUM EXPOSURE TIME IN MINUTES – 20 MINUTE MODELSWeek 1Week 2Week 3Week 4Sensitive Skin: Burns easily & severelyDoes not tanLight Skin: Burns easily & severelyTans minimallyNormal Skin: Burns moderatelyTans moderatelyDark Skin: Burns minimallyTans well/above averageTanning Not Advised468126810158101520New lamps emit approximately 10% more ultraviolet radiation during the first 50 hours of operation.Recommended tanning times should therefore be reduced by approximately 10% during that period.WARNING:Read these instructions before using this sunlamp product. All persons in theroom should wear protective eyewear when lamps are on. Recommended eyewear: Providedeyeshields or equivalent eyewear as defined under 21 CFR 1040.20. Other types of eyewear maynot provide adequate protection. Failure to use protective eyewear may result in severe burns orother eye injury. If discomfort develpos, discontinue use and consult a physician.

The following lamps have been certified for use in the Solar Storm16R, 24S, 24SR, 24R, 32S or 32R models:2645 Inferno Wolff lamps (15 minute)2393 CC 5.0 Wolff lamps (20 minute)120V/240V Outlets1704 FT LSI lamps (20 minute)1705 BT LSI lamps (20 minute)NEMA 6-20(220V)Electrical RequirementsYour sunbed operates from a 120V or 220V AC source. For 120V models, you should have a standardelectrical outlet on a dedicated 20 Amp Circuit Breaker. For 220V models, you should have a NEMA 6-20RElectrical outlet on a dedicated 20 Amp Circuit Breaker installed in the room in which you will use the unit.For SS32R models, 30 Amp service will need to be hard-wired to the bed. We recommend installationby a professional electrician. The outlet must be earth grounded.Standard 120V! DANGERShock hazard.Disconnect power before servicingor removing any protective covers.Do not operate this device nearwater or while you are wet.! DANGERSome medications may increase yoursensitivity to ultraviolet light. It isrecommended that you consult a physicianbefore using this sunbed if taking anymedication or if you suspect that your skinmight be especially sensitive to sunlight.! WARNINGWear protective eyewear. Failure to may result in severe burns or long term injury to the eyes.! CAUTIONAir from the room is used to cool the sunbed. Maximum ambient room temperature should be80oF. Place your sunbed no closer than 6" from any wall. Make sure nothing obstructs theairflow into the sunbed's endcaps or out of the fan openings. A poorly ventilated room maycause the unit to become hot and cause discomfort to the user.Unpacking and InspectionYour sunbed comes in two cardboard cartons. Pull back the plastic sheet and, with a helper, graspthe bench and pull it from the carton bottom, leaving the plastic wrap and the carton packaging.Do not try to lift the unit with the plastic still on as it may slip. Do the same with the canopy.The canopy box contains the canopy and a pair of gas springs. The bench box contains the bench,assembly hardware and stand legs. Inspect the items and make sure they are free from any visibledamage. Report the extent of any damage to the transportation company.Hardware InventoryAllen-head Bolt 5/16 X 1”Quantity 6Hinge Brackets(1) Left, (1) Right5/16” Metal WasherQuantity 10Allen-head Bolt 5/16 X 1.5”Quantity 4Hex (Allen) WrenchQuantity 1Safety GogglesQuantity 1

Assembly Procedures1 Lay the bench upside down on the floor. Locate the two stand legs.six 5/16” X 1” bolts and six 5/16” washers, fasten the2 Usinglegs to the bench as shown, with the two small skirtmounting holes toward the back, by installing thecenter bolt first. You may have to gently push the sidesof the legs in to align holes. Tighten with the allenwrench.bench over. Install hinge3 Turnbrackets to ends of bench.Secure using 5/16” X 1.5” Allenhead bolts and 5/16” metalwashers. Tighten bolt snug,then an additional half turn.Long Boltthe canopy and hold it4 Liftbetween the hinge brackets.5/16” X 1.5” bolts5 Insertwith 5/16” washers into bothhinge brackets. Tighten boltsinto the endcap threaded insertsuntil snug, then an additionalhalf turn. Do not overtightento avoid damaging threadedinserts.gas springs have6 Thea locking mechanism.Pry back thelocking clipwith a flatscrewdriver.a helper holding the canopy open, align ends of gas spring ball joints7 Withwith pivot studs and push into place. Be sure rod end is down as shown.DO NOT lower canopy until bothgas springs are engaged!Lift and lower the canopy a few times to lubricategas springs for optimum performance.8the three-prong power cord into the proper9 Plugdedicated outlet. 32R models are to be hard-wired.(*See Electrical Requirements.)! CAUTIONFailure to engage locking clips mayresult in the ball joints working loose,allowing the canopy to fall, which mayresult in damage to the unit and injury.! CAUTIONVoltage for 120V beds mustbe between105-125 VAC.Voltage for 220V beds mustbe between215-230 VAC orwill void warranty.

Using Your SunbedBefore using your sunbed, please note the following: Your skin should be free of cosmetics, tanning oils, or other body lotions prior to tanningexcept for those specifically made for use with tanning devices. However, do not removenatural body oils by bathing or showering immediately before tanning. Keep treated hair from contacting sunbed surfaces. Many hair products can damage thesunbed acrylic. Wear a shower cap or towel if you use gels, mousses, sprays or other hairproducts. Your sunbed is designed for individual use. Always wear the safety goggles supplied withyour sunbed or another approved pair of goggles, as defined under 21 CFR 1040.20.Regular sunglasses do not provide adequate protection from ultraviolet light.Exposure TimesFollow the guidelines for skin type and exposure times according to your model as shown in thetables below. Untanned persons should not tan on consecutive days during their first week oftanning. Never tan more than once a day. Tanning normally appears after the first few sessionsand maximizes after approximately four weeks. Tan once or twice per week thereafter to maintainapearance. Persons already having a base tan may begin at advanced levels corresponding to theextent of their base tan.Skin CHEDULEI Sensitive SkinII Light SkinIII Normal SkinIV Dark Skin(Burns easily and severely and does not tan.)(Burns easily and severely and tans minimally.)(Burns moderately and tans average.)(Burns minimally, tans easily and above average.)IIIIIIIVIIIIIIIVSKIN TYPEMAXIMUM EXPOSURE TIME IN MINUTES – 15 MINUTE MODELSWeek 1Week 2Week 3Week 4Sensitive Skin: Burns easily & severelyDoes not tanLight Skin: Burns easily & severelyTans minimallyNormal Skin: Burns moderatelyTans moderatelyDark Skin: Burns minimallyTans well/above averageTanning Not Advised468106810138101215SKIN TYPEMAXIMUM EXPOSURE TIME IN MINUTES – 20 MINUTE MODELSWeek 1Week 2Week 3Week 4Sensitive Skin: Burns easily & severelyDoes not tanLight Skin: Burns easily & severelyTans minimallyNormal Skin: Burns moderatelyTans moderatelyDark Skin: Burns minimallyTans well/above averageTanning Not Advised468126810158101520Timer OverviewThe LT1 Timer is ideal for controlling residential tanning beds.SpecificationsDepth Width Height Current Draw Relay Spec. Configuration120VAC@5A SPST Form A1.408" 4.10" 2.1"40mA

WiringConnect the LT1 to the tanning bed using the white header connector on the back of the circuit board.See the diagram.Removal of Acrylic110V220V110VTo start a session, press the Set button on the LT1. Thetime will go to the maximum time then count down.The lamps will turn on automatically. You can decreasethe time by pressing the Set button. To cancel a session,press the Start/Stop button on the LT1. The display willgo to a 0.JP2JP1Session ControlPin 3 - Neutral or L2Pin 2 - AC HOT or L1Pin 1 - OutputRemove black acrylic locking strips first. To remove the acrylic locking strip, insert a flat head screwdriverinto the front edge of the locking strip and pry up. After Acrylic locking strip is removed, go to the headof the bed. Place the flat head screwdriver between the acrylic and aluminum extrusion. You will then liftthe acrylic up enough to get your hand under it. Please use a glove due to the acrylic is very sharp and willcut an unprotected hand. With your hand placed between the acrylic and extrusion, lift up on the acrylicuntil it pops out of the extrusion. Lift the acrylic out of the bed.Replacing AcrylicInsert Acrylic into aluminum extrusion lip in back of bed. Apply pressure to back aluminum extrusion whilepushing acrylic down into the bed until it pops into the front aluminum extrusion. Replace black acryliclocking strips.Care and MaintenanceCleaning After UseClean and disinfect your tanning bed’s bench and canopy after each use. Use a non-abrasive disinfectantcleaner that does not contain ammonia or ammonia derivitaves. Ammonia may damage the acrylicshield. Spray the acrylic lightly with disinfectant and wipe dry with a clean soft cloth. Wipe the canopy grillwith a soft cloth slightly dampened with disinfectant, then wipe dry.Thorough Periodic CleaningThe cooling fans draw air through the bed and will cause a dust buildup on the lamps and reflectors.When a dust buildup is observed, it is necessary to thoroughly clean the inside of the bench and canopy.1)2)3)4)5)Remove the acrylic shield, metal grill and lamps.With a soft cloth, wipe the entire length of each lamp.Clean both sides of the acrylic shield and grill with a non-ammonia disinfectant cleaner.Wipe the reflectors with a clean damp cloth.Re-install the lamps, acrylic shield and grill.Mechanical Inspection Inspect the unit’s fasteners verifying that all are firmly in place. Pay particular attention to the hinge bolts. Inspect gas springs for signs of wear. Replace gas springs that will not hold the canopy in the fully openposition when raised. Inspect the AC power cord and its connections. Inspect the acrylic. Replace if broken, cracked or badly scratched.

Solar Storm Lamp ConfigurationUse this table to determine the correct lamp type, quantity and placement for your Solar Storm model:SS16R DualSS16R PWSS16R BronzeSS16RSS24S DualSS24S PWSS24S BronzeSS24SSS24SRSS24R DualSS24R PWSS24R BronzeSS24RSS32S DualSS32S PWSS32S BronzeSS32SSS32R32R BronzeSS32R PWSS32R DualCanopyBenchMax. ExposureQuantityLampQuantityLampTime (Minutes)417042082393 CC4170541704PW2082393 CC42393 CC82645 Inferno82645 Inferno1582393 CC82393 CC20617042393 CC20126170561704PW20122393 CC62393 CC122645 Inferno122645 Inferno15122393 CC122393 CC20122645 Inferno15122645 Inferno62281 Renew T561704122393 CC206170561704PW202393 CC1262393 CC122645 Inferno122645 Inferno15122393 CC122393 CC208170420162393 CC8170581704PW20162393 CC82393 CC162645 Inferno162645 Inferno15162393 CC162393 CC20162393 CC162393 CC20162645 Inferno162645 Inferno1581704PW162393 CC2082393 CC81704162393 CC2081705

Solar Storm16R / 24S / 24SR / 24R / 32S / 32RManufactured by,1044 Fordtown Road - Kingsport, TN 37663423-349-2900Form# F-922-001

Voltage for 120V beds must be between105-125 VAC. Voltage for 220V beds must be between215-230 VAC or will void warranty.! CAUTION Failure to engage locking clips may result in the ball joints working loose, allowing the canopy to