WIXLIB

TECHNICAL DATA SHEET:WEDGE ANCHORZINC, GALVANIZED & STAINLESS STEELThe Allfasteners Wedge Anchor is a torque-controlled, wedge expansion anchor for heavy dutyfastening applications where high pull out values in concrete are needed. The anchor and the holediameter are the same, simplifying the anchor installation by placing the anchor through the existinghole in the material to be fastened. Used in fastening sheet metal, steel and aluminum angles, orwood to concrete. Due to its high resistance to vibratory loads, this anchor is ideal for installingmachinery, hand rails, dock bumpers, storage racks, etc.APPLICATIONS & USES§§ Solid Concrete (Normal-Weight and Light-Weight)§§ Grout-Filled Concrete Block§§ Concrete-Filled Metal Deck§§ Structural Anchorage§§ Machinery, Hand rail, dock bumper installation§§ Storage racking anchorageKEY FEATURES§§ Length ID stamped on visible end of each anchor§§ Fully threaded for use in all applications, including varied material thickness.Eliminates subsurface obstruction problems.§§ Nominal drill diameter is the same as anchor diameter, allowing anchor to beinstalled after setting of fixture§§ Heavy duty applications§§ Depth of holes can be over-drilled with no loss of load capacity§§ Impact section is raised (dog-point) to prevent thread damage duringinstallation§§ Mechanical expansion action allows immediate load applicationMATERIAL SPECIFICATIONSCOMPONENTSZINCHOT DIPPED GALVANIZEDC1010 Carbon SteelBodyC1010 Carbon SteelExpanding ClipCarbon SteelType 304 StainlessHex NutASTM A563 Grade A Carbon SteelASTM A563 Grade A Carbon SteelFlat WasherCarbon SteelCarbon SteelPlating/FinishElectroplated zinc plating (clear)Hot Dipped Galvanizedwww.allfasteners.com Customer Service 800 577 3171Doc: WedgeAnchorTDS Version Date: 04/22/19 Page 1 of 10

TECHNICAL DATA SHEET:WEDGE ANCHORZINC, GALVANIZED & STAINLESS STEELMATERIAL SPECIFICATIONS (CONT'D)Components304 STAINLESS316 STAINLESSType 304 Stainless SteelType 316 Stainless SteelBodyExpanding ClipHex NutFlat WasherPlating/FinishDescriptionA four piece assembly consisting of (1) anchor bolt threaded at one end with a unified pitch, a shoulder at the opposite endwhich retains a free-spinning clip, (2) a clip with three lateral slits and projections designed to exert greater holding powerthe greater the load that is applied, (3) a hex nut, and (4) a flat washer.Applications/AdvantagesThese are heavy-duty, non-bottom bearing anchors of greater shear strength than other light and medium-duty expansionanchors. The design of the expansion clip assures full contact with the masonry. Wedge anchors withstand temperaturefluctuations well. For best performance, minimum anchor spacing should be 10 hole diameters and minimum edgedistance be 5 hole diameters.CARBON STEELANCHOR BODYMaterialEXPANSION WEDGENUTWASHERTYPE 304 STAINLESSAISI 1018 - 12L14 orequivalent free-machiningcarbon steelANCHOR BODYAISI C1008 - 1010 orequivalent carbon steelEXPANSION WEDGEASTM A-563 Grade ACarbon SteelCarbon SteelType 304Cu (1/4" thru 3/4"diameters); Type 3-4 (7/8" thru1-1/4" diameters & all lengthsover 7")Type 304 stainlessNUT18-8 stainlessWASHER18-8 stainlessSee average test values as listed in the tables on pages 8-9.IMPORTANT: The maximum working loads should not exceed 1/4 of the average ultimate values for a specific size.Ultimate Shear StrengthSteel wedge anchors are typically zinc or mechanically galvanized plated.PlatingLENGTH IDENTIFICATION CODELength identification indicates overall length of anchor. Stamp is visible before and after installation.ABCDEFGHIJKLMMarkFromUp -1/2"8"NOPQRSTUVWXYZMarkFromUp 2"9"9-1/2"10"11"12"13"14"15"16"17"18"19"* Up to but not includingwww.allfasteners.com Customer Service 800 577 3171Doc: WedgeAnchorTDS Version Date: 04/22/19 Page 2 of 10

TECHNICAL DATA SHEET:WEDGE ANCHORZINC, GALVANIZED & STAINLESS STEELINSTALLATION GUIDE11. Using the proper drill bit size, drill a hole into the base material to the required depth. The tolerances of the drill bit used shouldmeet the requirements of ANSI Standard B212.15.22. Remove dust and debris from hole using a hand pump, compressed air or a vacuum to remove loose particles left from drilling33. Remove dust and debris from hole using a hand pump, compressed air or a vacuum to remove loose particles left from drilling.44. Tighten the anchor with a torque wrench by applying the required installation torque, TinstNote: the threaded stud will draw up during tightening of the nut; the expansion wedge (clip) remains in original position.www.allfasteners.com Customer Service 800 577 3171Doc: WedgeAnchorTDS Version Date: 04/22/19 Page 3 of 10

TECHNICAL DATA SHEET:WEDGE ANCHORZINC, GALVANIZED & STAINLESS STEELINSTALLATION SPECIFICATIONSlldhd, dbit overall anchor lengthd anchor diameterdbit drill diameter clearance hole diameter in fixturedhhnom minimum embedment depthhef effective embedment depthhot minimum hole depth fixture thicknessThe minimum base material thickness shouldbe 1.5 hnom or 3”, whichever is greater.hnomFor SI: 1 inch 25.4 mm, 1 ft-lbf 1.356 Nm.thoINSTALLATION SPECIFICATIONS - ZINC PLATED & HOT DIPPED GALVANIZEDCARBON STEEL - NOMINAL ANCHOR DIAMETER, dSetting Information1/43/81/25/83/47/811-1/4Nominal drill diameter, dbit1/43/81/25/83/47/811-1/4Fixture clearance holediameter, dh5/167/169/1611/1613/1611-1/81-3/8Nominal embedment depth, hnom1-3/42-3/85-5/85-1/85-1/47-1/4Effective embedment depth, hef1-1/22Minimum anchor length, lanch1-3/42-1/42-3/43-1/24-1/4669Torque wrench 0175225375Minimum hole depth, hoInstallation Torque /84-7/87-1/4INSTALLATION SPECIFICATIONS - STAINLESS STEEL TYPE 304 & 316STAINLESS STEEL - NOMINAL ANCHOR DIAMETER, dSetting Information1/43/81/25/83/47/811-1/4Nominal drill diameter, dbit1/43/81/25/83/47/811-1/4Fixture clearance holediameter, dh5/167/169/1611/1613/1611-1/81-3/8Nominal embedment depth, -1/47-1/4Effective embedment depth, 3/44-3/44-1/25-3/4Minimum hole depth, ho22-1/24-7/84-7/87-1/4Minimum anchor length, lanch1-3/42-1/42 3/43-1/24-1/4669Torque wrench 0175225375Installation Torque (ft-lb)www.allfasteners.com Customer Service 800 577 3171Doc: WedgeAnchorTDS Version Date: 04/22/19 Page 4 of 10

TECHNICAL DATA SHEET:WEDGE ANCHORZINC, GALVANIZED & STAINLESS STEELTECHNICAL DATABelow data applies to all anchor codes 1WAZ (Zinc Plated), 1WAG (Galvanized), 1WAS2 (304 Stainless Steel, and 1WAS4 (316Stainless Steel).ULTIMATE LOAD CAPACITIES FOR CARBON STEEL WEDGEANCHOR IN NORMAL WEIGHT Depth(in)ALLOWABLE LOAD CAPACITIES FOR CARBON STEELWEDGE ANCHOR IN NORMAL WEIGHT CONCRETEMINIMUM CONCRETECOMPRESSIVE STRENGTH(f'c)3500 352-3/8AnchorDiameter(in)EmbedmentDepth(in)MINIMUM CONCRETECOMPRESSIVE STRENGTH(f'c)3500 eners.com Customer Service 800 577 3171Doc: WedgeAnchorTDS Version Date: 04/22/19 Page 5 of 101/43/81/25/83/4

TECHNICAL DATA SHEET:WEDGE ANCHORZINC, GALVANIZED & STAINLESS STEELTECHNICAL DATA (CONT'D)Below data applies to all anchor codes 1WAZ (Zinc Plated), 1WAG (Galvanized), 1WAS2 (304 Stainless Steel, and1WAS4 (316 Stainless Steel).ULTIMATE LOAD CAPACITIES FOR CARBON STEEL WEDGEANCHOR IN NORMAL WEIGHT in)ALLOWABLE LOAD CAPACITIES FOR CARBON STEELWEDGE ANCHOR IN NORMAL WEIGHT CONCRETEMINIMUM CONCRETECOMPRESSIVE STRENGTH(f'c)4000 n)MINIMUM CONCRETECOMPRESSIVE STRENGTH(f'c)4000 108697106737/811-1/4SETTING - BASE MATERIAL THICKNESS (BMT)There is a recommended minimum thickness of the solid base material that the anchor can be set in.The minimum is based on 1.5 times of the calculated embedment to be used. Eg. an anchor to beinstalled to a depth of 4”, the base material should be 6” deep.Embedment - a pre-determined depth to obtain the required load capacity. Equal to or greater than theminimum embedment allowance.Drill Depth - is the required embedment depth into the substrate plus a cavity allowance approximately 1.5 times the anchor diameter.www.allfasteners.com Customer Service 800 577 3171Doc: WedgeAnchorTDS Version Date: 04/22/19 Page 6 of 10

TECHNICAL DATA SHEET:WEDGE ANCHORZINC, GALVANIZED & STAINLESS STEELSETTING - SPACINGThe anchor diameter is equal to the drill diameter which eliminates the need for hole plotting or layout. As the anchor can be spaced usingthe fixture the maximum load in tension or shear can be achieved by spacing anchors 10 times the selected diameter.This spacing can be reduced but the load value should also be reduced, see table below.Anchor SPACINGLOAD CAPACITY10 x D9xD8xD7xD6xD5xDReduce by100%10%20%30%40%50%Reduction Factor1.000.900.800.700.600.50SETTING - EDGE DISTANCE FOR TENSIONShould be determined by 12 times the selected anchor diameter to obtain the maximum load in tension. The recommended minimumspacing is 5 times the selected anchor diameter.In tension – reducing the edge distance to the minimum, the load value will reduce by 20%.Edge Distance in TENSION onlyLOAD CAPACITY12 x D11 x DReduce by100%3%Reduction Factor1.000.9710 x 830.80SETTING - EDGE DISTANCE FOR SHEARShould be determined by 12 times the selected anchor diameter to obtain the maximum load in shear. The recommended minimum spacingis 5 times the selected anchor diameter.In shear – reducing the edge distance to the minimum, the load value will reduce by 50%.Edge Distance in SHEAR onlyLOAD CAPACITY12 x D11 x D10 x D9xD8xD7xD6xD5xDReduce byReduction 0.840.570.50www.allfasteners.com Customer Service 800 577 3171Doc: WedgeAnchorTDS Version Date: 04/22/19 Page 7 of 10

TECHNICAL DATA SHEET:WEDGE ANCHORZINC, GALVANIZED & STAINLESS STEELORDERING INFORMATION - ZINC PLATED & HOT DIPPED GALVANIZEDLENGTH SELECTIONThe published length is the overall length of the anchor. Allow for fixture thickness plus one anchor diameter for the nut and washerthickness when selecting a length.Minimum Length Requirement must be the minimum Embedment Depth Fixture thickness (incl. shims & spacers) Anchor diameterCARBON STEEL AF WEDGE ANCHORSZINC ClearHD GALV.Anchor* xO.A.L 1WAG346141WAG347001WAG348121/4 x 1-3/41/4 x 2-1/41/4 x 3-1/43/8 x 2-1/43/8 x 2-3/43/8 x 33/8 x 3-1/23/8 x 3-3/43/8 x 51/2 x 2-3/41/2 x 3-3/41/2 x 4-1/41/2 x 4-1/21/2 x 5-1/21/2 x 71/2 x 8-1/25/8 x 3-1/25/8 x 4-1/25/8 x 55/8 x 65/8 x 75/8 x 8-1/25/8 x 103/4 x 4-1/43/4 x 4-3/43/4 x 5-1/23/4 x 6-1/43/4 x 73/4 x 8-1/2MIN.Embedment (in.)1-1/81-1/21-7/82-1/22-7/8ThreadLength 1-3/42-1/433-3/44-1/26*Drill diameterO.A.L is Overall Lengthwww.allfasteners.com Customer Service 800 577 3171Doc: WedgeAnchorTDS Version Date: 04/22/19 Page 8 of 10Washer O.Dø (in.)Hex NutA/F 20015010010010010010075754040606060604040

TECHNICAL DATA SHEET:WEDGE ANCHORZINC, GALVANIZED & STAINLESS STEELORDERING INFORMATION (CONT'D) - ZINC & HOT DIPPED GALVANIZEDCARBON STEEL AF WEDGE ANCHORSZINC ClearHD GALV.Anchor* xO.A.L WAG114901WAG114127/8 x 67/8 x 87/8 x 107/8 x 121x61x91 x 121-1/4 x 91-1/4 x 12MIN.Embedment (in.)3-7/84-1/25-1/2ThreadLength Washer O.Dø (in.)Hex NutA/F 5*Drill diameterO.A.L is Overall LengthORDERING INFORMATION - STAINLESS STEEL TYPE 304 & 316LENGTH SELECTIONThe published length is the overall length of the anchor. Allow for fixture thickness plus one anchor diameter for the nut and washerthickness when selecting a length.Minimum Length Requirement must be the minimum Embedment Depth Fixture thickness (incl. shims & spacers) Anchor diameterSTAINLESS STEEL AF WEDGE ANCHORSTYPE 304TYPE 316Anchor* xO.A.L 383001WAS

22.04.2019 · Hex Nut ASTM A563 Grade A Carbon Steel ASTM A563 Grade A Carbon Steel Flat Washer Carbon Steel Carbon Steel Plating/Finish Electroplated zinc plating (clear) Hot Dipped Galvanized. TECHNICAL DATA SHEET: WEDGE ANCHOR ZINC, GALVANIZED STAINLESS STEEL Doc: WedgeAnchorTDS Version Date: 04/22/19 Page 2 of 10 www.allfasteners.com Customer