Prüfbericht / Test Report Nr. / No. 06528-08998-01 (Edition 4)

Transcription

July 3, 2017Page 1 of 50Nr. / No. 06528-08998-01 (Edition 4)Prüfbericht / Test ReportApplicant:IQ Air AGType of equipment:Air Purifier with RFID reader modulType designation:ATEM Air Purifier (Type 03)Order No.:--Test standards:FCC Code of Federal Regulations,CFR 47, Part 15,Sections 15.205, 15.207, 15.215 and 15.225Industry Canada Radio Standards SpecificationsRSS-GEN Issue 4, Sections 8.8, 8.9 and 8.10 andRSS-210 Issue 9, Section B.6 (Category I Equipment)Note:The test data of this report is related only to the individual item which has beentested. This report shall not be reproduced except in full extent without the writtenapproval of the testing laboratory.Trade Register MunichHRB 85742VAT ID No. DE129484267Information pursuant to Section 2(1)DL-InfoV (Germany) atwww.tuev-sued.com/imprintManagement:Robert KeesDr. Jens ButenandtHolger LindnerPhone: 49 9421 55 22-0Fax: 49 9421 55 22-99www.tuev-sued.deTÜV SÜD Product Service GmbHÄußere Frühlingstraße 4594315 StraubingGermany

TÜV SÜD Product Service GmbHÄußere Frühlingstraße 4594315 StraubingGermanyPhone:Fax:Web: 49 9421 5522-0 49 9421 5522-99www.tuev-sued.deTable of Contents123456Description of the Equipment Under Test (EUT) . 3Administrative Data . 4Identification of the Test Laboratory . 5Summary . 6Operation Mode and Configuration of EUT . 7Measurement Procedures . 86.1Bandwidth Measurements. 86.2Conducted AC Powerline Emission . 106.3Radiated Emission Measurement 9 kHz to 30 MHz . 126.4Radiated Emission in Fully or Semi Anechoic Room . 146.5Radiated Emission at Alternative Test Site . 176.6Carrier Frequency Stability. 197Test Results . 217.1Occupied Bandwidth . 237.2Bandwidth of the Emission . 277.3Designation of Emissions . 297.4Conducted Powerline Emission Measurement 150 kHz to 30 MHz . 307.5Spectrum Mask . 337.6Radiated Emission Measurement 9 kHz to 30 MHz . 357.7Radiated Emission Measurement 30 MHz to 1 GHz . 387.8Carrier Frequency Stability. 407.9Exposure of Humans to RF Fields . 438Referenced Regulations . 479Test Equipment List with Calibration Data . 4910 Revision History . 50Test Report No. 06528-08998-01 (Edition 4)Page 2 of 50 Pages

TÜV SÜD Product Service GmbHÄußere Frühlingstraße 4594315 StraubingGermany1Phone:Fax:Web: 49 9421 5522-0 49 9421 5522-99www.tuev-sued.deDescription of the Equipment Under Test (EUT)General data of EUTType of equipment:Air Purifier with RFID reader modulParts1:--Serial number(s):000105Manufacturer:IQ Air AGType designation2:ATEM Air Purifier (Type 03)Version:V1FCC ID:2AMBQ-ATEM03Industry Canada ID:22813-ATEM03Additional parts/accessories:--Technical data of EUTApplication frequency range:13.110 - 14.010 MHzFrequency range:13.553 – 13-567 MHzOperating frequency:13.56 MHzType of modulation:ASKPulse train:--Pulse width:--Number of RF-channels:1Channel spacing:--Designation ofemissions3:40k2A1DType of antenna:OnboardSize/length of antenna:--Connection of antenna:detachablenot detachableType of power supply:DC supplySpecifications for power supply:nominal voltage:minimum voltage:maximum voltage:5.0 V4.5 V5.5 Vnominal frequency:DC Hz1Type designations of the parts of the system, if applicable.Type designation of the system if EUT consists of more than one part.3 Also known as "Class of Emission".2Test Report No. 06528-08998-01 (Edition 4)Page 3 of 50 Pages

TÜV SÜD Product Service GmbHÄußere Frühlingstraße 4594315 StraubingGermany2Phone:Fax:Web: 49 9421 5522-0 49 9421 5522-99www.tuev-sued.deAdministrative DataApplication detailsApplicant (full address):IQ Air AGBlumenfeldstrasse 10CH-9403 GoldachContact person:Mr. VorburgerOrder number:--Receipt of EUT:2017-05-16Date(s) of test:2017-05-22 & 2017-05-23Note(s):--Report detailsReport number:06528-08998-01Edition:4Issue date:July 3, 2017Test Report No. 06528-08998-01 (Edition 4)Page 4 of 50 Pages

TÜV SÜD Product Service GmbHÄußere Frühlingstraße 4594315 StraubingGermany3Phone:Fax:Web: 49 9421 5522-0 49 9421 5522-99www.tuev-sued.deIdentification of the Test LaboratoryDetails of the Test LaboratoryCompany name:TÜV SÜD Product Service GmbHAddress:Aeussere Fruehlingstrasse 45D-94315 StraubingGermanyLaboratory accreditation:DAkkS Registration No. D-PL-11321-11-01Laboratory recognition:Registration No. BNetzA-CAB-16/21-15Industry Canada test site registration:3050A-2Contact person:Mr. Markus BibergerPhone: 49 9421 5522-0Fax: 49 9421 5522-99Test Report No. 06528-08998-01 (Edition 4)Page 5 of 50 Pages

TÜV SÜD Product Service GmbHÄußere Frühlingstraße 4594315 StraubingGermany4Phone:Fax:Web: 49 9421 5522-0 49 9421 5522-99www.tuev-sued.deSummarySummary of test resultsThe tested sample complies with the requirements set forth in theCode of Federal Regulations CFR 47, Part 15, Sections 15.205, 15.207, 15.215 and 15.225of the Federal Communication Commission (FCC) and theRadio Standards SpecificationsRSS-GEN Issue 4, Sections 8.8, 8.9 and 8.10 andRSS-210 Issue 9, Section , B.6 (Category I Equipment)of Industry Canada (IC).Die Prüfergebnisse beziehen sich ausschließlich auf das zur Prüfung vorgestellte Prüfmuster. Ohne schriftliche Genehmigung des Prüflabors darf der Prüfbericht auszugsweise nicht vervielfältigt werden. The test results relate only to the individual item which has been tested.Without the written approval of the test laboratory this report may not be reproduced in extracts.Datum / DateGeprüft von / Tested byFreigabe durch / Checked byPrüfergebnis / Test ResultErfüllt / PassedJuly 3, 2017Markus BibergerResponsible for testingTest Report No. 06528-08998-01 (Edition 4)Martin SteindlReviewerNicht erfüllt / Not passedPage 6 of 50 Pages

TÜV SÜD Product Service GmbHÄußere Frühlingstraße 4594315 StraubingGermany5Phone:Fax:Web: 49 9421 5522-0 49 9421 5522-99www.tuev-sued.deOperation Mode and Configuration of EUTOperation Mode(s)The EUT is transmitting continuously at 13,56MHz withwith the RFID tag in the HEPA-FilterSoftware: IQAir Product Interface V 000.62Configuration(s) of EUTThe EUT is configured via IQAir product interface to continuously transmit with the RFID tag ("rfidEmcTestEnable")List of ports and cablesPortDescriptionClassification4Cable typeCable length1Power supplydc powerUnshielded1.8mItem DescriptionType DesignationSerial no. or IDManufacturer1Test notebookE460TPS-STR-NB04Lenovo2USB BLE module------Type DesignationSerial no. or IDManufacturerList of devices connected to EUTList of support devicesItem Description--4Ports shall be classified as ac power, dc power or signal/control portTest Report No. 06528-08998-01 (Edition 4)Page 7 of 50 Pages

TÜV SÜD Product Service GmbHÄußere Frühlingstraße 4594315 StraubingGermanyPhone:Fax:Web:6Measurement Procedures6.1Bandwidth Measurements 49 9421 5522-0 49 9421 5522-99www.tuev-sued.deMeasurement Procedure:Rules and specifications:CFR 47 Part 2, section 2.202(a)CFR 47 Part 15, section 15.215(c)IC RSS-Gen Issue 4, section 6.6IC RSS-210 Issue 9, section A.1.3ANSI C63.10, section 6.9.1Guide:ANSI C63.10 / IC RSS-Gen Issue 4, section 6.6Measurement setup:Conducted: See belowRadiated:Radiated Emission Measurement 9 kHz to 30 MHz (6.3)EUTEUTPowersupplyLISNDC blockand/orattenuatorIf antenna is detachable bandwidth measurements shall be performed at the antenna connector (conductedmeasurement) when the transmitter is adjusted in accordance with the tune-up procedure, if applicable. TheRF output terminals are connected to a spectrum analyzer. If required, a resistive matching network equal tothe impedance specified or employed for the antenna is used as well as dc block and appropriate attenuators(50 Ohms). The electrical characteristics of the radio frequency load attached to the output terminals shall bestated, if applicable.If radiated measurements are performed the same test setups and instruments are used as with radiatedemission measurements for the appropriate frequency range.The analyzer settings are specified by the test description of the appropriate test record(s).Spectrum analyzerWoodentableTest Report No. 06528-08998-01 (Edition 4)Page 8 of 50 Pages

TÜV SÜD Product Service GmbHÄußere Frühlingstraße 4594315 StraubingGermanyPhone:Fax:Web: 49 9421 5522-0 49 9421 5522-99www.tuev-sued.deTest instruments used for conducted measurements:TypeDesignationInv.-no.Serial No. or IDManufacturerSpectrum analyzerEMI test receiverEMI test receiverFSV40ESPI7ESMI236417111569Rohde & SchwarzRohde & SchwarzRohde & SchwarzPower meterPeak power sensorPower sensorPower sensorDC-blockMicrowave 4776-104776-20EMC32 rdaNardaRohde & SchwarzAttenuatorAttenuatorMeasurement SoftwareTest Report No. 06528-08998-01 (Edition 4)Rohde & SchwarzRohde & SchwarzRohde & SchwarzRohde & SchwarzWeinschelHuber SuhnerPage 9 of 50 Pages

TÜV SÜD Product Service GmbHÄußere Frühlingstraße 4594315 StraubingGermany6.2Phone:Fax:Web: 49 9421 5522-0 49 9421 5522-99www.tuev-sued.deConducted AC Powerline EmissionMeasurement Procedure:Rules and specifications:CFR 47 Part 15, section 15.207IC RSS-Gen Issue 4, section 8.8Guide:ANSI C63.10 / CISPR 22Conducted emission tests in the frequency range 150 kHz to 30 MHz are performed using Line ImpedanceStabilization Networks (LISNs). To simplify testing with quasi-peak and average detector the following procedure is used:First the whole spectrum of emission caused by the equipment under test (EUT) is recorded with detector setto peak using CISPR bandwidth of 10 kHz. After that all emission levels having less margin than 10 dB to orexceeding the average limit are retested with detector set to quasi-peak.If average limit is kept with quasi-peak levels no additional scan with average detector is necessary. In casesof emission levels between quasi-peak and average limit an additional scan with detector set to average isperformed.According to ANSI C63.10, section 6.2.5, testing of intentional radiators with detachable antenna shall beperformed using a suitable dummy load connected to the antenna output terminals. Otherwise, the tests shallbe made with the antenna connected and, if adjustable, fully extended.Testing with dummy load may be necessary to distinguish (unintentional) conducted emissions on the supplylines from (intentional) emissions radiated by the antenna and coupling directly to supply lines and/or LISN.Usage of dummy load has to be stated in the appropriate test record(s) and notes should be added to clarifythe test setup.Shielded roomEMI receiverEUTEUTLISNWoodentableTest Report No. 06528-08998-01 (Edition 4)Page 10 of 50 Pages

TÜV SÜD Product Service GmbHÄußere Frühlingstraße 4594315 StraubingGermanyPhone:Fax:Web: 49 9421 5522-0 49 9421 5522-99www.tuev-sued.deTest instruments used:TypeDesignationInv.-no.Serial No. or IDManufacturerTest receiverESCI31000008Rohde & SchwarzV-networkV-networkArtificial mains networkMicrowave cableESH 3-Z5ESH 3-Z5ESH /005830952/025842966/00472110-02Coax cableShielded roomShielded roomMeasurement SoftwareRG214 N/N 5mNo. 1No. 4EMC32 K1 V9.26.011188145114542230----3FD 100 544100281Rohde & SchwarzRohde & SchwarzRohde & eldRohde & SchwarzTest Report No. 06528-08998-01 (Edition 4)Page 11 of 50 Pages

TÜV SÜD Product Service GmbHÄußere Frühlingstraße 4594315 StraubingGermany6.3Phone:Fax:Web: 49 9421 5522-0 49 9421 5522-99www.tuev-sued.deRadiated Emission Measurement 9 kHz to 30 MHzMeasurement Procedure:Rules and specifications:CFR 47 Part 15, sections 15.205, 15.215(b) and 15.225(a)-(d)IC RSS-GEN Issue 4, sections 8.9 and 8.10 andIC RSS-210 Issue 9, section B.6Guide:ANSI C63.10Radiated emission in the frequency range 9 kHz to 30 MHz is measured using an active loop antenna. Firstthe whole spectrum of emission caused by the equipment is recorded at a distance of 3 meters in a fully orsemi anechoic room with the detector of the spectrum analyzer or EMI receiver set to peak. This configurationis also used

Applicant: IQ Air AG Type of equipment: Air Purifier with RFID reader modul Type designation: ATEM Air Purifier (Type 03) Order No.: -- Test standards: FCC Code of Federal Regulations, CFR 47, Part 15, Sections 15.205, 15.207, 15.215 and 15.225 Industry Canada Radio Standards Specifications RSS-GEN Issue 4, Sections 8.8, 8.9 and 8.10 and