Hard Disk Drive Specifications Models: 2R015H1 & 2R010H1

Transcription

Hard Disk Drive SpecificationsModels: 2R015H1 & 2R010H1P/N:1525/rev. AThis publication could include technical inaccuracies or typographicalerrors. Changes are periodically made to the information herein – whichwill be incorporated in revised editions of the publication. Maxtor maymake changes or improvements in the product(s) described in thispublication at any time and without notice.Copyright 2001 Maxtor Corporation. All rights reserved. Maxtor ,MaxFax and No Quibble Service are registered trademarks of MaxtorCorporation. Other brands or products are trademarks or registeredtrademarks of their respective holders.Corporate Headquarters510 Cottonwood DriveMilpitas, California 95035Tel: 408-432-1700Fax: 408-432-4510Research and Development Center2190 Miller DriveLongmont, Colorado 80501Tel: 303-651-6000Fax: 303-678-2165

Before You BeginYouThank you for your interest in Maxtor hard drives. This manual provides technical information for OEM engineersand systems integrators regarding the installation and use of Maxtor hard drives. Drive repair should be performedonly at an authorized repair center. For repair information, contact the Maxtor Customer Service Center at 8002MAXTOR or 408-922-2085.Before unpacking the hard drive, please review Sections 1 through 4.CAUTIONMaxtor hard drives are precision products. Failure to follow these precautions and guidelinesoutlined here may lead to product failure, damage and invalidation of all warranties.123456BEFORE unpacking or handling a drive, take all proper electro-static discharge (ESD)precautions, including personnel and equipment grounding. Stand-alone drives aresensitive to ESD damage.BEFORE removing drives from their packing material, allow them to reach roomtemperature.During handling, NEVER drop, jar, or bump a drive.Once a drive is removed from the Maxtor shipping container, IMMEDIATELY securethe drive through its mounting holes within a chassis. Otherwise, store the drive on apadded, grounded, antistatic surface.NEVER switch DC power onto the drive by plugging an electrically live DC source cableinto the drive's connector. NEVER connect a live bus to the drive's interface connector.ELECTRICAL GROUNDING - For proper operation, the drive must be securely fastenedto a device bay that provides a suitable electrical ground to the drive baseplate.Please do not remove or cover up Maxtor factory-installed drive labels.They contain information required should the drive ever need repair.

ContentsSection 1 — IntroductionMaxtor CorporationProductsSupportManual OrganizationAbbreviationsConventionsKey WordsNumberingSignal Conventions1-11-11-11-11-11-21-21-21-2Section 2 — Product DescriptionProduct FeaturesFunctional/InterfaceZone Density RecordingRead/Write Multiple ModeUltra ATA - Mode 5Multi-word DMA (EISA Type B) - Mode 2Sector Address TranslationLogical Block AddressingDefect Management ZoneOn-the-Fly Hardware Error Correction Code (ECC)Software ECC CorrectionAutomatic Head Park and Lock OperationCache ManagementBuffer SegmentationRead-Ahead ModeAutomatic Write Reallocation (AWR)Write Cache StackingMajor HDA ComponentsDrive MechanismRotary ActuatorRead/Write ElectronicsRead/Write Heads and MediaAir Filtration SystemMicroprocessorSubsystem ConfigurationDual Drive SupportCable Select OptionJumper Location/ConfigurationCylinder -42-42-42-42-52-52-52-52-52-52-52-62-62-62-62-6i

Section 3 — Product SpecificationsModels and CapacitiesDrive ConfigurationPerformance SpecificationsPhysical DimensionsPower RequirementsPower Mode A Energy Star ComplianceEnvironmental LimitsShock and VibrationReliability SpecificationsAnnual Return RateQuality Acceptance RateStart/Stop CyclesData ReliabilityComponent Design LifeEMC/EMIEMC ComplianceCanadian Emissions StatementSafety Regulatory -33-43-43-43-43-43-43-43-53-53-53-5Section 4 — Handling and InstallationHard Drive Handling PrecautionsElectro-Static Discharge (ESD)Unpacking and InspectionRepackingPhysical InstallationBefore You BeginPlease ReadBack up. Protect Your Existing DataTools for InstallationSystem RequirementsOperating System RequirementsHook upBoot the System with MaxBlast Plus DisketteConfigure the Drive JumpersInstallaing 5.25-inch Mounting BracketsInstall Hard Drive in Device BayAttach Interface and Power CablesStart upSet -54-54-54-5

Section 5 — AT Interface DescriptionInterface ConnectorPin Description SummaryPin Description TablePIO TimingDMA TimingUltra DMA Timing Parameters5-15-15-25-35-45-5Section 6 — Host Software InterfaceTask File RegistersData RegisterError RegisterFeatures RegisterSector Count RegisterSector Number RegisterCylinder Number RegistersDevice/Head RegisterStatus RegisterCommand RegisterRead CommandsWrite CommandsMode Set/Check CommandsPower Mode CommandsInitialization CommandsSeek, Format, and Diagnostic CommandsS.M.A.R.T. CommandsSummaryControl Diagnostic RegistersAlternate Status RegisterDevice Control RegisterDigital Input RegisterReset and Interrupt 6-36-36-36-46-56-56-56-56-6Section 7 — Interface CommandsCommand SummaryRead CommandsRead Sector(s)Read Verify Sector(s)Read Sector BufferRead DMARead MultipleSet MultipleWrite CommandsWrite Sector(s)7-17-27-27-27-27-37-37-37-47-4iii

Write Verify Sector(s)Write Sector BufferWrite DMAWrite MultipleMode Set/Check CommandsSet Features ModeRead Native Max AddressSet MaxSet Max PasswordSet Max LockSet Max UnlockSet Max Freeze LockPower Mode CommandsStandby ImmediateIdle ImmediateStandbyIdleCheck Power ModeSet Sleep ModeDefault Power-on ConditionInitialization CommandsIdentify DriveInitialize Drive ParametersSeek, Format, and Diagnostic CommandsS.M.A.R.T. Command 87-87-87-87-97 - 107 - 107 - 137 - 147 - 15Section 8 — Service and SupportService PolicyNo Quibble ServiceSupportGlossaryiv8-18-18-1

-45-55-65-75-85-95 - 105 - 115 - 125 - 13PCBA Jumper Location and ConfigurationOutline and Mounting DimensionsMulti-pack Shipping ContainerSingle-pack Shipping Container (Option A)Single-pack Shipping Container (Option B)IDE Interface and Power Cabling DetailData ConnectorPIO Data Transfer to/from DeviceMulti-word DMA Data TransferInitiating an Ultra DMA Data In BurstSustained Ultra DMA Data In BurstHost Pausing an Ultra DMA Data In BurstDevice Terminating an Ultra DMA Data In BurstHost Terminating an Ultra DMA Data In BurstInitiating an Ultra DMA Data Out BurstSustained Ultra DMA Data Out BurstDevice Pausing an Ultra DMA Data Out BurstHost Terminating an Ultra DMA Data Out BurstDevice Terminating an Ultra DMA Data Out 5-85-95-95 - 10v

INTRODUCTIONSECTION 1IntroductionMaxtor CorporationMaxtor Corporation has been providing high-quality computer storage products since 1982. Along the way,we’ve seen many changes in data storage needs. Not long ago, only a handful of specific users needed more thana couple hundred megabytes of storage. Today, downloading from the Internet and CD-ROMs, multimedia,networking and advanced office applications are driving storage needs even higher. Even home PC applicationsneed capacities measured in gigabytes, not megabytes.ProductsMaxtor’s products meet the demanding data storage capacity requirements of today and tomorrow. They areavailable in 5400- and 7200- RPM configurations with capacity offerings from 10 to 80 GB and beyond.SupportNo matter which capacity, all Maxtor hard drives are supported by our commitment to total customersatisfaction and our No Quibble Service guarantee. One call – or a visit to our home page on the Internet(www.maxtor.com) – puts you in touch with either technical support or customer service. We’ll provideyou the information you need quickly, accurately and in the form you prefer – a fax, a downloaded file ora conversation with a representative.Manual OrganizationThis hard disk drive reference manual is organized in the following method:Section 1Section 2Section 3Section 4Section 5Section 6Section 7Section oduct DescriptionProduct SpecificationsHandling and InstallationAT Interface DescriptionHost Software InterfaceInterface CommandsService and SupportGlossaryAbbreviationsABB RV DESC RIPTIONATA AT attachmentbpi bits per i nchCHS cyli nder - head - sectordb decibelsdBA dec ibels, A wei ghtedDMA di rect memory accessEC C error correction codefci fl ux changes per i nchG ac cel erationGB gi gabyteHz hertzKB kilobyteLBA logical bl ock address (ing)LSB l east significant bi tmA milliamperesABB RV DESC RIPTIONMB megabyteMbits/sec megabits per s econdMB/sec megabytes per s econdM Hz megahertzms millis econdMSB most significant bi tmV m illivoltsns nanosecondsPIO programmed i nput/outputRPM revoluti ons per mi nutetpi tracks per i nchUDMA ultra di rect memory accessµsec micros econdV voltsW watts1–1

INTRODUCTIONConventionsIf there is a conflict between text and tables, the table shall be accepted as being correct.Key WordsThe names of abbreviations, commands, fields and acronyms used as signal names are in all uppercase type(e.g., IDENTIFY DRIVE). Fields containing only one bit are usually referred to as the “name” bit instead ofthe “name” field.Names of drive registers begin with a capital letter (e.g., Cylinder High register).NumberingNumbers that are not followed by a lowercase “b” or “h” are decimal values. Numbers that are followed bya lowercase “b” (e.g., 01b) are binary values. Numbers that are followed by a lowercase “h” (e.g., 3Ah) arehexadecimal values.Signal ConventionsSignal names are shown in all uppercase type.All signals are either high active or low active signals. A dash character (-) at the end of a signal nameindicates that the signal is low active. A low active signal is true when it is below ViL and is false when it isabove ViH. A signal without a dash at the end indicates that the signal is high active. A high active signal istrue when it is above ViH and is false when it is below ViL.When a signal is asserted, it means the signal is driven by an active circuit to its true state.When a signal is negated, it means the signal is driven by an active circuit to its false state.When a signal is released, it means the signal is not actively driven to any state. Some signals have biascircuitry that pull the signal to either a true or false state when no signal driver is actively asserting or negatingthe signal. These instances are noted under the description of the signal.1–2

PRODUCT DESCRIPTIONSECTION 2Product DescriptionMaxtor hard disk drives are 3.5-inch diameter random access storage devices which incorporate an on-board UltraATA/100 controller. High capacity is achieved by a balanced combination of high areal recording density and thelatest data encoding and servo techniques.Maxtor's latest advancements in electronic packaging and integration methods have lowered the drive's powerconsumption and increased its reliability. Advanced giant magneto-resistive read/write heads and a state-of-the-arthead/disk assembly - using an integrated motor/spindle design - allow up to four disks in a 3.5-inch package.Key FeaturesANSI ATA-5 compliant PIO Mode 5 interface (Enhanced IDE)Supports Ultra DMA Mode 5 for up to 100 MBytes/sec data transfers2 MB buffer with multi-adaptive cache manager5400 RPM spin speed15 ms average seek timeZone density and I.D.-less recordingOutstanding shock resistance at 300 GsHigh durability with 50K contact start/stop cyclesAdvanced multi-burst on-the-fly Error Correction Code (ECC)Extended data integrity with ECC protected data and fault tolerant servo synchronization fieldsSupports EPA Energy Star Standards (Green PC Friendly) with ATA powering savings commandsAuto park and lock actuator mechanismLow power consumptionS.M.A.R.T. CapabilityNote: Maxtor defines one megabyte as 10E6 or one million bytes and one gigabyte as 10E9 or one billion bytes.2–1

PRODUCT DESCRIPTIONProduct FeaturesFunctional / InterfaceMaxtor hard drives contain all necessary mechanical and electronic parts to interpret control signals andcommands from an AT-compatible host computer. See Section 3 Product Specifications, for complete drivespecifications.Zone Density RecordingThe disk capacity is increased with bit density management – common with Zone Density Recording. Eachdisk surface is divided into 16 circumferential zones. All tracks within a given zone contain a constantnumber of data sectors. The number of data sectors per track varies in different zones; the outermost zonecontains the largest number of data sectors and the innermost contains the fewest.Read / Write Multiple ModeThis mode is implemented per ANSI ATA/ATAPI-5 specification. Read/Write Multiple allows the host totransfer a set number of sectors without an interrupt request between them, reducing transfer processoverhead and improving host performance.Ultra ATA/100 - Mode 5Maxtor hard drives fully comply with the new ANSI Ultra DMA protocol, which greatly improves overallAT interface performance by significantly improving burst and sustained data throughput.Multi-word DMA (EISA Type B) - Mode 2Supports multi-word Direct Memory Access (DMA) EISA Type B mode transfers.Sector Address TranslationAll Maxtor hard drives feature a universal translate mode. In an AT/EISA-class system, the drive may beconfigured to any specified combination of cylinders, heads and sectors (within the range of the drive'sformatted capacity). Maxtor hard drives power-up in a translate mode:MODEL SC YLHDSP TMAX LB AC APAC IT Y2R015H129 065166329 297 52015.0 GB2R010H119 853166320 011 82410.2 GBLogical Block AddressingThe Logical Block Address (LBA) mode can only be utilized in systems that support this form of translati

Before Y ou Begin Thank you for your interest in Maxtor hard drives. This manual provides technical information for OEM engineers and systems integrators regarding the installation and use of