Transcription
EZ-SCREEN (TYPE 2)EZ-SCREEN (TYPE 4)GRIDS & POINTSEZ-SCREEN Type 2 Point-of-OperationMACHINE SAFETY A low-cost solution is suited to lower-risk applications where the result of anaccident is only a slight injury such as a bump, bruise, knockdown or trapping(but not crushing), minor cuts and abrasions Simple two-piece system requires no control box 30 mm resolution detects narrow objects, such as a hand or ankle across longspans up to 15 m System meets all requirements for Type 2 devices per IEC 61496 and Cat 2 PL dper EN ISO 13849-1 (CE certified) and cULus NIPF System performs continual internal self-tests and provides Test function forexternal safety checks Dedicated models eliminate selectable functions, DIP switches and programming Trip output model automatically resets when the beam is cleared; Latch outputmodel requires a manual reset Fast response times of 11 to 29 milliseconds shutdown machinery quicklyACCESSORIESpage53831.8 mmFull ViewonlineLAUTOCAD, STEP,IGES & PDFEZ-SCREENType 2 Systems534Yellow Painted Aluminum25.2 mmMore information online at bannerengineering.com
EZ-SCREEN Type 2 Systems, 30 mm Resolution Model Key, 24V dcPhotoelectricsSensorsModel Style ConnectionResolutionDefined AreaEmitter/ReceiverPair †LS2TE30T TripL LatchE EmitterR ReceiverP Pair †30 30 mm150Q8orFiber OpticSensorsMeasurement &Inspection SensorsSpecial PurposeSensorsVisionQ8 8-pin QDLighting &IndicatorsWireless150300450600750900Housing Response # ofLengthTimeBeams 215 mm 11 ms8 365 mm13 ms16 515 mm14 ms24 665 mm16 ms32 815 mm17 ms40 964 mm19 ms48105012001350150016501800Housing Response # ofLengthTimeBeams 1114 mm 21 ms56 1264 mm22 ms64 1414 mm24 ms72 1563 mm25 ms80 1713 mm27 ms88 1863 mm29 ms86Q88 Receiver with 8-pin QDEmitter with 8-pin QDSafetyLight ScreensSafetyLaser ScannersSafety Controllers &ModulesSafety Two-HandControl ModulesSafety InterlockSwitchesEmergency Stop &Stop ControlACCESSORIESpage538†A pair includes an emitter and receiver (example, LS2TP30-150Q88)Contact Banner Engineering Corp. for additional information and/or verification of valid kit model numbers.EZ-SCREENTYPE 414 or 30 mmTYPE 4LOW PROFILE14 or 25 mmTYPE 230 mmGRIDS & POINTSCall for more information 1.888.373.6767535
EZ-SCREEN (TYPE 2)EZ-SCREEN (TYPE 4)GRIDS & POINTSEZ-SCREEN Type 2 KitsMACHINE SAFETYYou can purchase a kit that contains an emitter and receiver of equal length; brackets; and optional interfacingsolution and quick-disconnect cordsets. Detailed information about individual kit components is as follows. Emitter and ReceiversACCESSORIESPage 535 Interfacing Options545 Cordsets538 Brackets538To Order:1. Choose model, output and defined area.2. Choose an optional interfacing solution, such as an IM-T-9A or -11interfacing model.3. Choose one cordset for each sensor or two cordsets for a pair.All models require mating 8-pin M12/Euro QD cordsets, such as:- QDE cordset with flying leads- DEE2R double-ended cordset- CSB series splitter cordsetSee www.bannerengineering.com for complete information and a current listingof accessories and options for kitting components. Call factory with questionsregarding accessories.page538EZ-SCREEN Type 2 Systems Kits Model KeyModel StyleKitResolutionLS2TLS2T Type 2 Light Screen (trip)LS2L Type 2 Light Screen (latch)DefinedAreaConnectionK30150K Kit30 30 mm150 900300 1050450 1200600 1350750Q88Q88 E mitter with 8-pin QDReceiver with 8-pin QDInterfacingOptionsQD CordsetLength Options1RE25RE15 4.5 m, 2 eachRE25 7.6 m, 2 eachR15E25 7.6 m (Emitter) & 4.5 m (Receiver)R25E15 5 m (Emitter) & 8 m (Receiver)RE50 15.2 m, 2 eachR15E50 15.2 m (Emitter) & 4.6 m (Receiver)R50E15 4.6 m (Emitter) & 15.2 m (Receiver)R25E50 15.2 m (Emitter) & 7.6 m (Receiver)R50E25 7.6 m (Emitter) & 15.2 m (Receiver)RE75 22.8 m, 2 eachRE100 30.4 m, 2 each1 IM-T-9A Interface Module, 1 each (3 NO)2 IM-T-11A Interface Module, 1 each (2 NO/ 1 NC)3 11-BG00-31-D-024 Contactors (10A), 2 each4 BF1801L-024 Contactors (18A), 2 each10 UM-FA-9A, 1 each11 UM-FA-11A, 1 eachContact Banner Engineering Corp. for additional information and/or verification of valid kit model numbers.536More information online at bannerengineering.com
EZ-SCREEN Type 2 SpecificationsPhotoelectricsSensorsSupply Voltage at the Device24V dc 20% (PELV) (The external voltage supply must be capable of buffering brief mains interruptions of20 milliseconds as specified in EN/IEC 60204-1.)Fiber OpticSensorsSupply CurrentEmitter: 50 mA max.Receiver: 90 mA max., exclusive of OSSD1 and OSSD2 loads (up to an additional 0.5A each)Wavelength of Emitter ElementsInfrared LEDs, 950 nm at peak emissionVisionShort Circuit ProtectionAll inputs and outputs are protected from short circuits to 24V dc or dc commonLighting &IndicatorsElectrical Safety Class(IEC 61140)IIIOperating Range0 .2 m to 15 mRange decreases with use of mirrors and/or lens shields:Lens shields – approximately 10% less range per shieldGlass-surface mirrors – approximately 8% less range per mirrorSee Accessory section for more information on a specific mirror, page 655Measurement &Inspection SensorsSpecial PurposeSensorsWirelessSafetyLight ScreensSafetyLaser ScannersSafety Controllers &ModulesSafety Two-HandControl ModulesEffective Aperture Angle (EAA)Meets Type 2 requirements per IEC 61496-2; 5 @ 3 mAmbient Light Immunity 10,000 lux at 5 angle of incidenceSafety InterlockSwitchesStrobe Light ImmunityImmune as per IEC 61496-2Emergency Stop &Stop ControlResponse TimeDependent on number of beams; see Models table on page 535EDM Input“Power Monitoring” accomplished via Reset/Remote Test inputReset Input / Remote Test InputConnect to 24V dc via a normally closed (NC) reset switchAuto Rest (Trip Output) Models: Test/ResetManual Rest (Latch Output) Models: Test/Restart/ResetSafety OutputsTwo redundant solid-state 24V dc, 0.5 A max. sourcing OSSD (Output Signal Switching Device) safety outputs. (Use optionalinterface modules for ac or larger dc loads.)Not compatible with the Banner “Safety Handshake”ON-State voltage: Vin-1.5V dcOFF-State voltage: 0.2V dc max.Max. load capacitance: 0.1 µFMin. load resistance: 48 ΩOpen ground leakage current: 0.65 mA max.OSSD test pulse width: 0.2 - 0.25 millisecondsOSSD test pulse period: 260 milliseconds typicalEnclosureMaterials: Extruded aluminum housing with yellow polyester powder finish and well-sealed, rugged die-cast zinc end caps,acrylic lens coverRating: IP65Operating ConditionsTemperature: 0 to 55 CShock and VibrationEZ-SCREEN Type 2 components have passed vibration and shock tests according to IEC 61496-1. This includes vibration(10 cycles) of 10-55 Hz at 0.35 mm single amplitude (0.70 mm peak-to-peak) and shock of 10 g for 16 milliseconds (6,000 cycles).Design StandardsDesigned to comply with Type 2 per IEC 61496-1/-2; Category 2 Pl d per EN ISO 13849-1; SIL 2 per IEC 61 508;Type 2 per UL 61496-1/-2EZ-SCREENTYPE 414 or 30 mmTYPE 4LOW PROFILE14 or 25 mmTYPE 230 mmGRIDS & POINTSRelative humidity: 95% maximum (non-condensing)CertificationsWiring DiagramsEmitter: WD008 (p. 823)Receiver with 2 Solid-State OSSDs, 2 FSDs and Power Monitoring: WD009 (p. 824)Power Monitoring of IM-T-9A Interface Module: WD010 (p. 824)Call for more information 1.888.373.6767537
EZ-SCREEN (TYPE 2)EZ-SCREEN (TYPE 4)GRIDS & POINTSMACHINE SAFETYCordsetsEuro QDEuro QD–Double-EndedSee page 732See page 733Length8-PinLengthQDE-815D4.57 mSee page 735Length8-Pin0.31 mDEE2R-81DEuro QD Splitter8-Pin0mCSB-M1280M1280CSB-M1281M12817.62 mQDE-825D0.91 mDEE2R-83D0.3 m15.3 mQDE-850D2.44 mDEE2R-88D2.50 mCSB-M1288M128122.9 mQDE-875D4.57 mDEE2R-815D4.60 mCSB-M12815M128130.5 mQDE-8100D7.62 mDEE2R-825D7.60 mCSB-M12825M128115.2 mDEE2R-850D7.60 mCSB-UNT825M128122.9 mDEE2R-875D30.5 mDEE2R-8100DAdditional cordset information available.See page 721.Brackets30 mm–Type 2pg. 719pg. 720USCMB-.pg. 720USMB-1pg. 720USMB-6USMB-8Additional bracket information available.See page 656.NOTE: See page 545 for interfacing solutions.Replacement PartsModelDescriptionMGA-K-1Replacement key for switch MGA-KS0-1MGA-KS0-1Panel-mount keyed normally open reset switchSTP-1430 mm test pieceUSMB-1Standard end brackets with hardware to mount to MSA series standsUSCMB-1Center bracket kit and standard end brackets with hardware to mount to MSA series stands (1 bracket, for 600 to 900 mm long sensors)USCMB-2Center bracket kit and standard end brackets with hardware to mount to MSA series stands (2 brackets, for 1050 to 1500 mm long sensors)Note: See installation manual p/n 112852 for complete list of replacement parts and accessories.538STANDSMIRRORSPAGE 766PAGE 770More information online at bannerengineering.comLENS SHIELDSPAGE 776INTERFACEPAGE 545
EZ-SCREEN TYPE 4 14 or 30 mm TYPE 4 LOW PROFILE 14 or 25 mm TYPE 2 30 mm GRIDS & POINTS †airncludes A p i an emitter and receiver (example, LS2TP30-150Q88) Contact Banner Engineering Corp. for additional information and/or verification of valid kit model numbers. EZ-SCREEN Type 2 Sys
